Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge for 1AR-FE) › from 2016.11
RM3160E _53 Suspension _019689 FRONT SUSPENSION _0295250 FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge for 1AR-FE) A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge for 1AR-FE)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 5.REMOVE FRONT WHEELS

Hide 6.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 51441 8.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51442 9.REMOVE NO. 2 ENGINE UNDER COVER

Hide 58166 10.REMOVE FRONT FLOOR COVER LH

Hide 53876A 11.SEPARATE FRONT FENDER LINER LH

Hide 53875A 12.SEPARATE FRONT FENDER LINER RH

Hide 53737B 13.REMOVE FRONT FENDER APRON SEAL LH

Hide 53736 14.REMOVE FRONT FENDER APRON SEAL RH

Hide 53299D 15.REMOVE RADIATOR SIDE DEFLECTOR SEAL LH

Hide 53298E 16.REMOVE RADIATOR SIDE SEAL RH

Hide 53295E 17.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 12601B 18.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 17750A 19.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 17705 20.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 21.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 22.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 47220D 23.REMOVE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

a.
C292889C01
0.969,3.948 0.969,3.719 true 0.448,3.938 0.448,3.729 true 0.896,3.979 1.208,4.135 0.313,0.156 10 false *1 0.385,3.969 0.698,4.125 0.313,0.156 10 false *2
*1 Brake Master Cylinder Reservoir Assembly
*2 Reservoir Bracket


Disconnect the reservoir level switch connector and remove the bolt from the brake master cylinder reservoir assembly.


b.

Move the brake master cylinder reservoir assembly as shown in the illustration to disengage the 2 claws, and separate it.


Hide 82121 25.DISCONNECT ENGINE WIRE

a.
C370726

Disconnect the 3 wire clamps.


Hide 48810 26.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 27.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45220 28.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45470 29.SEPARATE TIE ROD ASSEMBLY LH

Hide 45460 30.SEPARATE TIE ROD ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48069 31.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 32.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 17410 33.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 12361 34.SEPARATE FRONT ENGINE MOUNTING INSULATOR

a.

Remove the hole plug.


b.
C365578

Remove the 3 nuts and separate the front engine mounting insulator from the front frame assembly.


Hide 12372A 35.SEPARATE ENGINE MOUNTING INSULATOR LH

a.

Remove the 2 hole plugs.


b.
C365579

Remove the 3 nuts and separate the engine mounting insulator LH from the front frame assembly.


Hide 12362 36.SEPARATE ENGINE MOUNTING INSULATOR RH

a.

Remove the 2 hole plugs.


b.
C365580

Remove the 3 nuts and separate the engine mounting insulator RH from the front frame assembly.


Hide 12327A 37.REMOVE NO. 2 ENGINE MOUNTING STAY RH

Hide 51100G 41.REMOVE FRONT FRAME ASSEMBLY

a.
C370732C01
0.979,1.063 1.729,1.063 false 0.823,0.969 1.135,1.125 0.313,0.156 10 false *a
*a Chain Block Assembly
V113147

Turn


Using the chain block assembly, lift the engine with automatic transaxle assembly until the engine is slightly raised off the front frame assembly.

NOTICE:
·

When suspending the engine with automatic transaxle assembly, do not tighten the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf).

·

Lift the engine with automatic transaxle assembly until the engine is slightly raised off the front frame assembly.

·

Do not lift the engine with automatic transaxle assembly excessively.

·

Do not shake the engine with automatic transaxle assembly excessively while it is suspended.




b.
C365584C01
0.24,1.292 0.313,1.292 0.313,1.292 0.396,0.823 false 0.823,0.646 0.823,1.073 0.823,1.073 1.594,1.073 true 1.479,1.073 1.479,0.594 true 2.042,0.573 2.052,1.115 2.052,1.115 3.188,1.115 true 2.75,1.115 2.75,0.615 true 0.073,1.198 0.385,1.354 0.313,0.156 10 false *a 1.635,0.99 1.948,1.146 0.313,0.156 10 false *b 3.229,1.031 3.417,1.198 0.188,0.167 10 false *b
*a Engine Lifter
*b Attachment
V100155

Attachment Placement Location


Support the front frame assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

CAUTION:
C342055

·

The front frame assembly is a very heavy component. Make sure that it is supported securely.

·

If the front frame assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:

Use attachments to keep the front frame assembly level.



c.
C365585C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 6 bolts, 2 nuts and frame side rail plate RH and frame side rail plate LH.


d.

Remove the 6 bolts, 2 nuts and front suspension member rear brace RH and front suspension member rear brace LH.


e.

Slowly lower the front frame assembly.

NOTICE:

When lowering the front frame assembly, be careful not to damage the vehicle body or other components installed to the vehicle.



Hide 48829A 42.REMOVE FRONT NO. 1 STABILIZER BRACKET LH

a.
C291634

Remove the 2 bolts and front No. 1 stabilizer bracket LH from the front frame assembly.


Hide 48824A 43.REMOVE FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.


Hide 44.REMOVE FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY

a.

