2011-2016 FJ Cruiser · Service Manual BRAKE

TRC OFF Indicator Light Remains ON

Circuit diagnosis · Vehicles built Nov 2012 – Jul 2014

Versions by build date: Aug 2008 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Oct 2012 Nov 2012 – Jul 2014 from Aug 2014

DESCRIPTION

The skid control ECU (master cylinder solenoid) is connected to the combination meter via the CAN communication system. Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction control and VSC. If TRC control turns off, the TRC OFF indicator light comes on.
If there is a malfunction in the engine control system, the TRC and A-TRAC system will turn off and the TRC OFF indicator will turn on.
When the temperature inside the hydraulic brake booster becomes too high, the TRC OFF indicator light turns on and traction control is stopped until the temperature decreases.
for 4WD:
  1. When the transfer is in L4 (for Automatic Transmission) or LL (for Manual Transmission), VSC is prohibited and the VSC OFF indicator and TRC OFF indicator lights turn on.
  2. w/ Rear Differential Lock:
    When the rear differential is locked, VSC is prohibited and the VSC OFF indicator and TRC OFF indicator lights turn on. At this time, ABS is also prohibited and the ABS warning light turns on.

WIRING DIAGRAM

C245122E01

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform calibration (Click here).
  2. As there may be malfunctions in the transfer system related to when the transfer operates in L4 (for Automatic Transmission) or LL (for Manual Transmission), check the transfer system first (for automatic transmission: Click here, for manual transmission: Click here).


1. CHECK DTC (ENGINE CONTROL SYSTEM)
  1. Check if any DTC is recorded for the engine control system (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO ENGINE CONTROL SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) (Click here)
A


2. CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (CSW CIRCUIT)
  1. Disconnect the A4 skid control ECU (master cylinder solenoid) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-9 (CSW) - Body ground
    VSC OFF switch not pushed in
    10 kΩ or higher
    VSC OFF switch pushed in
    Below 1 Ω



NG
Go to step 6
OK


4. INSPECT MASTER CYLINDER SOLENOID (EXI3 TERMINAL)

  1. w/ Rear Differential Lock

    1. Disconnect the A4 skid control ECU (master cylinder solenoid) connector.

    2. C214161E52
      Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A4-40 (EXI3) - Body ground
      Ignition switch ON
      Rear differential free
      11 to 14 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Skid Control ECU (master cylinder solenoid))

  1. w/o Rear Differential Lock

    1. Disconnect the A4 skid control ECU (master cylinder solenoid) connector.

    2. C214161E52
      Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A4-40 (EXI3) - Body ground
      Ignition switch ON
      11 to 14 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Skid Control ECU (master cylinder solenoid))
      Result 
      Result
      Proceed to
      OK
      A
      NG (w/ Rear Differential Lock)
      B
      NG (w/o Rear Differential Lock)
      C



B
Go to step 8

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
A


5. READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
TRC/VSC Off Mode
TRC/VSC off mode/ Normal, TRC OFF or VSC OFF
Normal: Normal mode
TRC OFF: TRC OFF mode
VSC OFF: VSC OFF mode
-
  1. Check that the mode display changes according to VSC OFF switch operation.

    OK:
    Display changes according to switch operation.



NG
REPLACE MASTER CYLINDER SOLENOID (Click here)
OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

6. INSPECT VSC OFF SWITCH
  1. Remove the VSC OFF switch (Click here).

  1. C234071E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 - 4
    Switch is not pushed
    10 kΩ or higher
    Switch is pushed
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (VSC OFF Switch)



NG
REPLACE VSC OFF SWITCH (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - VSC OFF SWITCH)
  1. Disconnect the A4 skid control ECU (master cylinder solenoid) connector.

  1. Disconnect the E77 VSC OFF switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-9 (CSW) - E77-3
    Always
    Below 1 Ω
    A4-9 (CSW) - Body ground
    Always
    10 kΩ or higher
    E77-4 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)

8. INSPECT MASTER CYLINDER SOLENOID (EXI3 CIRCUIT)
  1. Disconnect the A4 skid control ECU (master cylinder solenoid) connector.

  1. Disconnect the L7 four wheel drive control ECU connector.

  1. Disconnect the D2 rear differential lock detection switch (differential lock indicator switch) connector.

  1. C214161E53
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-40 (EXI3) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (master cylinder solenoid))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (EXI3 CIRCUIT)
OK


9. INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH)
  1. Remove the rear differential lock detection switch (differential lock indicator switch) (Click here).

  1. C214518E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pushed in
    Below 1 Ω
    Not pushed in
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Differential Lock Detection Switch (Differential Lock Indicator Switch))



NG
REPLACE REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH) (Click here)
OK


10. INSPECT MASTER CYLINDER SOLENOID (EXI3 TERMINAL)
  1. Disconnect the A4 skid control ECU (master cylinder solenoid) connector.

  1. Connect the L7 four wheel drive control ECU connector.

  1. C214161E53
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-40 (EXI3) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (master cylinder solenoid))



NG
REPLACE 4 WHEEL DRIVE CONTROL ECU NO. 2
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)


← TRC OFF Indicator Light Remains ON (Aug 2012 – Oct 2012)TRC OFF Indicator Light Remains ON (from Aug 2014) →