The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the turbocharger sub-assembly removal/installation are shown below.
| Replacement Part or Procedure | Necessary Procedures | Effects/Inoperative when not Performed | Link |
|---|---|---|---|
·
Replacement of turbocharger sub-assembly ·
Replacement of turbocharger nozzle vane control actuator |
Perform initialization | - |
|
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
12601B
1.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
25051
2.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/ EGR Cooler)
17167
3.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/o EGR Cooler)
17271
4.REMOVE NO. 1 TURBO INSULATOR (w/o EGR Cooler)
5.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY (w/o EGR Cooler)
6.REMOVE EXHAUST PIPE SUPPORT STAY (w/o EGR Cooler)
17291
7.REMOVE TURBINE OUTLET ELBOW (w/o EGR Cooler)
51406A
8.REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)
52618
9.REMOVE LOWER FRONT BUMPER ABSORBER
51405A
10.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
11.DRAIN ENGINE COOLANT
12.DRAIN ENGINE COOLANT (for Water Cooled Type Intercooler)
13.DRAIN ENGINE OIL
17940D
14.REMOVE INTERCOOLER ASSEMBLY (for Water Cooled Type Intercooler)
17030
15.REMOVE AIR HOSE ASSEMBLY (for Air Cooled Type Intercooler)
25761B
16.DISCONNECT NO. 1 VACUUM TRANSMITTING HOSE (for Air Cooled Type Intercooler)
17303T
17.REMOVE AIR PIPE SUB-ASSEMBLY (for Air Cooled Type Intercooler)
53106B
18.REMOVE RADIATOR COVER SUB-ASSEMBLY
17751
19.REMOVE NO. 1 AIR CLEANER INLET
44360
20.DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY
16640
21.REMOVE INTERCOOLER RESERVE TANK ASSEMBLY (for Water Cooled Type Intercooler)
16470
22.REMOVE RADIATOR RESERVE TANK ASSEMBLY
16571C
23.REMOVE NO. 1 RADIATOR HOSE
16552C
24.REMOVE NO. 2 INTERCOOLER COOLING WATER HOSE (for Water Cooled Type Intercooler)
165A0
25.REMOVE NO. 1 INTERCOOLER COOLING WATER HOSE ASSEMBLY (for Water Cooled Type Intercooler)
161B0
26.REMOVE ELECTRIC WATER PUMP ASSEMBLY (for Water Cooled Type Intercooler)
16515A
27.DISCONNECT INTERCOOLER COOLING WATER PIPE ASSEMBLY (for Water Cooled Type Intercooler)
16711
28.REMOVE FAN SHROUD
17705
29.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE
Disconnect the mass air flow meter sub-assembly connector and detach the harness clamp.
| *a | Air Cleaner Cap Clamp |
Detach the 2 air cleaner cap clamps.
Detach the 2 guides and disconnect the air cleaner cap sub-assembly from the air cleaner case sub-assembly.
Loosen the hose clamp and remove the air cleaner cap sub-assembly with air cleaner hose.
17801
30.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner filter element sub-assembly from the air cleaner case.
17701
31.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Remove the 3 bolts and air cleaner case sub-assembly.
32.REMOVE WATER HOSE SUB-ASSEMBLY (w/ Viscous Heater)
87120G
33.REMOVE VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (w/ Viscous Heater)
16279
34.REMOVE NO. 3 WATER BY-PASS PIPE
for Cold Area Specification Vehicles:
Slide the 2 hose clips and remove the water hose from the compressor inlet elbow and No. 3 water by-pass pipe.
| *A | for Cold Area Specification Vehicles |
| *B | except Cold Area Specification Vehicles |
Slide the 2 hose clips and disconnect the 2 water hoses from the oil cooler assembly and No. 2 water by-pass pipe sub-assembly.
Remove the bolt and No. 3 water by-pass pipe.
12229
35.REMOVE PCV PIPE (for Cold Area Specification Vehicles)
for Air Cooled Type Intercooler:
Slide the 2 hose clips and disconnect the No. 20 water by-pass hose from the PCV pipe and No. 1 water by-pass pipe.
Slide the hose clip and disconnect the No. 19 water by-pass hose from the compressor inlet elbow.
Remove the bolt and disconnect the PCV pipe from the compression outlet elbow.
Slide the 2 hose clips and remove the PCV pipe.
for Water Cooled Type Intercooler:
Slide the 2 hose clips and disconnect the No. 20 water by-pass hose from the PCV pipe and No. 1 water by-pass pipe.
Slide the hose clip and disconnect the No. 19 water by-pass hose from the compressor inlet elbow.
Remove the 2 bolts and disconnect the PCV pipe from the compression outlet elbow.
Slide the 2 hose clips and remove the PCV pipe.
12261
36.REMOVE PCV HOSE (except Cold Area Specification Vehicles)
Slide the 2 hose clips, detach the clamp and remove the PCV hose.
37.REMOVE WATER BY-PASS HOSE (for Water Cooled Compressor Housing Turbocharger)
Slide the 2 hose clips and disconnect the No. 21 water by-pass hose from the turbocharger sub-assembly and No. 1 water by-pass pipe.
Slide the 2 hose clips and disconnect the No. 4 turbo water hose from the turbocharger sub-assembly and No. 1 turbo water pipe sub-assembly.
