When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
| Injector assembly (including shuffling the injector assemblies between the cylinders) | ·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly |
| Supply pump assembly | Fuel inlet pipe sub-assembly |
·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing chain case assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.
The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.
The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.
Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.
Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.
Make sure foreign matter does not enter the fuel path.
12632
1.REMOVE NO. 2 ENGINE COVER BRACKET (for Air Cooled Type Intercooler)
82121
2.REMOVE ENGINE WIRE
26100G
3.REMOVE DIESEL THROTTLE BODY ASSEMBLY
16278
4.REMOVE NO. 2 WATER BY-PASS PIPE
89481B
5.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ DPF)
89425
6.REMOVE EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)
25733A
7.REMOVE NO. 1 VACUUM PIPE (w/ DPF)
25734
8.REMOVE NO. 2 VACUUM PIPE (w/ DPF)
17578B
9.REMOVE PIPE CLAMP (w/ DPF)
12631A
10.REMOVE ENGINE COVER BRACKET (for Air Cooled Type Intercooler)
Remove the 2 bolts and engine cover bracket from the cylinder head sub-assembly.
17945
11.REMOVE INTERCOOLER SUPPORT BRACKET (for Water Cooled Type Intercooler)
Remove the 2 bolts and intercooler support bracket from the cylinder head sub-assembly.
89421C
12.REMOVE DIESEL TURBO PRESSURE SENSOR
23265C
13.REMOVE GAS FILTER
25625
14.REMOVE EGR VALVE BRACKET
25612
15.REMOVE NO. 2 EGR PIPE
16206B
16.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/ EGR Cooler)
16206B
17.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/o EGR Cooler)
Disconnect the No. 4 fuel hose from the No. 3 water by-pass pipe sub-assembly.
| *A | w/ EGR System |
| *B | w/o EGR System |
w/ EGR System:
Slide the clamp and disconnect the No. 8 water by-pass hose from the No. 3 water by-pass pipe sub-assembly.
Slide the clamp and disconnect the No. 9 water by-pass hose from the electric EGR control valve assembly.
Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly from the EGR valve adapter sub-assembly.
27148A
18.REMOVE CONNECTING WIRE
Disconnect the connector from the common rail assembly.
Detach the 2 clamps and remove the connecting wire from the hose bracket.
25601
19.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/ EGR System)
Remove the 4 nuts, bolt and No. 1 EGR pipe sub-assembly from the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.
Remove the 2 gaskets from the exhaust manifold and electric EGR control valve assembly.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.
25601
20.REMOVE EGR PIPE WITH COOLER SUB-ASSEMBLY (for Laminated EGR Pre-cooler)
Slide the 2 clamps and remove the water hose from the EGR pipe with cooler sub-assembly and No. 5 water by-pass pipe.
Remove the bolt and disconnect the No. 1 EGR pipe with cooler sub-assembly from the cylinder head sub-assembly.
Remove the 4 nuts and No. 1 EGR pipe with cooler sub-assembly from the exhaust manifold and EGR valve adapter.
Remove the 2 gaskets.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.
25804
21.REMOVE VACUUM CONTROL VALVE SET (w/ EGR Cooler)
16209
22.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY
| *A | for Cold Area Specification Vehicles |
| *B | except Cold Area Specification Vehicles |
| *1 | No. 6 Water By-pass Hose |
| *2 | No. 7 Water By-pass Hose |
| *3 | Water Hose |
| *4 | No. 11 Water By-pass Hose |
Slide the clamp and disconnect the No. 6 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.
Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.
Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.
for Cold Area Specification Vehicles:
Detach the clamp and disconnect the No. 11 water by-pass hose from the diesel throttle body assembly.
Remove the 2 bolts and No. 4 water by-pass pipe sub-assembly from the intake manifold.
25800
23.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System with EGR Cooler)
24.REMOVE EGR VALVE ADAPTER SUB-ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System without EGR Cooler)
Remove the 4 bolts and EGR valve adapter sub-assembly with electric EGR control valve assembly from the intake manifold.
25624
25.REMOVE EGR VALVE ADAPTER SUB-ASSEMBLY (w/o EGR System)
Remove the 4 bolts and EGR valve adapter sub-assembly from the intake manifold.
25617
26.REMOVE EGR HOLE COVER PLATE (w/o EGR System)
Remove the 4 nuts, 2 EGR hole plates and 2 gaskets from the intake manifold and exhaust manifold.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.
