Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER (for HV Model)
RM37A0E _53 Suspension _086866 REAR SUSPENSION _0417444 REAR SUSPENSION MEMBER(for HV Model) A

REAR SUSPENSION  REAR SUSPENSION MEMBER(for HV Model)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL HOLE PLUG

a.
C336895

Install the 12 hole plugs to the rear suspension member sub-assembly as shown in the illustration.

HINT:

The upper and lower hole plug shapes are different.



Hide 2.INSTALL BOLT (for 2WD)

a.
C336896

Install the 2 bolts to the rear suspension member sub-assembly.

Torque:
86 N*m (877 kgf*cm, 63 ft.*lbf)


Hide 52271D 3.INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)

a.
C427662C01
0.042,0.042 0.344,0.271 0.302,0.229 10 false *a
*a View from Underneath
V100135

Front of the Vehicle
V100136

Outside of the Vehicle


Confirm the installation direction and temporarily install a new rear suspension member front body mounting cushion.

NOTICE:
·

Position the rear suspension member front body mounting cushion in the correct direction.

·

Do not apply lubricant to the outer sleeve of the rear suspension member front body mounting cushion.




b.
C202081N07
2.313,0.896 2.042,0.896 true 2.354,0.656 2.063,0.656 true 2.354,0.823 2.708,1.031 0.354,0.208 10 true SST 2.406,0.583 2.771,0.781 0.365,0.198 10 true SST

Install SST as shown in the illustration.

SST
09527-17011  
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.


HINT:

Use SST with the "F" mark facing the rear suspension member front body mounting cushion.



c.
C202082C04
1.427,0.76 1.083,0.76 true 1.448,0.979 1.26,0.979 false 0.781,0.667 1.094,0.854 0.313,0.188 10 false SST 0.979,0.896 1.302,1.094 0.323,0.198 10 false SST 2.167,1.813 2.479,2.01 0.313,0.198 10 false *a 2.583,1.135 2.896,1.333 0.313,0.198 10 false *b
*a Hold
*b Turn


Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.

SST
09527-17011  
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.



d.

Remove SST from the rear suspension member sub-assembly.


Hide 52271D 4.INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)

a.
C427663C01
0.083,0.063 0.396,0.219 0.313,0.156 10 false *a
*a View from Underneath
V100135

Front of the Vehicle
V100136

Outside of the Vehicle


Confirm the installation direction and temporarily install a new rear suspension member front body mounting cushion.

NOTICE:
·

Position the rear suspension member front body mounting cushion in the correct direction.

·

Do not apply lubricant to the outer sleeve of the rear suspension member front body mounting cushion.




b.
C203238N07
1.396,0.635 1.052,0.635 true 1.406,0.906 1.146,0.906 true 0.833,0.552 1.177,0.781 0.344,0.229 10 true SST 0.844,0.844 1.177,1.031 0.333,0.188 10 true SST

Install SST as shown in the illustration.

SST
09527-17011  
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.


HINT:

Use SST with the "F" mark facing the rear suspension member front body mounting cushion.



c.
C205621C05
1.479,0.792 1.167,0.792 true 1.479,0.979 1.25,0.979 true 0.885,0.719 1.229,0.906 0.344,0.188 10 true SST 0.969,0.917 1.26,1.104 0.292,0.188 10 true SST 2.333,1.927 2.646,2.083 0.313,0.156 10 false *a 2.979,1.01 3.292,1.167 0.313,0.156 10 false *b
*a Hold
*b Turn


Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.

SST
09527-17011  
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.



d.

Remove SST from the rear suspension member sub-assembly.


Hide 52276A 5.INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH

a.
C427659C01
0.104,0.052 0.417,0.365 0.313,0.313 10 false *a 3.021,1.521 3.333,1.719 0.313,0.198 10 false *b 1.229,1.51 1.542,1.708 0.313,0.198 10 false *b
*a View from Underneath
*b 15°
V100135

Front of the Vehicle
V100136

Outside of the Vehicle


Confirm the installation direction and temporarily install a new rear suspension member rear body mount cushion LH.

NOTICE:
·

Position the rear suspension member rear body mount cushion LH in the correct direction.

