Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › FRAME WIRE
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420003 FRAME WIRE A

HYBRID / BATTERY CONTROL  FRAME WIRE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during HV floor under wire removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking Support Brake System*1
Pre-collision System
Lighting System (EXT) (w/ AFS)
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Replacement of air fuel ratio sensor (sensor 1)

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>PRECAUTION

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A344817

The fuel tank sub-assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank sub-assembly may fall off the engine lifter.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 82111 3.DISCONNECT ENGINE ROOM MAIN WIRE

CAUTION:

Be sure to wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.
A451917

Move the lock lever while pushing the lock on the connector, and disconnect the inverter with converter assembly connector.

NOTICE:
·

Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.

·

Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.

·

Insulate the disconnected terminals with insulating tape.

·

Do not touch the waterproof seal or terminals of the connector.




Hide 6.TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY

Hide 10.REMOVE REAR NO. 2 SEAT ASSEMBLY

Hide 64712F 11.REMOVE FRONT DECK SIDE TRIM COVER RH

Hide 73360D 12.DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT BELT>REAR NO. 1 SEAT OUTER BELT ASSEMBLY>REMOVAL


Hide 64714H 13.REMOVE NO. 1 DECK SIDE TRIM COVER

HINT:

Use the same procedure as for the No. 2 deck side trim cover.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 73560 14.DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT OUTER BELT ASSEMBLY>REMOVAL


Hide 88625T 15.REMOVE COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR

Hide 64974 16.REMOVE DECK TRIM POCKET COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 64725F 17.REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 66311 18.REMOVE ROPE HOOK (for RH Side)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 64730B 19.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

Hide 821H1 20.DISCONNECT FLOOR UNDER WIRE

a.
A455860

Disengage the 2 clamps.


b.

Remove the nut to disconnect the HV floor under wire.


Hide 58510D 21.SEPARATE FRONT FLOOR CARPET ASSEMBLY

Hide 58556C 22.REMOVE REAR FLOOR SILENCER

Hide G92QC 23.REMOVE NO. 10 HV BATTERY SHIELD PANEL

Hide 821H1 24.DISCONNECT FLOOR UNDER WIRE

Hide 17410 25.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 77001A 27.REMOVE FUEL TANK SUB-ASSEMBLY

Hide 58720B 29.REMOVE ENGINE SERVICE COVER ASSEMBLY

a.
A455857

Remove the 3 nuts, clip and engine service cover assembly.


Hide 17573A 30.REMOVE NO. 3 EXHAUST PIPE SUPPORT BRACKET

a.
A455855

Remove the 2 bolts and No. 3 exhaust pipe support bracket.


Hide 17574 31.REMOVE NO. 4 EXHAUST PIPE SUPPORT BRACKET

a.
A455856

Remove the 2 bolts and No. 4 exhaust pipe support bracket.


Hide 58043 32.REMOVE REAR MAIN MUFFLER HEAT INSULATOR SUB-ASSEMBLY

a.
A455858

Remove the 3 nuts and rear main muffler heat insulator sub-assembly.


Hide 58151 33.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

a.
A455859

Remove the 3 nuts and front No. 1 floor heat insulator.


Hide 821H1 34.REMOVE FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


NOTICE:

Insulate the disconnected connectors with insulating tape.


a.
A455874

Remove the nut and disconnect the transmission control cable assembly.


b.
A455875

Remove the 2 nuts and bolt to disconnect the air conditioning tube assembly.


c.
A455861

Remove the 2 nuts.


d.

for 4WD/AWD:

i.
A455862

Remove the nut and clamp.


ii.
A455863

Disengage the clamp.


iii.
A455864C01
2.594,3.104 2.208,3.104 2.208,3.104 1.896,2.708 true 2.646,3 2.958,3.198 0.313,0.198 10 false *a
*a Waterproof Seal


Remove the 2 bolts and HV floor under wire from the rear traction motor with transaxle assembly.

NOTICE:
·

Do not damage the terminals, interlock connector or rear traction motor with transaxle assembly during disconnection.

·

Do not touch the waterproof seal or terminals of the connector.

·

Do not allow any foreign matter or water to enter the rear traction motor with transaxle assembly.

·

Although the connector may feel loose, this is not due to a malfunction.





e.
A455865C01
2.802,1.729 2.875,1.552 2.875,1.552 2.99,1.552 true 3.01,1.469 3.167,1.625 0.156,0.156 10 true *a
*a Grommet


Remove the nut and clamp.

NOTICE:

If the clamp is removed forcibly, the stud bolt may be damaged.



f.

Disengage the grommet and pull out the HV floor under wire from the floor panel hole.


g.
A455866

Remove the 3 nuts and clamp.

NOTICE:

If the clamp is removed forcibly, the stud bolt may be damaged.



h.
A455867

Remove the nut, bolt and clamp.

NOTICE:

If the clamp is removed forcibly, the stud bolt may be damaged.



i.
A455868

Disengage the grommet and pull out the HV floor under wire from the floor panel hole.


j.
A455869

Remove the 2 nuts, bolt and 2 clamps.

NOTICE:

If the clamps are removed forcibly, the stud bolts may be damaged.



k.
A455870

Disengage the 2 claws.


l.

Disengage the guide to remove the No. 1 terminal cap.


m.
A455871

Remove the nut.


n.

Disengage the 2 claws to disconnect the engine room main wire.


o.
A455872

Remove the 2 nuts and HV floor under wire.