16268
38.REMOVE NO. 1 WATER BY-PASS PIPE
16284
39.DISCONNECT TURBO WATER HOSE
| *A | w/ DPF |
| *B | w/o DPF |
Slide the 2 hose clips and disconnect the No. 1 turbo water hose and No. 2 turbo water hose from the water outlet sub-assembly and water pump assembly.
40.DISCONNECT BRACKET OIL COOLER TUBE BRACKET AND WIRE HARNESS CLAMP BRACKET (for Automatic Transmission)
Remove the bolt and disconnect the oil cooler tube bracket.
Remove the bolt and disconnect the wire harness.
41.DISCONNECT WIRE HARNESS CLAMP BRACKET (for Manual Transmission)
Remove the bolt and disconnect the wire harness.
87101
42.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (for Cold Area Specification Vehicles)
Remove the bolt, detach the clamp and disconnect the wire harness.
Remove the 4 bolts and No. 1 viscous heater bracket sub-assembly.
17293
43.REMOVE TURBOCHARGER STAY
Remove the 3 bolts, nut and turbocharger stay.
15474
44.REMOVE TURBO OIL OUTLET PIPE
Slide the 2 hose clips and disconnect the turbo oil outlet hose from the turbo oil outlet pipe.
Remove the 2 bolts, turbo oil outlet pipe and gasket.
15407
45.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY
Remove the union bolt and gasket.
Remove the 2 nuts and turbo oil inlet pipe sub-assembly.
Do not loosen the nut labeled A.
Remove the gasket.
17201
46.REMOVE TURBOCHARGER SUB-ASSEMBLY
| *A | w/ DPF |
| *B | w/o DPF |
Remove the 3 nuts and turbocharger sub-assembly.
Remove the gasket from the exhaust manifold.
25601
47.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/ EGR System)
25601
48.REMOVE EGR PIPE WITH COOLER SUB-ASSEMBLY (for Laminated EGR Pre-cooler)
25617
49.REMOVE EGR HOLE COVER PLATE (w/o EGR System)
Remove the 2 nuts, EGR hole cover plate and gasket.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts shown in the illustration.
17141
50.REMOVE EXHAUST MANIFOLD
| *A | w/ DPF |
| *B | w/o DPF |
Remove the 8 nuts, 8 plate washers, 8 collars and exhaust manifold.
Remove the gasket.
16027
51.REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY
| *A | w/ DPF |
| *B | w/o DPF |
except Water Cooled Compressor Housing Turbocharger:
Slide the 2 hose clips and disconnect the No. 1 turbo water hose and No. 2 turbo water hose from the No. 1 turbo water pipe sub-assembly.
| *A | w/ DPF |
| *B | w/o DPF |
for Water Cooled Compressor Housing Turbocharger:
Slide the 2 hose clips and disconnect the No. 1 turbo water hose and No. 2 turbo water hose from the No. 1 turbo water pipe sub-assembly.
Remove the bolt.
| *A | except Water Cooled Compressor Housing Turbocharger |
| *B | for Water Cooled Compressor Housing Turbocharger |
Remove the 2 nuts, No. 1 turbo water pipe sub-assembly and gasket.
17274
52.REMOVE COMPRESSOR INLET ELBOW
| *A | for Cold Area Specification Vehicles |
| *B | except Cold Area Specification Vehicles |
Remove the 2 bolts and compressor inlet elbow stay.
| *A | for Cold Area Specification Vehicles |
| *B | except Cold Area Specification Vehicles |
except Water Cooled Compressor Housing Turbocharger:
Remove the 2 nuts and compressor inlet elbow from the turbocharger sub-assembly.
| *A | for Cold Area Specification Vehicles |
| *B | except Cold Area Specification Vehicles |
for Water Cooled Compressor Housing Turbocharger:
Remove the 2 nuts and compressor inlet elbow from the turbocharger sub-assembly.
| *A | for Cold Area Specification Vehicles |
| *B | except Cold Area Specification Vehicles |
except Water Cooled Compressor Housing Turbocharger:
Using an E8 "TORX" socket wrench, remove the stud bolt shown in the illustration together with the compressor inlet elbow and gasket.
for Water Cooled Compressor Housing Turbocharger:
| *A | for Cold Area Specification Vehicles |
| *B | except Cold Area Specification Vehicles |
Using an E8 "TORX" socket wrench, remove the stud bolt shown in the illustration together with the compressor inlet elbow.
Remove the gasket from the compressor inlet elbow.
17275
53.REMOVE COMPRESSOR OUTLET ELBOW
| *A | for Cold Area Specification Vehicles |
| *B | except Cold Area Specification Vehicles |
for Air Cooled Type Intercooler:
Remove the 2 nuts and compressor outlet elbow.
Remove the gasket.
except Cold Area Specification Vehicles:
Remove the bolt and hose clamp.
for Water Cooled Type Intercooler:
Remove the 2 nuts and compressor outlet elbow.
Remove the gasket.
54.REMOVE STUD BOLT
If a stud bolt is deformed or its threads are damaged, replace it.
Using an E5 "TORX" socket wrench, remove the 4 stud bolts shown in the illustration.
Using an E8 "TORX" socket wrench, remove the 4 stud bolts shown in the illustration.
Using an E10 "TORX" socket wrench, remove the 3 stud bolts shown in the illustration.