11409
27.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
23812D
28.REMOVE NO. 2 FUEL PIPE
Slide the clamp and disconnect the No. 1 fuel hose from the No. 2 fuel pipe.
Remove the bolt and No. 2 fuel pipe from the manifold stay.
29.REMOVE WIRING HARNESS CLAMP BRACKET
17118
30.REMOVE MANIFOLD STAY
22803
31.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY
23243B
32.REMOVE FUEL PUMP MOTOR WIRE
23273H
33.REMOVE NO. 2 FUEL HOSE
23271H
34.REMOVE NO. 1 FUEL HOSE
23804D
35.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)
23804D
36.REMOVE NO. 4 FUEL PIPE (w/ Pressurized Fuel Filter)
23815D
37.REMOVE NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)
23804C
38.REMOVE FUEL INLET PIPE SUB-ASSEMBLY
23770
39.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
17111
40.REMOVE INTAKE MANIFOLD
41.REMOVE WIRING HARNESS CLAMP BRACKET
23811H
42.REMOVE NO. 1 FUEL PIPE (w/ DPF)
23760
43.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY
44.REMOVE WIRING HARNESS CLAMP BRACKET
Remove the 2 bolts and 2 wiring harness clamp brackets from the cylinder head cover sub-assembly.
23701
45.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY
23810A
46.REMOVE COMMON RAIL ASSEMBLY
19871
47.REMOVE NO. 1 GLOW PLUG CONNECTOR
19850
48.REMOVE GLOW PLUG ASSEMBLY
44781
49.REMOVE HOSE BRACKET
Remove the 2 bolts and hose bracket from the cylinder head sub-assembly.
23300D
50.REMOVE DIESEL FUEL FILTER ASSEMBLY (w/ Pressurized Fuel Filter)
Remove the 2 nuts and diesel fuel filter assembly from the cylinder block sub-assembly.
23780B
51.REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/o Pressurized Fuel Filter)
Remove the 2 nuts and No. 3 nozzle leakage pipe from the cylinder block sub-assembly.
16025
52.REMOVE NO. 5 WATER BY-PASS PIPE SUB-ASSEMBLY
Remove the 3 bolts, No. 5 water by-pass pipe sub-assembly and gasket from the cylinder block sub-assembly.
for Laminated EGR Pre-cooler:
Remove the 4 bolts, No. 5 water by-pass pipe sub-assembly and gasket from the cylinder block sub-assembly.
88320
53.REMOVE COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
88431
54.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
Remove the 4 bolts and No. 1 compressor mounting bracket from the cylinder block sub-assembly, timing chain case assembly and timing chain cover sub-assembly.
16632B
55.REMOVE NO. 2 IDLER PULLEY BRACKET (w/o Air Conditioning System)
Remove the 3 bolts and No. 2 idler pulley bracket from the cylinder block sub-assembly, timing chain case assembly and timing chain cover sub-assembly.
89422P
56.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
12229
57.REMOVE PCV PIPE (for Cold Area Specification Vehicles)
16282
58.REMOVE NO. 5 WATER BY-PASS HOSE (w/ DPF)
Slide the 2 clamps and disconnect the No. 5 water by-pass hose from the No. 1 injector holder and water outlet sub-assembly.
Detach the clamp and remove the No. 5 water by-pass hose from the No. 1 water hose clamp bracket.
16281
59.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)
Slide the clamp and disconnect the No. 4 water by-pass hose from the No. 1 injector holder.
23295D
60.REMOVE NO. 1 INJECTOR HOLDER (w/ DPF)
89467B
61.REMOVE AIR FUEL RATIO SENSOR (w/o Nitrogen Oxides Sensor)
17167
62.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/ EGR Cooler)
17167
63.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/o EGR Cooler)
Remove the 3 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.
17271
64.REMOVE NO. 1 TURBO INSULATOR (w/ EGR Cooler)
17271
65.REMOVE NO. 1 TURBO INSULATOR (w/o EGR Cooler)
Remove the 3 bolts and No. 1 turbo insulator from the turbine outlet elbow and turbocharger sub-assembly.
89463C
66.DISCONNECT NO. 1 NITROGEN OXIDES SENSOR (w/ Nitrogen Oxides Sensor)
Detach the 4 clamps and disconnect the No. 1 nitrogen oxides sensor.
