Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.04–2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1426/49  Stop Switch OFF Stuck  


DESCRIPTION

The skid control ECU receives stop light switch signals and uses them to determine whether or not the brakes are applied.

The skid control ECU has a detection circuit that it uses to detect a short in the stop light input line, or the ground line of the stop light circuit with the stop light switch on (brake pedal depressed).

If the skid control ECU detects a short in this circuit, it will store this DTC.

DTC No. DTC Detection Condition Trouble Area
C1426/49 Either of the following is detected:
1.

With the stop light switch off, the stop light switch is judged to be on based on the master cylinder pressure value for 3 seconds or more.

2.

With the stop light switch off, the master cylinder pressure is more than 8 MPa (81.6 kgf/cm2, 1160 psi) for 3 seconds or more.


·

STOP fuse

·

Stop light switch

·

Stop light switch circuit

·

Stop light control (BRK-LP) relay

·

Stop light control (BRK-LP) relay circuit

·

Skid control ECU (ABS and TRACTION actuator)



PROCEDURE

1.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
a.

Check the brake pedal height and stop light switch installation (See page Brake>BRAKE>BRAKE PEDAL>ADJUSTMENT).

OK:

The brake pedal height and stop light switch installation are normal.


HINT:

If the on/off status of the stop light switch and the pressure increase information from the master cylinder pressure sensor do not match due to an improperly installed brake pedal or stop light switch, this DTC may be stored. Therefore, be sure to check the installation condition of the pedal and switch before inspecting the input signals and other related parts.




OK

2.CHECK STOP LIGHT OPERATION

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH

2.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. ON
Brake pedal released. OFF




OK

3.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)

NG

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
3.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Select the Data List using the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


d.

Check that the stop light switch display observed on the intelligent tester changes according to brake pedal operation.

OK:

The intelligent tester displays on or off according to brake pedal operation.




OK

4.RECONFIRM DTC

NG

13.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
4.RECONFIRM DTC
a.

Turn the engine switch off.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC is not output A
DTC is output (for 2AZ-FE) B
DTC is output (for 2GR-FE) C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

C

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
U189483E02
0.188,0.146 2.573,0.49 2.385,0.344 10 false Front view of wire harness connector: (to Stop Light Switch) 0.542,1.917 0.865,2.167 0.323,0.25 10 false A33

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the stop light switch connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A33-2 - Body ground Always 11 to 14 V




OK

6.INSPECT STOP LIGHT SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

6.INSPECT STOP LIGHT SWITCH
a.
C156543E07
0.12,0.177 2.702,0.533 2.582,0.356 10 Component without harness connected: (Stop Light Switch) 0.337,2.584 0.663,2.744 0.326,0.160 10 Free 1.256,2.584 1.913,2.744 0.657,0.160 10 Pushed in 3.162,1.387 3.303,1.557 0.141,0.170 10 2 3.162,2.372 3.280,2.543 0.117,0.170 10 1 2.846,1.926 3.142,1.495 false 2.846,2.027 3.142,2.459 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Switch pin free Below 1 Ω
1 - 2 Switch pin pushed in 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
U189329E02
1.74,1.792 1.865,2.313 false 0.135,0.25 2.75,0.396 2.615,0.146 10 false Front view of wire harness connector: 0.469,0.865 0.667,1.01 0.198,0.146 10 false A9 1.708,2.313 2.135,2.479 0.427,0.167 10 false STP 0.135,0.438 1.521,0.583 1.385,0.146 10 false (to Skid Control ECU)

Reconnect the stop light switch connector.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A9-30 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 8 to 14 V
A9-30 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V




OK

8.INSPECT STOP LIGHT CONTROL RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

8.INSPECT STOP LIGHT CONTROL RELAY
a.

Check the stop light control relay (See page Vehicle Interior>LIGHTING>STOP LIGHT CONTROL RELAY>INSPECTION).


OK:

The stop light control relay is normal.



OK

9.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - ENGINE ROOM NO. 1 RELAY BLOCK)

NG

REPAIR OR REPLACE WIRE HARNESS OR STOP LIGHT CONTROL RELAY

9.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - ENGINE ROOM NO. 1 RELAY BLOCK)
a.
C205479E01
0.132,0.01 2.233,0.187 2.100,0.177 10 Engine Room No. 1 Relay Block: 1.965,2.198 3.137,2.534 1.172,0.336 10 Stop Light Control (BRK-LP) Relay

Remove the stop light control (BRK-LP) relay.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Stop light control (BRK-LP) relay terminal 4 - Body ground Stop light switch ON (Brake pedal depressed) 8 to 14 V
Stop light control (BRK-LP) relay terminal 4 - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V




OK

10.INSPECT STOP LIGHT CONTROL (BRK-LP) RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT STOP LIGHT CONTROL (BRK-LP) RELAY
a.
C366275E01
2.5,1.563 2.24,1.104 false 2.74,1.938 3.073,1.094 false 2.083,2.938 2.24,2.469 false 2.604,2.99 2.604,2.469 false 3.115,2.969 2.948,2.448 false 0.125,0.094 2.583,0.49 2.458,0.396 10 false Stop Light Control (BRK-LP) Relay: 2.146,0.927 2.469,1.188 0.323,0.26 10 false 3 3.052,0.906 3.26,1.135 0.208,0.229 10 false 5 2.031,2.969 2.354,3.229 0.323,0.26 10 false 2 2.563,3 2.885,3.26 0.323,0.26 10 false 4 3.115,3.021 3.323,3.24 0.208,0.219 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Voltage is not applied between terminals 1 and 2 Below 1 Ω
3 - 5 Voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 4 Voltage is applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage is applied between terminals 1 and 2 Below 1 Ω




OK

11.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)

NG

REPLACE STOP LIGHT CONTROL (BRK-LP) RELAY

11.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)
a.
U189330E02
2.01,1.708 1.729,2.292 false 0.135,0.115 2.51,0.427 2.375,0.313 10 false Front view of wire harness connector: (to Skid Control ECU) 0.344,0.958 0.542,1.104 0.198,0.146 10 false A9 1.5,2.333 1.927,2.5 0.427,0.167 10 false STP2

Install the stop light control (BRK-LP) relay.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A9-13 (STP2) - Body ground Stop light switch ON (Brake pedal depressed) 8 to 14 V
A9-13 (STP2) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V




OK

12.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)

12.RECONFIRM DTC
a.

Reconnect the skid control ECU connector.



c.

Start the engine.


d.

Depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC is not output A
DTC is output (for 2AZ-FE) B
DTC is output (for 2GR-FE) C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

C

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
U189329E02
1.74,1.792 1.865,2.313 false 0.135,0.25 2.75,0.396 2.615,0.146 10 false Front view of wire harness connector: 0.469,0.865 0.667,1.01 0.198,0.146 10 false A9 1.708,2.313 2.135,2.479 0.427,0.167 10 false STP 0.135,0.438 1.521,0.583 1.385,0.146 10 false (to Skid Control ECU)

Turn the engine switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A9-30 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 8 to 14 V
A9-30 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V




OK

14.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

14.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
U189179E01
0.064,0.077 2.475,0.418 2.411,0.341 10 Front view of wire harness connector: (to Skid Control ECU) 0.196,1.315 0.462,1.452 0.266,0.137 10 A10 0.794,2.559 1.319,2.706 0.525,0.147 10 GND1 1.217,1.979 0.998,2.547 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A9-4 (GND1) - Body ground Always Below 1 Ω


Result:
Result Proceed to
OK (for 2AZ-FE) A
OK (for 2GR-FE) B
NG C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)