The brake pedal load sensing switch turns on when the brake pedal is depressed with a force exceeding a predetermined level. The skid control ECU (brake actuator assembly) uses this circuit to detect if the brake pedal is depressed or not.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1430 | Brake Pedal Load Sensing Switch OFF Stuck Malfunction | Either of the following is detected:
1.
With the stop light switch assembly on, the brake pedal load sensing switch off, and the master cylinder pressure more than 6 MPa (61.2 kgf/cm2, 870 psi), the vehicle acceleration rate is less than -4 m/s2 for 1 second or more. 2.
With the stop light switch assembly on, the brake pedal load sensing switch off, and the master cylinder pressure more than 6 MPa (61.2 kgf/cm2, 870 psi), the vehicle speed is 0 km/h (0 mph) for 5 seconds or more. |
·
Brake pedal load sensing switch (brake pedal support assembly) ·
Brake pedal load sensing switch circuit |
| C1431 | Brake Pedal Load Sensing Switch ON Stuck Malfunction | Either of the following is detected:
1.
With the stop light switch assembly off, the brake pedal load sensing switch on, and the master cylinder pressure less than 0.7 MPa (7.13 kgf/cm2, 101 psi), the vehicle acceleration rate is more than -0.8 m/s2 for 10 seconds or more. (Only when the engine is running and brake booster malfunctions are not detected.) 2.
Condition which the brake pedal load sensing switch remains on while the vehicle speed increases from 0 km/h (0 mph) to 30 km/h (19 mph) occurs 5 times in succession. |
·
Brake pedal load sensing switch (brake pedal support assembly) ·
Brake pedal load sensing switch circuit |
Refer to DTC C1429 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1429).
When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
When C1249, C1425 and/or C1426 is output together with C1430 and/or C1431, inspect and repair the trouble areas indicated by C1249, C1425 and/or C1426 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1249 for C1249, Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425 for C1425 and/or Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1426 for C1426).
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stop Light SW | Stop light switch assembly / ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Brake Pedal Load Sensing SW | Brake pedal load sensing switch / ON or OFF | ON: Brake pedal depressed beyond a specified point
OFF: Brake pedal not depressed beyond a specified point |
- |
Check that the stop light switch assembly display and brake pedal load sensing switch display observed on the GTS change according to brake pedal operation.
The GTS displays ON or OFF according to brake pedal operation.
Slowly depress the brake pedal, and check when the stop light switch assembly and brake pedal load sensing switch turn on.
First the stop light switch assembly turns on, and then the brake pedal load sensing switch turns on.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Turning on of the brake pedal load sensing switch is not confirmed.) | B |
| NG (The brake pedal load sensing switch turns on first.) | C |
A
B
C
Turn the engine switch off.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Start the engine.
Perform a road test.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1430 and C1431 are not output. | A |
| DTCs C1430 and/or C1431 are output. | B |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
Turn the engine switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A38 or A40 brake pedal load sensing switch (brake pedal support assembly) connector.
Do not remove the brake pedal load sensing switch from the brake pedal support assembly.
When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal support assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (FSW+) - 1 (FSW-) | Switch OFF (Brake pedal depressed) | 950 to 1050 Ω |
| 2 (FSW+) - 1 (FSW-) | Switch ON (Brake pedal released) | 203 to 223 Ω |
| *a | Component without harness connected
(Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly)) |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A35 skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
for LHD
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-34 (FSW+) - A40-2 (FSW+) | Always | Below 1 Ω |
| A35-34 (FSW+) or A40-2 (FSW+) - Body ground | Always | 10 kΩ or higher |
| A40-1 (FSW-) - Body ground | Always | Below 1 Ω |
for RHD
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-34 (FSW+) - A38-2 (FSW+) | Always | Below 1 Ω |
| A35-34 (FSW+) or A38-2 (FSW+) - Body ground | Always | 10 kΩ or higher |
| A38-1 (FSW-) - Body ground | Always | Below 1 Ω |
OK
NG
Turn the engine switch off.
Check the brake pedal height (See page Brake>BRAKE>BRAKE PEDAL>ADJUSTMENT).
Check the stop light switch assembly installation (See page Brake>BRAKE>BRAKE PEDAL>INSTALLATION).
The brake pedal height and stop light switch assembly installation are normal.
OK
NG