Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2020.11
RM37A0E _55 Steering _086874 POWER ASSIST SYSTEMS _0419667 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1581  Assist Map Number Un-Writing  


DESCRIPTION

This DTC will be stored if the power steering ECU (rack and pinion power steering gear assembly) determines that the assist map is not written in the ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1581 Assist Map Number Un-Writing Assist map not written in power steering ECU (rack and pinion power steering gear assembly)
for Gasoline Model:
·

CAN communication system

·

ECM

·

Main body ECU (Multiplex network body ECU)

·

Skid control ECU (Brake actuator assembly)

·

Rack and pinion power steering gear assembly


for HV Model:
·

CAN communication system

·

Hybrid vehicle control ECU

·

Main body ECU (Multiplex network body ECU)

·

No. 2 skid control ECU (Brake actuator assembly)

·

Rack and pinion power steering gear assembly


EPS warning light: Comes on Assist Map Writing is performed -

CAUTION / NOTICE / HINT

NOTICE:

If the rack and pinion power steering gear assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


HINT:

Related parts store information necessary for assist map writing.

Related Part:

for Gasoline Model:
·

ECM

·

Main body ECU (Multiplex network body ECU)

·

Skid control ECU (Brake actuator assembly)


for HV Model:
·

Hybrid vehicle control ECU

·

Main body ECU (Multiplex network body ECU)

·

No. 2 skid control ECU (Brake actuator assembly)



PROCEDURE

1.PERFORM ASSIST MAP WRITING
a.

Perform assist map writing.

Chassis > EMPS > Utility
Tester Display
Signal Check
50005 142 3

b.

Check for DTCs.

Chassis > EMPS > Trouble Codes
50001 142
Result:
Result Proceed to
DTC C1581 is output. A
DTC C1581 is not output. B




A

2.CHECK CAN COMMUNICATION SYSTEM

B

END

2.CHECK CAN COMMUNICATION SYSTEM

Result:
Result Proceed to
CAN communication system DTCs are not output. (for Gasoline Model) A
CAN communication system DTCs are not output. (for HV Model) B
CAN communication system DTCs are output. C



A

3.CHECK RELATED PART

B

7.CHECK RELATED PART

C

3.CHECK RELATED PART
a.

Confirm if the related part has the correct part number.

Related Part ECM
Main body ECU (Multiplex network body ECU)
Skid control ECU (Brake actuator assembly)

NOTICE:

When removing the related part to check it, be sure to follow the appropriate procedures and precautions.




Result:
Result Proceed to
The related part has the correct part number. A
The related part has an incorrect part number. B



A

4.CHECK FOR DTC

B

5.REPLACE RELATED PART WITH PART THAT HAS CORRECT PART NUMBER
4.CHECK FOR DTC
a.

Select Health Check on the GTS screen and check if system DTCs of the related part are output.

HINT:

If system DTCs of the related part are stored, assist map writing to the power steering ECU (rack and pinion power steering gear assembly) may not be performed properly.



Result:
Result Proceed to
System DTCs of the related part are output. A
System DTCs of the related part are not output. B



A

REPAIR CIRCUIT INDICATED BY OUTPUT CODE

B

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

5.REPLACE RELATED PART WITH PART THAT HAS CORRECT PART NUMBER
a.

Replace the related part with one that has the correct part number.



Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Chassis > EMPS > Trouble Codes
50001 142

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

END

B

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

7.CHECK RELATED PART
a.

Confirm if the related part has the correct part number.

Related Part Hybrid vehicle control ECU
Main body ECU (Multiplex network body ECU)
No. 2 skid control ECU (Brake actuator assembly)

NOTICE:

When removing the related part to check it, be sure to follow the appropriate procedures and precautions.




Result:
Result Proceed to
The related part has the correct part number. A
The related part has an incorrect part number. B



A

8.CHECK FOR DTC

B

9.REPLACE RELATED PART WITH PART THAT HAS CORRECT PART NUMBER
8.CHECK FOR DTC
a.

Select Health Check on the GTS screen and check if system DTCs of the related part are output.

HINT:

If system DTCs of the related part are stored, assist map writing to the power steering ECU (rack and pinion power steering gear assembly) may not be performed properly.



Result:
Result Proceed to
System DTCs of the related part are output. A
System DTCs of the related part are not output. B



A

REPAIR CIRCUIT INDICATED BY OUTPUT CODE

B

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

9.REPLACE RELATED PART WITH PART THAT HAS CORRECT PART NUMBER
a.

Replace the related part with one that has the correct part number.



Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Check for DTCs.

Chassis > EMPS > Trouble Codes
50001 142

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

END

B

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY