Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1256/57    Accumulator Low Pressure

for Preparation Click here


DESCRIPTION

The accumulator pressure sensor is built into the actuator and detects the accumulator pressure.
The skid control ECU turns on the brake warning light / yellow (minor malfunction) and sounds the skid control buzzer if it senses a decrease in the accumulator pressure.
DTC C1256/57 may be output if the accumulator pressure drops due to frequent braking (this is not a malfunction).

DTC Code
INF Code
DTC Detection Condition
Trouble Area
C1256/57
141
Either of the following is detected:
  1. Braking operation signal is input when accumulator pressure is less than 12.45 MPa and vehicle speed signal is input (detected value changes if accumulator pressure is low after system start).
  2. Accumulator pressure is less than 14.62 MPa for 120 seconds (changes according to power source voltage) after system start (stores the DTC after the conditions are met, and sounds buzzer).
  1. Accumulator pressure
  2. Brake actuator assembly (Accumulator pressure sensor)
  3. Brake booster pump
↑
143
Any of the following is detected:
  1. Any of the wheel cylinder pressure sensor value is lower than the target value for at least 0.5 seconds when accumulator pressure is less than 14.62 MPa and vehicle speed signal is input.
  2. Accumulator pressure changes little when accumulator pressure is less than 14.62 MPa for at least 1 second without braking (pump motor is operating).
  3. Accumulator pressure is less than 14.62 MPa for at least 0.5 seconds when motor relay is malfunctioning.
↑

WIRING DIAGRAM

Refer to DTCs C1252/52 and C1253/53 .

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU or brake actuator assembly, perform initialization and calibration of the linear solenoid valve (Click here).

HINT:
When C1241/41, C1252/52 and/or C1253/53 are output together with C1256/57, inspect and repair the trouble areas indicated by C1241/41, C1252/52, C1253/53 and/or C1391/69 first (Click here, Click here, or Click here).

1.BRAKE PROBLEM CHECK
  1. Ask the customer if frequent braking was performed while the brake warning light / yellow (minor malfunction) was on.

    OK:

    Result
    Proceed to
    Frequent braking was performed
    A
    Frequent braking was not performed
    B

    HINT:
    This DTC is output even if the accumulator pressure drops only temporarily due to frequent braking.



B
END
A


2.INSPECT BRAKE BOOSTER PUMP
C150757E06
  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the brake booster pump connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B2 (BM1) - B4 (GND1)
    Always
    Below 10 Ω
    A2 (BM2) - B4 (GND1)
    Always
    Below 10 Ω
    B2 (BM1) - A2 (BM2)
    Always
    Below 1 Ω
    B4 (GND1) - A1 (GND2)
    Always
    Below 1 Ω
    B2 (BM1) - B1 (MTT)
    Always
    950 to 1050 Ω
    A2 (BM2) - B1 (MTT)
    Always
    950 to 1050 Ω



NG
REPLACE BRAKE BOOSTER PUMP (Click here)
OK


3.READ VALUE USING TECHSTREAM (ACCUMULATOR PRESSURE SENSOR)
  1. Reconnect the brake booster pump connectors.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the Data List mode on the Techstream (Click here).

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Accumulator Sensor
    Accumulator pressure sensor /
    min.: 0 V, max.: 5 V
    Specified value: 3.3 to 4.7 V
    -

  1. Depress the brake pedal 4 or 5 times to operate the pump motor, and check the output value on the Techstream with the motor stopped (not braking).

    OK:
    Accumulator pressure sensor output voltage does not drop.



NG
Go to step 5
OK


4.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Perform a road test.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTC (C1256/57) is not output
    A
    DTC (C1256/57) is output
    B



B
REPLACE SKID CONTROL ECU (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

5.READ VALUE USING TECHSTREAM (PRESSURE SENSOR)
  1. Select the Data List mode on the Techstream (Click here).


ABS / VSC / TRAC: 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Master Cylinder Sensor
Master cylinder pressure sensor 1 reading / min.: 0 V, max.: 5 V
When brake pedal is released: 0.3 to 0.9 V
Reading increases when brake pedal is depressed
Master Cylinder Sensor2
Master cylinder pressure sensor 2 reading / min.: 0 V, max.: 5 V
When brake pedal is released: 0.3 to 0.9 V
Reading increases when brake pedal is depressed
FR W/C Sensor
FR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V
When brake pedal is released: 0.3 to 0.9 V
-
FL W/C Sensor
FL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V
When brake pedal is released: 0.3 to 0.9 V
-
RR W/C Sensor
RR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V
When brake pedal is released: 0.3 to 0.9 V
-
RL W/C Sensor
RL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V
When brake pedal is released: 0.3 to 0.9 V
-
  1. Select the Active Test mode on the Techstream (Click here).

    HINT:
    The Active Test can be performed when the following conditions are met.
    1. ABS main relays 1 and 2 are on.
    2. Shift lever is in P.
    3. Parking brake is applied.
    4. Vehicle speed is 0 km/h (0 mph).


    ABS / VSC / TRAC: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ECB* Solenoid (SMC1)
    Master cut solenoid (SMC1)
    Solenoid ON / OFF
    Operation sound of solenoid (clicking sound) can be heard
    ECB* Solenoid (SMC2)
    Master cut solenoid (SMC2)
    Solenoid ON / OFF
    Operation sound of solenoid (clicking sound) can be heard
    ECB* Solenoid (SLRRL) Value Close
    Linear solenoid (SLRRL) valve
    Valve close ON / OFF
    -
    ECB* Solenoid (SLRRR) Value Close
    Linear solenoid (SLRRR) valve
    Valve close ON / OFF
    -
    *: Electronically Controlled Brake System

  1. Perform the Active Test of the solenoid using the Techstream.


C175403E01

  1. Check that the output value of each wheel cylinder does not increase.

    OK:
    The output value of each wheel cylinder does not increase.

    HINT:
    If any output value increases, there may be a brake fluid leak in the brake actuator.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK

REPLACE BRAKE BOOSTER PUMP (Click here)