Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function) › from 2016.11
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095461 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Engine does not Start  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. In addition, when the shift lever is in P and the brake pedal is depressed, the engine can be started by pressing the engine switch. If the steering is unlocked, the engine can also be started by pressing the engine switch with the shift lever in N and the brake pedal depressed.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Engine does not start
Power Source Control
·

Stop Light Switch1

·

Steering Unlock Switch

·

Shift P Signal

·

Neutral SW / Clutch SW

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)

·

Latch Circuit

·

Starter Request Signal

·

Power Supply Condition


Entry&Start
·

Immobiliser

·

Engine Start Request

·

S Code Check*

·

L Code Check


Starting Control
·

Starter SW

·

Shift Position P or N

·

Ignition



*: w/ Rear Seat Heater


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the smart entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to smart entry and start system (for Start Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION

·

After completing repairs, confirm that the problem does not recur.



HINT:
·

When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.

·

If the engine switch is turned from on (IG) to on (ACC) with the shift lever in any position other than P, then the shift lever is moved to P and the engine switch is pressed with the brake pedal depressed, the engine switch will be turned off.

·

If the brake pedal is repeatedly depressed while the engine is stopped, the brake booster pressure is released and the force required to depress the brake pedal to illuminate the stop lights increases.



PROCEDURE

1.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Press a switch of the electrical key transmitter sub-assembly.

OK:

The electrical key transmitter sub-assembly LED illuminates.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (KEY LOW BATTERY)

NG

11.INSPECT TRANSMITTER BATTERY
2.READ VALUE USING GTS (KEY LOW BATTERY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Low Battery Transmitter battery depleted No or Yes No: Transmitter battery not depleted
Yes: Transmitter battery depleted
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).
Body Electrical > Entry&Start > Data List
Tester Display
Key Low Battery
50003 125 23

Result:
Result Proceed to
"No" is displayed on the GTS screen A
"Yes" is displayed on the GTS screen B



A

3.CHECK WAVE ENVIRONMENT

B

3.CHECK WAVE ENVIRONMENT
a.

If the problem occurs in certain locations or times of day, the possibility of wave interference is high.

HINT:

Whether the problem is due to wave interference can be checked by holding the electrical key transmitter sub-assembly near the smart door control receiver assembly.


OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

4.CHECK ENGINE SWITCH CONDITION
4.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

With the brake pedal released, check that pressing the engine switch causes the power source mode to change.


Result:
Result Proceed to
Power source mode changes : Off → on (ACC) → on (IG) → off A
Power source mode does not change to on (ACC) or on (IG) B
Power source mode changes to on (IG) but not to on (ACC) C
Power source mode changes to on (ACC) but not to on (IG) D



A

5.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)

B

C

D

5.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control or Starting Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW Shift position (P and N) OFF or ON OFF: Shift lever in any position other than P or N
ON: Shift lever in P or N
·

Use this item to determine whether the park/neutral start switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral start switch assembly malfunction, OFF is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6
Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift Position P or N Park/Neutral position switch status OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
When malfunctioning, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Shift Position P or N
50003 221 2
OK:

The GTS display changes correctly in response to the shift position.



Result:
Proceed to
OK
NG



OK

6.CHECK FOR DTC

NG

24.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
6.CHECK FOR DTC
a.

Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Body Electrical > Power Source Control > Trouble Codes
50001 223
Body Electrical > Starting Control > Trouble Codes
50001 221

Result:
Result Proceed to
DTCs are not output A
Smart entry and start system (for Start Function) DTCs are output B



A

7.READ VALUE USING GTS (STOP LIGHT SWITCH1)

B

7.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

If the stop light switch is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The GTS display changes correctly in response to the brake operation.



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

21.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SUPPLY AND BODY GROUND)
8.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Engine start request signal status OFF or ON OFF: After approx. 1 second has elapsed, the engine switch is released
ON: With the shift lever in P and the brake pedal depressed, the engine switch is pressed and held
·

When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Starter Request Signal
50003 223 12
NOTICE:

Check that the key indicator is displayed on the multi-information display in the combination meter assembly, and then press the engine switch.


OK:

The GTS display changes correctly in response to the engine switch operation.



Result:
Proceed to
OK
NG



OK

9.CHECK STEERING LOCK

NG

12.READ VALUE USING GTS (STARTER SW)
9.CHECK STEERING LOCK
a.

Check that the steering unlocks when the engine switch is turned on (ACC).

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

10.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER SYSTEM UNSET)

NG

GO TO STEERING LOCK SYSTEM (UNABLE TO UNLOCK STEERING)

10.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER SYSTEM UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

Press the engine switch with the brake pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).

HINT:

The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).


OK:

The security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

11.INSPECT TRANSMITTER BATTERY
a.

