Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1271  Low Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1272  Low Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1330  Open in Front Speed Sensor RH  C1331  Open in Front Speed Sensor LH  C1464  Front Speed Sensor RH  C1465  Front Speed Sensor LH  


DESCRIPTION

Each speed sensor detects wheel speed and sends signals to the skid control ECU (brake actuator assembly). These signals are used by the ABS.

The speed sensor rotors have rows of alternating N and S magnetic poles. The speed sensors use the frequency of output pulses to detect the vehicle speed. Because the sensor outputs digital pulses, it can detect the vehicle speed even when the vehicle is nearly stationary.

DTCs C1271 and C1272 are cleared when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs C1271 and C1272 are output only in Test Mode.

C223506E17
1.281,1.063 1.281,0.708 1.281,0.708 1.073,0.708 false 0.177,0.615 1.365,0.927 1.188,0.313 10 false Speed Sensor 4.958,1.948 5.802,2.135 0.844,0.188 10 false High speed 4.021,1.958 4.802,2.146 0.781,0.188 10 false Low speed 6.031,1.135 6.49,1.406 0.458,0.271 10 false 0.3 V 6.021,1.479 6.583,1.698 0.563,0.219 10 false 0.15 V 0.906,2.177 2.365,2.385 1.458,0.208 10 false Speed Sensor Rotor

DTC No. Detection Item DTC Detection Condition Trouble Area
C1271 Low Output Signal of Front Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Front speed sensor RH

·

Sensor installation

·

Front speed sensor rotor RH (front axle hub sub-assembly RH)


C1272 Low Output Signal of Front Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Front speed sensor LH

·

Sensor installation

·

Front speed sensor rotor LH (front axle hub sub-assembly LH


C1330 Open in Front Speed Sensor RH An open or short in the speed sensor signal circuit.
·

Front speed sensor RH

·

Speed sensor circuit

·

Sensor installation


C1331 Open in Front Speed Sensor LH An open or short in the speed sensor signal circuit.
·

Front speed sensor LH

·

Speed sensor circuit

·

Sensor installation


C1464 Front Speed Sensor RH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), a wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a front wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

-

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

-

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

-

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Front speed sensor RH

·

Speed sensor circuit

·

Front speed sensor rotor RH (front axle hub sub-assembly RH)

·

Sensor installation

·

Skid control ECU (brake actuator assembly)


C1465 Front Speed Sensor LH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), a wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a front wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

-

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

-

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

-

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Front speed sensor LH

·

Speed sensor circuit

·

Front speed sensor rotor LH (front axle hub sub-assembly LH)

·

Sensor installation

·

Skid control ECU (brake actuator assembly)



HINT:
·

DTCs C1271, C1330 and C1464 are for the front speed sensor RH.

·

DTCs C1272, C1331 and C1465 are for the front speed sensor LH.



WIRING DIAGRAM

C243493E88
1.167,1.125 1.292,1.281 0.125,0.156 10 false 2 2.344,1.125 2.469,1.281 0.125,0.156 10 false 1 1.042,1.563 1.375,1.823 0.333,0.26 10 false A20 1.063,3.75 2.635,4 1.573,0.25 10 false Front Speed Sensor LH 5.51,4.073 7.073,4.438 1.563,0.365 10 false Skid Control ECU (Brake Actuator Assembly) 5.688,0.563 5.885,0.729 0.198,0.167 10 false 16 5.76,1.125 5.938,1.292 0.177,0.167 10 false 4 5.688,2.594 5.885,2.76 0.198,0.167 10 false 19 5.76,3.167 5.958,3.333 0.198,0.167 10 false 8 5.51,3.885 5.885,4.083 0.375,0.198 10 false A35 5.99,0.667 6.313,0.823 0.323,0.156 10 false FR+ 5.979,1.25 6.302,1.406 0.323,0.156 10 false FR- 5.979,2.708 6.302,2.865 0.323,0.156 10 false FL+ 5.979,3.281 6.302,3.438 0.323,0.156 10 false FL- 1.042,1.719 2.615,1.969 1.573,0.25 10 false Front Speed Sensor RH 1.063,3.583 1.417,3.844 0.354,0.26 10 false A5 1.167,3.167 1.292,3.323 0.125,0.156 10 false 2 2.323,3.177 2.448,3.333 0.125,0.156 10 false 1 1.354,3.24 1.677,3.396 0.323,0.156 10 false FL+ 2,3.24 2.323,3.396 0.323,0.156 10 false FL- 1.354,1.198 1.677,1.354 0.323,0.156 10 false FR+ 2,1.198 2.323,1.354 0.323,0.156 10 false FR-

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations


d.