·

Do not apply lubricant to the outer sleeve of the rear suspension member rear body mount cushion LH.




b.
C199925N13
1.292,0.406 1.5,0.406 1.5,0.406 1.542,0.521 false 1.01,0.344 1.365,0.604 0.354,0.26 10 false SST

Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.


HINT:

Use SST with the "F" mark facing the rear suspension member rear body mount cushion LH.



c.
C199928C07
1.5,0.74 1.469,0.604 1.469,0.604 1.01,0.604 true 0.74,0.542 1.073,0.76 0.333,0.219 10 true SST 2.292,1.917 2.604,2.073 0.313,0.156 10 false *a 2.969,0.99 3.281,1.146 0.313,0.156 10 false *b
*a Hold
*b Turn


Using SST, install the rear suspension member rear body mount cushion LH until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mount cushion LH.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.



d.

Remove SST from the rear suspension member sub-assembly.


Hide 52275B 6.INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH

a.
C427660C01
0.104,0.063 0.417,0.219 0.313,0.156 10 false *a
*a View from Underneath
V100135

Front of the Vehicle
V100136

Outside of the Vehicle


Confirm the installation direction and temporarily install a new rear suspension member rear body mount cushion RH.

NOTICE:
·

Position the rear suspension member rear body mount cushion RH in the correct direction.

·

Do not apply lubricant to the outer sleeve of the rear suspension member rear body mount cushion RH.




b.
C199926N13
1.906,0.521 2.042,0.271 2.042,0.271 2.135,0.271 false 2.177,0.198 2.531,0.417 0.354,0.219 10 false SST

Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.


HINT:

Use SST with the "F" mark facing the rear suspension member rear body mount cushion RH.



c.
C199929C07
1.49,0.729 1.427,0.563 1.427,0.563 1.167,0.563 false 0.896,0.51 1.219,0.75 0.323,0.24 10 false SST 2.25,1.896 2.563,2.052 0.313,0.156 10 false *a 2.906,1.021 3.219,1.177 0.313,0.156 10 false *b
*a Hold
*b Turn


Using SST, install the rear suspension member rear body mount cushion RH until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mount cushion RH.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.



d.

Remove SST from the rear suspension member sub-assembly.


Hide 41651G 7.INSTALL DIFFERENTIAL MOUNT CUSHION (for 4WD/AWD)

a.
C426747C01
2.427,0.75 3.073,0.698 3.073,0.698 2.417,0.604 true 2.323,0.229 2.521,0.427 0.198,0.198 10 true *a 3.115,0.625 3.313,0.792 0.198,0.167 10 true *b
*a -3° to 3°
*b Protrusion
V100135

Front of the Vehicle


Temporarily install a new differential mount cushion to the rear suspension member sub-assembly from the rear of the vehicle as shown in the illustration.

NOTICE:
·

Make sure that the differential mount cushion is aligned within 3° from the center.

·

Install the differential mount cushion so that the protrusion is positioned as shown in the illustration.

·

Be sure to install the differential mount cushion in the correct direction.




b.

Using SST, press the differential mount cushion into the rear suspension member sub-assembly. (Step *1)

SST
09570-24011  

C426752C01
5.635,1.917 5.469,1.917 false 6.063,2.146 6.063,2.229 6.063,2.229 6.354,2.229 false 5.146,1.833 5.448,2.083 0.302,0.25 10 false SST 6.406,2.156 6.75,2.365 0.344,0.208 10 false SST 2.99,0.792 3.229,0.969 0.24,0.177 10 false *b 3.656,0.427 3.896,0.604 0.24,0.177 10 false *a
*a Hold *b Turn
V100136

Front of Vehicle
V100137

SST Bolt Position


NOTICE:
·

Apply molybdenum grease to the threads of the SST center bolt before use.

·

Be sure to install the SST bolt straight.




c.
C426753N01
1.292,0.521 1.292,0.354 1.292,0.354 1.01,0.354 false 2.281,0.625 2.094,0.625 false 2.583,0.188 2.75,0.417 0.167,0.229 10 false A 2.594,1.594 2.896,1.771 0.302,0.177 10 false B 0.729,0.271 1.031,0.479 0.302,0.208 10 false SST 1.823,0.542 2.135,0.802 0.313,0.26 10 false SST

Using a vernier caliper, measure the length indicated by (A) in the illustration. (Step *2)

NOTICE:
·

Measure at several points to ensure that the differential mount cushion is pressed in evenly.