Remove the front stabilizer bar with 2 front No. 2 stabilizer brackets, 2 front No. 1 stabilizer bar bushings and 2 front stabilizer link assemblies from the front frame assembly.


Hide 45.REMOVE STEERING LINK ASSEMBLY

a.
C366541

Remove the 2 bolts, 2 nuts and steering link assembly from the front frame assembly.

NOTICE:

Keep the nut from rotating while turning the bolt because the nut has its own stopper.



Hide 48069 46.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C292270

Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front frame assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 48068 47.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51227B 48.REMOVE FRONT SUSPENSION MEMBER DYNAMIC DAMPER

a.
C291641

Remove the 2 bolts and front suspension member dynamic damper from the front frame assembly.


Hide 52213A 49.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER

a.

Remove the 2 front suspension member body mounting front stoppers from the front frame assembly.


Hide 52216B 50.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER

a.

Remove the 2 front suspension member body mounting rear stoppers from the front frame assembly.


Hide 52211J 51.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION

a.
C267409C01
2.549,2.876 2.675,2.876 2.675,2.876 2.675,2.165 false 2.289,2.165 2.813,2.165 false 2.828,2.079 3.127,2.239 0.299,0.161 10 SST 1.907,0.875 2.348,0.875 false 2.373,0.795 2.672,0.956 0.299,0.161 10 SST 1.529,1.33 1.331,0.904 1.331,0.904 1.102,0.904 false 0.913,0.819 1.074,0.971 0.161,0.152 10 *1
*1 Front Suspension Member Body Mounting Front Cushion


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04011, 09958-04011)


b.
C265514C04
1.042,2.583 1.042,2.354 false 0.729,2.583 1.031,2.583 false 2.823,0.719 2.823,0.469 false 2.583,2.917 2.885,2.917 false 0.427,2.5 0.885,2.698 0.458,0.198 10 false SST 2.74,0.708 2.948,0.958 0.208,0.25 10 false *a 2.927,2.823 3.125,3.031 0.198,0.208 10 false *b
*a Turn
*b Hold


Using SST, remove each front suspension member body mounting front cushion from the front frame assembly.

NOTICE:
·

Make sure that the claws of SST are securely engaged to the mounting cushion.

·

Tighten SST slowly and evenly.

·

Be careful as the mounting cushion may fly out.

·

The mounting cushion cannot be reused.




Hide 52217E 52.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH

a.
C267410C01
2.266,2.213 2.754,2.213 false 2.549,2.898 2.635,2.898 2.635,2.898 2.635,2.213 false 2.783,2.125 3.082,2.291 0.298,0.166 10 SST 1.907,0.872 2.278,0.872 false 2.299,0.787 2.597,0.953 0.298,0.166 10 SST 1.538,1.343 1.357,0.87 1.357,0.87 1.007,0.87 false 0.818,0.782 0.979,0.947 0.162,0.166 10 *1
*1 Front Suspension Member Body Mounting Rear Cushion LH


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04011, 09958-04011)


b.
C265515C04
0.896,2.75 1.031,2.75 1.031,2.75 1.031,2.344 false 2.708,0.781 2.708,0.427 false 2.677,2.917 2.99,2.917 false 0.604,2.677 0.979,2.906 0.375,0.229 10 false SST 2.625,0.781 2.938,1.052 0.313,0.271 10 false *a 3.01,2.854 3.323,3.01 0.313,0.156 10 false *b
*a Turn
*b Hold


Using SST, remove the front suspension member body mounting rear cushion LH from the front frame assembly.

NOTICE:
·

Make sure that the claws of SST are securely engaged to the mounting cushion.

·

Tighten SST slowly and evenly.

·

Be careful as the mounting cushion may fly out.

·

The mounting cushion cannot be reused.




Hide 52215 53.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH

HINT:

Perform the same procedure as for the LH side.


Hide 54.REMOVE HOLE PLUG

a.

Remove the 14 hole plugs from the front frame assembly.

HINT:

There are 4 different shapes of hole plug.


C291647N01
3.604,0.052 3.76,0.25 0.156,0.198 10 false A 1.979,0.24 2.135,0.438 0.156,0.198 10 false A 1.792,0.417 1.948,0.615 0.156,0.198 10 false A 3.302,1.875 3.458,2.073 0.156,0.198 10 false A 3.771,1.885 3.927,2.083 0.156,0.198 10 false A 3.125,1.552 3.281,1.75 0.156,0.198 10 false A 4.052,1.646 4.208,1.844 0.156,0.198 10 false A 4.865,0.771 5.021,0.969 0.156,0.198 10 false A 3.427,1.635 3.583,1.833 0.156,0.198 10 false B 3.604,1.635 3.76,1.833 0.156,0.198 10 false B 4.5,0.292 4.656,0.49 0.156,0.198 10 false C 4.333,0.229 4.49,0.427 0.156,0.198 10 false C 1.813,1.958 1.969,2.156 0.156,0.198 10 false D 3.135,2.635 3.281,2.792 0.146,0.156 10 false D