Check the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.




OK

2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

4.CHECK FRONT SPEED SENSOR INSTALLATION
2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the engine switch off.


b.

Perform the sensor check using the Test Mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).

OK:

No Test Mode DTCs are output.




OK

3.RECONFIRM DTC

NG

4.CHECK FRONT SPEED SENSOR INSTALLATION
3.RECONFIRM DTC
a.

Turn the engine switch off.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.



Result:
Result Proceed to
DTCs C1330, C1331, C1464 and C1465 are not output. A
DTCs C1330, C1331, C1464 and/or C1465 are output. B



A

B

8.REPLACE FRONT SPEED SENSOR
4.CHECK FRONT SPEED SENSOR INSTALLATION
a.
C168336E23
1.042,0.865 1.219,0.5 false 0.906,1.49 1.167,1.729 false 0.125,0.083 0.552,0.281 0.427,0.198 10 false *1 0.729,1.823 1.198,2.031 0.469,0.208 10 false *a 2.438,1.865 2.75,2.063 0.313,0.198 10 false *b 1.188,0.333 1.5,0.531 0.313,0.198 10 false *c 1.208,1.708 1.521,1.906 0.313,0.198 10 false *d

Turn the engine switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.

Torque

8.5 N*m (87 kgf*cm, 75 in.*lbf)


Text in Illustration
*1 Front Speed Sensor
*a Correct
*b Incorrect
*c 8.5 N*m
*d No clearance



OK

5.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR

NG

5.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR
a.

Remove the front speed sensor and the component with the sensor rotor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL for speed sensor, Drivetrain>AXLE>FRONT AXLE HUB>REMOVAL for sensor rotor).


b.

Check the speed sensor tip and speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the sensor tip and rotor.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.

·

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).





OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR OR COMPONENT WITH SENSOR ROTOR

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
a.

Install the front speed sensor and the component with the sensor rotor.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A35 skid control ECU (brake actuator assembly) connector and A5 or A20 front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A35-16 (FR+) - A20-2 (FR+) Always Below 1 Ω
A35-16 (FR+) or A20-2 (FR+) - Body ground Always 10 kΩ or higher
A35-4 (FR-) - A20-1 (FR-) Always Below 1 Ω
A35-4 (FR-) or A20-1 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A35-19 (FL+) - A5-2 (FL+) Always Below 1 Ω
A35-19 (FL+) or A5-2 (FL+) - Body ground Always 10 kΩ or higher
A35-8 (FL-) - A5-1 (FL-) Always Below 1 Ω
A35-8 (FL-) or A5-1 (FL-) - Body ground Always 10 kΩ or higher




OK

7.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.RECONFIRM DTC
a.

Reconnect the A35 skid control ECU (brake actuator assembly) connector and A5 or A20 front speed sensor connector.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.



Result:
Result Proceed to
DTCs C1330, C1331, C1464 and/or C1465 are output. A
DTCs C1330, C1331, C1464 and C1465 are not output. B



A

8.REPLACE FRONT SPEED SENSOR

B

8.REPLACE FRONT SPEED SENSOR
a.

Turn the engine switch off.


b.

Replace the front speed sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL).

NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




NEXT

9.RECONFIRM DTC
9.RECONFIRM DTC

b.

Turn the engine switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.



Result:
Result Proceed to
DTCs C1330, C1331, C1464 and/or C1465 are output. A
DTCs C1330, C1331, C1464 and C1465 are not output. B



A

10.REPLACE FRONT AXLE HUB SUB-ASSEMBLY

B

END

10.REPLACE FRONT AXLE HUB SUB-ASSEMBLY
a.

Turn the engine switch off.


b.

Replace the front speed sensor rotor (front axle hub sub-assembly) (See page Drivetrain>AXLE>FRONT AXLE HUB>REMOVAL).

HINT:

The front speed sensor rotor is incorporated into the front axle hub sub-assembly.

If the front speed sensor rotor needs to be replaced, replace the front axle hub sub-assembly.


NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




NEXT

11.RECONFIRM DTC
11.RECONFIRM DTC

b.

Turn the engine switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1330, C1331, C1464 and C1465 are not output. A
DTCs C1330, C1331, C1464 and/or C1465 are output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

END

B