TRC OFF Indicator Light Remains ON
Circuit diagnosis · Vehicles built Aug 2012 – Oct 2012
Versions by build date: Aug 2008 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Oct 2012 Nov 2012 – Jul 2014 from Aug 2014
DESCRIPTION
The skid control ECU (master cylinder solenoid) is connected to the combination meter via the CAN communication system. Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction control and VSC. If TRC control turns off, the TRC OFF indicator light comes on.If there is a malfunction in the engine control system, the TRC and A-TRAC system will turn off and the TRC OFF indicator will turn on.
When the temperature inside the hydraulic brake booster becomes too high, the TRC OFF indicator light turns on and traction control is stopped until the temperature decreases.
for 4WD:
- When the transfer is in L4 (for Automatic Transmission) or LL (for Manual Transmission), VSC is prohibited and the VSC OFF indicator and TRC OFF indicator lights turn on.
- w/ Rear Differential Lock:
When the rear differential is locked, VSC is prohibited and the VSC OFF indicator and TRC OFF indicator lights turn on. At this time, ABS is also prohibited and the ABS warning light turns on.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the master cylinder solenoid, perform calibration (Click here).
- As there may be malfunctions in the transfer system related to when the transfer operates in L4 (for Automatic Transmission) or LL (for Manual Transmission), check the transfer system first (for automatic transmission: Click here, for manual transmission: Click here).
- When replacing the master cylinder solenoid, perform calibration (Click here).
| 1. CHECK DTC (ENGINE CONTROL SYSTEM) |
Check if any DTC is recorded for the engine control system (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | |
| 2. CHECK CAN COMMUNICATION LINE |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).
- OK:
- CAN Bus Check indicates no malfunctions in CAN communication.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (CSW CIRCUIT) |
Disconnect the A4 skid control ECU (master cylinder solenoid) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A4-9 (CSW) - Body ground
VSC OFF switch not pushed in
10 kΩ or higher
VSC OFF switch pushed in
Below 1 Ω
|
|
||||
| OK | |
| 4. INSPECT MASTER CYLINDER SOLENOID (EXI3 TERMINAL) |
w/ Rear Differential Lock
Disconnect the A4 skid control ECU (master cylinder solenoid) connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A4-40 (EXI3) - Body ground
Ignition switch ON
Rear differential free
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU (master cylinder solenoid))
w/o Rear Differential Lock
Disconnect the A4 skid control ECU (master cylinder solenoid) connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A4-40 (EXI3) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU (master cylinder solenoid))
Result Result
Proceed to
OK
A
NG (w/ Rear Differential Lock)
B
NG (w/o Rear Differential Lock)
C
|
|
||||
|
|
||||
| A | |
| 5. READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
| TRC/VSC Off Mode |
TRC/VSC off mode/ Normal, TRC OFF or VSC OFF |
Normal: Normal mode TRC OFF: TRC OFF mode VSC OFF: VSC OFF mode |
- |
Check that the mode display changes according to VSC OFF switch operation.
- OK:
- Display changes according to switch operation.
|
|
||||
| OK | ||
| ||
| 6. INSPECT VSC OFF SWITCH |
Remove the VSC OFF switch (Click here).
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
3 - 4
Switch is not pushed
10 kΩ or higher
Switch is pushed
Below 1 Ω
Text in Illustration *a
Component without harness connected
(VSC OFF Switch)
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - VSC OFF SWITCH) |
Disconnect the A4 skid control ECU (master cylinder solenoid) connector.
Disconnect the E77 VSC OFF switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A4-9 (CSW) - E77-3
Always
Below 1 Ω
A4-9 (CSW) - Body ground
Always
10 kΩ or higher
E77-4 - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 8. INSPECT MASTER CYLINDER SOLENOID (EXI3 CIRCUIT) |
Disconnect the A4 skid control ECU (master cylinder solenoid) connector.
Disconnect the L7 four wheel drive control ECU connector.
Disconnect the D2 rear differential lock detection switch (differential lock indicator switch) connector.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
A4-40 (EXI3) - Body ground
Always
10 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU (master cylinder solenoid))
|
|
||||
| OK | |
| 9. INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH) |
Remove the rear differential lock detection switch (differential lock indicator switch) (Click here).
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Pushed in
Below 1 Ω
Not pushed in
10 kΩ or higher
Text in Illustration *a
Component without harness connected
(Rear Differential Lock Detection Switch (Differential Lock Indicator Switch))
|
|
||||
| OK | |
| 10. INSPECT MASTER CYLINDER SOLENOID (EXI3 TERMINAL) |
Disconnect the A4 skid control ECU (master cylinder solenoid) connector.
Connect the L7 four wheel drive control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A4-40 (EXI3) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU (master cylinder solenoid))
|
|
||||
| OK | ||
| ||