Remove the bolt and sensor bracket from the cylinder head sub-assembly.
67.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY (w/ EGR Cooler)
68.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY (w/o EGR Cooler)
Remove the bolt, 2 nuts and No. 2 exhaust pipe support stay from the cylinder block sub-assembly and turbine outlet elbow.
69.REMOVE EXHAUST PIPE SUPPORT STAY (w/ EGR Cooler)
70.REMOVE EXHAUST PIPE SUPPORT STAY (w/o EGR Cooler)
Remove the 3 bolts and exhaust pipe support stay from the cylinder block sub-assembly and turbine outlet elbow.
25051
71.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/ EGR Cooler)
17291
72.REMOVE TURBINE OUTLET ELBOW (w/o EGR Cooler)
Remove the nut, exhaust pipe clamp and turbine outlet elbow from the turbocharger sub-assembly.
Remove the gasket.
89463C
73.REMOVE NO. 1 NITROGEN OXIDES SENSOR (w/ Nitrogen Oxides Sensor)
12261
74.REMOVE PCV HOSE (except Cold Area Specification Vehicles)
16279
75.REMOVE NO. 3 WATER BY-PASS PIPE
76.REMOVE WATER BY-PASS HOSE (for Water Cooled Compressor Housing Turbocharger)
16268
77.REMOVE NO. 1 WATER BY-PASS PIPE
| *A | for Cold Area Specification Vehicles |
| *B | except Cold Area Specification Vehicles |
Remove the 3 bolts, No. 1 water by-pass pipe and gasket from the timing chain cover sub-assembly.
| *A | for Cold Area Specification Vehicles |
| *B | except Cold Area Specification Vehicles |
for Water Cooled Compressor Housing Turbocharger:
Remove the 3 bolts, No. 1 water by-pass pipe and gasket from the timing chain cover sub-assembly.
16284
78.DISCONNECT NO. 1 AND NO. 2 TURBO WATER HOSE
87101
79.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)
Remove the 4 bolts and No. 1 viscous heater bracket sub-assembly from the cylinder block sub-assembly and timing chain cover sub-assembly.
17293
80.REMOVE TURBOCHARGER STAY
15474
81.REMOVE TURBO OIL OUTLET PIPE
15407
82.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY
17201
83.REMOVE TURBOCHARGER SUB-ASSEMBLY
17141
84.REMOVE EXHAUST MANIFOLD
83530
85.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
16207
86.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Slide the clamp and disconnect the No. 3 water by-pass hose from the water outlet sub-assembly.
Remove the 2 bolts and No. 2 water by-pass pipe sub-assembly from the engine water pump assembly and water inlet.
16304
87.REMOVE WATER OUTLET SUB-ASSEMBLY
Remove the 4 bolts, 2 nuts and water outlet sub-assembly from the timing chain cover sub-assembly.
| *A | w/ DPF | *B | w/o DPF |
| *C | w/o EGR System | - | - |
Remove the gasket from the timing chain cover sub-assembly.
16321
88.REMOVE WATER INLET
Remove the 3 bolts and water inlet from the timing chain cover sub-assembly.
16331A
89.REMOVE THERMOSTAT
16603
90.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
16620
91.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
25706
92.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
| *A | w/ EGR System with EGR Cooler |
| *B | w/ EGR System without EGR Cooler |
w/ EGR System with EGR Cooler:
Disconnect the No. 1 vacuum transmitting hose from the vacuum pump assembly.
Remove the 3 bolts and No. 1 vacuum transmitting pipe sub-assembly from the cylinder head sub-assembly.
29300
93.REMOVE VACUUM PUMP ASSEMBLY
Remove the 3 bolts and vacuum pump assembly from the cylinder head sub-assembly.
Remove the 2 O-rings from the vacuum pump assembly.
11382C
94.REMOVE CAMSHAFT OIL SEAL RETAINER
Remove the camshaft oil seal retainer from the No. 3 camshaft bearing cap and cylinder head sub-assembly.
88451B
95.REMOVE VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)
13496
96.REMOVE CRANKSHAFT PULLY COVER (for Automatic Transmission)
13407
97.REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY (for Manual Transmission)
13471
98.REMOVE CRANKSHAFT PULLEY (for Automatic Transmission)
16575C
99.REMOVE NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)
Remove the bolt and No. 1 water hose clamp bracket from the timing chain case assembly.