·

Do not measure on a weld bead.




d.

Repeat the steps *1 and *2 to press the differential mount cushion into the rear suspension member sub-assembly until the length indicated by (A) in the illustration is within the specification.

Reference Length (A):

13.6 to 14.6 mm (0.535 to 0.575 in.)


HINT:

Reference length (A) = Standard length (B) + Thickness of SST



e.

Remove SST. Using a vernier caliper, measure the differential mount cushion protrusion length indicated by (B) in the illustration and ensure that the measured length is within the specification.

Standard Length (B):

7.6 to 8.6 mm (0.299 to 0.339 in.)



Hide 48790 8.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 9.INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 52272 10.INSTALL REAR SUSPENSION MEMBER UPPER STOPPER

a.

Install the 2 rear suspension member upper stoppers to the rear suspension member sub-assembly.


Hide 52278A 11.INSTALL REAR SUSPENSION MEMBER LOWER STOPPER RETAINER

a.

Install the 2 rear suspension member lower stopper retainers to the rear suspension member sub-assembly.


Hide G1050 12.INSTALL REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY (for 4WD/AWD)

Hide 51206A 13.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C426745C01
0.75,4.344 0.75,4.042 true 2.771,3.854 2.771,3.688 2.771,3.688 2.969,3.688 true 1.635,4.375 1.635,4.01 true 2.094,3.75 2.5,3.146 2.5,3.146 2.698,3.146 true 2.469,4.375 2.469,3.885 true 3.01,3.604 3.302,3.781 0.292,0.177 10 false *a 0.688,4.365 1.01,4.583 0.323,0.219 10 false *b 1.563,4.385 1.875,4.573 0.313,0.188 10 false *c 2.708,3.073 2.958,3.26 0.25,0.188 10 true *b 2.396,4.385 2.708,4.573 0.313,0.188 10 false *c
*a Engine Lifter
*b Attachment
*c Wooden Block
V100155

Attachment and Wooden Block Placement Location


Using an engine lifter, 2 attachments and 2 wooden blocks or equivalent tools, support the rear suspension member sub-assembly, and raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and vehicle body.

CAUTION:
C426744

·

The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:
·

Use attachments and wooden blocks to keep the rear suspension member sub-assembly level.

·

Keep supporting the rear suspension member sub-assembly until the installation has been completed.




b.

Install the rear suspension member sub-assembly with the 2 rear lower suspension braces, rear lower suspension member stopper LH and rear lower suspension member stopper RH, with the 4 bolts and 2 nuts.

C426746C01
0.49,1.521 0.49,1.292 0.49,1.292 0.656,1.292 false 6.625,1.531 6.625,1.302 6.625,1.302 6.49,1.302 false 0.406,1.552 0.708,1.74 0.302,0.188 10 false *1 6.542,1.573 6.854,1.729 0.313,0.156 10 false *1
*1 Rear Lower Suspension Brace - -


Torque:
Bolt : 158 N*m (1611 kgf*cm, 117 ft.*lbf)
Nut : 32 N*m (326 kgf*cm, 24 ft.*lbf)

NOTICE:

Be sure to install the rear suspension member sub-assembly with the rear lower suspension braces facing in the correct direction as shown in the illustration.



Hide 821H1 14.CONNECT FLOOR UNDER WIRE (for 4WD/AWD)

CAUTION:

Be sure to wear insulated gloves.


a.
A455864C01
2.594,3.104 2.208,3.104 2.208,3.104 1.896,2.708 true 2.646,3 2.958,3.198 0.313,0.198 10 false *a
*a Waterproof Seal


Install the HV floor under wire to the rear traction motor with transaxle assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:
·

Make sure that the connector is fully engaged.

·

Do not damage the terminals, interlock connector or rear traction motor with transaxle assembly during installation.

·

Do not touch the waterproof seal or terminals of the connector.

·

Do not allow any foreign matter or water to enter the rear traction motor with transaxle assembly.

·

Although the connector may feel loose, this is not due to a malfunction.




b.
A455863

Engage the clamp.


Hide 82164 15.INSTALL FRAME WIRE (for 4WD/AWD)

a.

Install the frame wire to the rear suspension member sub-assembly with the bolt and clamp.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Install the frame wire to the rear traction motor with transaxle assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the 2 connectors.


Hide 42341C 16.INSTALL REAR DRIVE SHAFT LH SNAP RING (for 4WD/AWD)

Hide 42341B 17.INSTALL REAR DRIVE SHAFT RH SNAP RING (for 4WD/AWD)

HINT:

Perform the same procedure as for the LH side.


Hide 42340B 18.INSTALL REAR DRIVE SHAFT ASSEMBLY LH (for 4WD/AWD)

Hide 42330 19.INSTALL REAR DRIVE SHAFT ASSEMBLY RH (for 4WD/AWD)

HINT:

Perform the same procedure as for the LH side.


Hide 48790 20.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

a.
C426738

Using a brass bar and a hammer, push out the bushing until it is positioned as shown in the illustration.

HINT:

Pushing out the bushing makes it easier to connect the rear upper control arm assembly LH.



b.
C426727

Temporarily install the rear axle carrier sub-assembly to the rear upper control arm assembly with the bolt and nut.

NOTICE:
·

Insert the bolt with the threaded end facing the rear of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.




Hide 48770A 21.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 22.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 23.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48740F 24.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 25.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48258C 26.INSTALL REAR LOWER COIL SPRING INSULATOR LH

Hide 48258B 27.INSTALL REAR LOWER COIL SPRING INSULATOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 48231B 28.INSTALL REAR COIL SPRING LH

Hide 48231A 29.INSTALL REAR COIL SPRING RH

HINT:

Perform the same procedure as for the LH side.


Hide 48835 30.INSTALL REAR LOWER STABILIZER BRACKET

Hide 48812 31.INSTALL REAR STABILIZER BAR

Hide 32.TEMPORARILY INSTALL REAR STABILIZER LINK ASSEMBLY LH

Hide 33.TEMPORARILY INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 89544E 34.INSTALL REAR SKID CONTROL SENSOR LH (for 4WD/AWD)

Hide 89544D 35.INSTALL REAR SKID CONTROL SENSOR RH (for 4WD/AWD)

HINT:

Perform the same procedure as for the LH side.


Hide 890C0A 36.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY (for 4WD/AWD)

a.

Connect the No. 2 parking brake wire assembly connector to the rear skid control sensor.


Hide 890C0 37.CONNECT NO. 1 PARKING BRAKE WIRE ASSEMBLY (for 4WD/AWD)

HINT:

Perform the same procedure as for the LH side.


Hide 42312B 38.INSTALL REAR AXLE SHAFT NUT LH (for 4WD/AWD)

Hide 42311N 39.INSTALL REAR AXLE SHAFT NUT RH (for 4WD/AWD)

HINT:

Perform the same procedure as for the LH side.


Hide 47319F 40.CONNECT REAR FLEXIBLE HOSE LH

a.
C424684

Connect the rear flexible hose LH to the rear upper control arm assembly LH with the bolt.

Torque:
18.8 N*m (192 kgf*cm, 14 ft.*lbf)


Hide 47318F 41.CONNECT REAR FLEXIBLE HOSE RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 43.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 44.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48740F 45.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.

Install the rear No. 2 suspension arm assembly LH (rear axle carrier sub-assembly side) with the bolt.

Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION


Hide 48730F 46.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 47.INSTALL REAR STABILIZER LINK ASSEMBLY LH

Hide 48.INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48790 49.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

a.

Install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48770A 50.INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48738 51.INSTALL REAR SUSPENSION ARM COVER LH

Hide 48737 52.INSTALL REAR SUSPENSION ARM COVER RH

HINT:

Perform the same procedure as for the LH side.


Hide G3834 54.INSTALL SERVICE PLUG GRIP (for 4WD/AWD)

Hide 55.INSTALL REAR WHEEL

Hide 48740F 56.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.

Install the rear No. 2 suspension arm assembly LH (rear suspension member sub-assembly side) with the nut.

Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION


Hide 48730F 57.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 58.ADD HYBRID TRANSAXLE FLUID (for 4WD/AWD)

Hide 59.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK (for 4WD/AWD)

Hide 61.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 63.PERFORM INITIALIZATION

Parking Support Brake System (Click here)
Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)