Inspect the transmitter battery.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Smart Entry and Start System)>INSPECTION

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

12.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Starting Control / Data List.


e.

Read the Data List according to the display on the GTS.


f.

Get into the vehicle while carrying the electrical key transmitter sub-assembly, move the shift lever to P, press the engine switch while depressing the brake pedal and confirm that the GTS display changes.

Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter operation request OFF or ON OFF: Starter operation not requested
ON: Starter operation requested
When malfunctioning, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Starter SW
50003 221 1
OK:

The GTS display changes.



Result:
Proceed to
OK
NG



OK

13.INSPECT ST RELAY (STARTER RELAY ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

13.INSPECT ST RELAY (STARTER RELAY ASSEMBLY)
a.

Inspect the ST relay (starter relay assembly).

for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS STARTING>RELAY>ON-VEHICLE INSPECTION

for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE STARTING>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)

NG

REPLACE ST RELAY (STARTER RELAY ASSEMBLY)

14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)
a.
B340746C05
1.427,2.271 1.792,2.5 0.365,0.229 2.073,4.115 1.896,3.552 false 1.323,4.094 1.5,3.563 false 0.375,2.417 0.688,2.615 0.313,0.198 10 false *a 1.5,2.302 1.813,2.5 0.313,0.198 10 false F10 1.156,4.125 1.719,4.323 0.563,0.198 10 false STAR 1.958,4.135 2.521,4.333 0.563,0.198 10 false STA
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the F10 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A43 and C1 ECM connectors.


c.

Move the shift lever to P or N.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F10-10 (STAR) - Body ground 20°C (68°F) 107.05 to 116.33 Ω
F10-12 (STA) - Body ground 20°C (68°F) 106.78 to 115.98 Ω



Result:
Proceed to
OK
NG



OK

15.INSPECT STARTER ASSEMBLY

NG

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)
15.INSPECT STARTER ASSEMBLY
a.

Remove the starter assembly.

for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS STARTING>STARTER>REMOVAL

for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE STARTING>STARTER>REMOVAL


b.

Inspect the starter assembly.

for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS STARTING>STARTER>INSPECTION

for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE STARTING>STARTER>INSPECTION


Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY AND ST RELAY (STARTER RELAY ASSEMBLY)

NG

REPLACE STARTER ASSEMBLY

16.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY AND ST RELAY (STARTER RELAY ASSEMBLY)
a.

Disconnect the C18 and D2 starter assembly connectors.


b.

Remove the ST relay (starter relay assembly) from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D2-1(B) - Body ground Always 11 to 14 V
5 (ST relay (starter relay assembly)) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST relay (starter relay assembly)) - C18-1 (ST) Always Below 1 Ω
3 (ST relay (starter relay assembly)) or C18-1 (ST) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the F10 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the C14 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F10-10 (STAR) - C14-4 (B) Always Below 1 Ω
F10-10 (STAR) or C14-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY (STARTER RELAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY (STARTER RELAY ASSEMBLY)
a.

Disconnect the C14 park/neutral position switch assembly.


b.

Remove the ST relay (starter relay assembly) from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C14-9 (L) - 2 (ST relay (starter relay assembly)) Always Below 1 Ω
C14-9 (L) or 2 (ST relay (starter relay assembly)) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY (STARTER RELAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY (STARTER RELAY ASSEMBLY)
a.

Disconnect the F10 certification ECU (smart key ECU assembly) connector.


b.

Remove the ST relay (starter relay assembly) from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F10-12 (STA) - 2 (ST relay (starter relay assembly)) Always Below 1 Ω
F10-12 (STA) or 2 (ST relay (starter relay assembly)) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (ST RELAY (STARTER RELAY ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (ST RELAY (STARTER RELAY ASSEMBLY - BODY GROUND)
a.

Remove the ST relay (starter relay assembly) from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST relay (starter relay assembly)) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SUPPLY AND BODY GROUND)
a.
B331566C82
0.323,0.958 0.708,1.198 0.385,0.24 1.219,1.844 1.385,1.844 1.385,1.844 1.385,1.344 false 2.615,1.844 2.448,1.844 2.448,1.844 2.448,1.344 false 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a 0.896,1.771 1.292,1.99 0.396,0.219 10 false GND 0.396,1 0.792,1.219 0.396,0.219 10 false A87 2.656,1.76 3.052,1.979 0.396,0.219 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A87 stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A87-7 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A87-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the F10 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A87 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F10-2 (STP1) - A87-3 (L) Always Below 1 Ω
F10-2 (STP1) or A87-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the F10 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the C14 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F10-10 (STAR) - C14-4 (B) Always Below 1 Ω
F10-10 (STAR) or C14-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR