Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0419999 HV BATTERY A

HYBRID / BATTERY CONTROL  HV BATTERY  INSTALLATION  


PROCEDURE

Hide G92Z2 3.INSTALL HYBRID BATTERY TERMINAL BLOCK

Hide G920Q 4.INSTALL NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

Hide 5.INSTALL HV BATTERY JUNCTION BLOCK ASSEMBLY

Hide G92QC 6.INSTALL NO. 10 HV BATTERY SHIELD PANEL

a.

Install the No. 10 HV battery shield panel to the HV battery with the 6 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide G9510 7.INSTALL HV BATTERY

CAUTION:

Be sure to wear insulated gloves.


a.
A455552

Set wooden blocks as shown in the illustration.


b.

Using a suitable adaptor such as straps, install the HV battery while tilting it.

CAUTION:

To prevent any accidents and injuries due to the weight of the HV battery, follow all specified procedures and be careful to balance the HV battery when removing or installing it.


NOTICE:
·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

Use cardboard or another similar material to protect the HV battery and vehicle body from damage.

·

Since the HV battery is very heavy, 2 people are needed to install it. When installing the HV battery, be careful not to damage the parts around it.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

While lowering the HV battery into the vehicle, do not allow it to contact the vehicle.

·

If the HV battery has been struck or dropped, replace it.




c.
A455553

Push the HV battery to the front of the vehicle as shown in the illustration.


d.

Install the No. 2 HV battery intake duct RH to the HV battery with the clip.


e.

Engage the 2 claws of hybrid battery thermistor (sensor portion) to connect the hybrid battery thermistor to the No. 2 HV battery intake duct RH.


f.

Engage the clamp.


g.

Install the No. 2 HV battery intake duct LH to the HV battery with the clip.


h.
A455554

Tilt the HV battery and remove the wooden blocks.


i.
A455543C01
0.906,0.458 1.063,0.656 0.156,0.198 10 true *b 1.365,2.615 1.521,2.813 0.156,0.198 10 true *a 2.719,0.469 2.875,0.667 0.156,0.198 10 true *b 0.938,2.01 1.094,2.208 0.156,0.198 10 true *b 2.677,1.979 2.833,2.177 0.156,0.198 10 true *b 2.229,2.615 2.385,2.813 0.156,0.198 10 true *a 1.146,2.792 1.302,2.99 0.156,0.198 10 false 2 2.177,2.771 2.333,2.969 0.156,0.198 10 false 1
*a Bolt (A)
(Bolt Length: 24 mm (0.945 in.))
*b Bolt (B)
(Bolt Length: 25 mm (0.984 in.))


Temporarily install the HV battery to the vehicle body with the 2 bolts (A) and 4 bolts (B).

NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

As bolts with 2 different lengths are used, make sure to install each bolt to the correct position.




j.

Fully tighten the 2 bolts (A) in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


k.

Fully tighten the 4 bolts (B).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide G92QC 8.REMOVE NO. 10 HV BATTERY SHIELD PANEL

Hide 82161 9.CONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Engage the 3 clamps to connect the floor wire.


b.

Connect the electric vehicle battery plug assembly connector.


c.

Connect the HV battery junction block assembly connector.

NOTICE:

Make sure that the connector is connected securely.



d.

Connect the floor wire connector.


e.

Engage the 2 clamps.


Hide 821H1 10.CONNECT FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Connect the shield ground to the HV battery.


b.

Engage the clamp.


c.

Connect the 2 HV battery junction block assembly connectors.

NOTICE:

Make sure that the connectors are connected securely.



Hide G92QC 11.INSTALL NO. 10 HV BATTERY SHIELD PANEL

CAUTION:

Be sure to wear insulated gloves.


a.
A456338C01
0.854,0.375 1,0.375 1,0.375 1.115,0.542 true 1.375,0.635 1.635,0.635 false 1.646,0.542 1.958,0.698 0.313,0.156 10 false *1 0.688,0.271 1,0.427 0.313,0.156 10 false *a 0.427,0.542 0.74,0.698 0.313,0.156 10 false *b
*1 Battery Cover Lock Striker
*a Button
*b Push


Install the No. 10 HV battery shield panel to the HV battery with the 6 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Install the battery cover lock striker, then push the button to lock it.


Hide 73530E 12.INSTALL REAR SEAT SUB FLOOR PANEL ASSEMBLY

a.

Install the rear seat sub floor panel assembly with the 6 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


b.

Connect the connector.


Hide 74865D 13.INSTALL CENTER PROTECTOR COVER

a.
A456362N01
1.302,0.677 1.458,0.875 0.156,0.198 10 true A 1.823,0.677 1.979,0.875 0.156,0.198 10 true A 2.344,0.677 2.5,0.875 0.156,0.198 10 true A 2.479,1.26 2.635,1.458 0.156,0.198 10 true B 1.927,1.219 2.083,1.417 0.156,0.198 10 true B 1.385,1.229 1.542,1.427 0.156,0.198 10 true B 0.833,1.26 0.99,1.458 0.156,0.198 10 true B

Install the center protector cover with the 4 clips (B).


b.

Install the 3 clips (A).


Hide 64713F 14.INSTALL FRONT DECK SIDE TRIM COVER LH

Hide 64712F 15.INSTALL FRONT DECK SIDE TRIM COVER RH

Hide 16.INSTALL REAR NO. 2 SEAT ASSEMBLY

Hide 65341 17.INSTALL NO. 1 FLOOR BOARD

a.

Install the No. 1 floor board.


Hide 65342 18.INSTALL NO. 2 FLOOR BOARD

a.

Install the No. 2 floor board.


Hide 65343 19.INSTALL NO. 3 FLOOR BOARD

a.

Install the No. 3 floor board.


Hide G9230 20.INSTALL BATTERY COOLING BLOWER ASSEMBLY

Hide 22.PERFORM INITIALIZATION