Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (ENGINE MECHANICAL) › ENGINE UNIT › from 2021.10
RM37A0E _51 Engine / Hybrid System _086906 A25A-FXS, A25B-FXS ENGINE MECHANICAL _0418985 ENGINE UNIT A

A25A-FXS, A25B-FXS ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed or replaced during engine unit removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*2: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*3: If the vehicle height has changed due to suspension or tire replacement

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) registration DTC is output (Click here)
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body assembly

·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Replacement of knock control sensor


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


for 2WD:(Click here)
for 4WD/AWD:(Click here)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Replacement of front bumper assembly*2
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic View Monitor System (Click here)
Suspension, tires, etc.*3
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Front wheel alignment adjustment Perform "Calibration".
·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 43457 1.REMOVE DRIVE SHAFT BEARING BRACKET

a.
A406682

Remove the 3 bolts and drive shaft bearing bracket.


Hide 88370 2.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY

a.
E371430C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt and 2 nuts.


b.
E371431

Using an E8 "TORX" socket wrench, remove the 2 stud bolts and compressor with motor assembly.


Hide 16207 3.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A455166

Slide the clip and disconnect the No. 2 water by-pass pipe sub-assembly from the water by-pass outlet.


b.

Remove the bolt and the No. 2 water by-pass pipe sub-assembly.


Hide 16260 4.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

a.
A455167

Remove the bolt.


b.
A455168

Slide the clip and remove the flow shutting valve (water by-pass hose assembly) from the water by-pass outlet.


c.
A455171

Remove the 2 bolts and water hose clamp bracket.


Hide 89481B 5.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ Differential Pressure Sensor)

Hide 25706 6.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ Differential Pressure Sensor)

a.
A450073

Remove the nut.


b.
A450074

Using a 14 mm union nut wrench, remove the No. 1 vacuum transmitting pipe sub-assembly from the exhaust manifold.


Hide 17167 7.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

w/o Differential Pressure Sensor:

i.
A404785

Remove the 5 bolts and the No. 1 exhaust manifold heat insulator from the exhaust manifold.



b.

w/ Differential Pressure Sensor:

i.
A450072

Remove the 3 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.



Hide 17141 9.REMOVE EXHAUST MANIFOLD

a.
A406687

Using a 12 mm deep socket wrench, remove the 7 nuts and remove the exhaust manifold from the cylinder head sub-assembly.


b.
A406688

Remove the exhaust manifold to head gasket from the cylinder head sub-assembly.


Hide 22030 10.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25601 13.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 16279 15.REMOVE NO. 3 WATER BY-PASS PIPE

a.
A406695

Using an 8 mm socket wrench, remove the bolt and disconnect the No. 3 water by-pass pipe from the intake manifold.


b.

Slide the clip and remove the No. 3 water by-pass pipe from the water outlet.


Hide 16278 16.REMOVE NO. 2 WATER BY-PASS PIPE

a.
A473529N01
1.698,1.052 1.854,1.25 0.156,0.198 10 true B 1.083,1.667 1.24,1.865 0.156,0.198 10 true B 2.49,1.917 2.646,2.115 0.156,0.198 10 true A

Remove the bolt (A).


b.

Using an 8 mm socket wrench, remove the 2 bolts (B) and No. 2 water by-pass pipe.


Hide 17177 18.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 23801P 20.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A471089

Using an 8 mm socket wrench, remove the bolt.


b.

Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.


Hide 23100X 21.REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 16295 22.REMOVE NO. 7 WATER BY-PASS HOSE

a.
A406697

Slide the 2 clips and remove the No. 7 water by-pass hose.


Hide 82219A 23.REMOVE SENSOR WIRE

a.
A476332

Disconnect the 3 connectors.


b.

Disengage the 3 clamps.


c.

Using an 8 mm socket wrench, remove the bolt and sensor wire from the water inlet with thermostat sub-assembly.


Hide 82126A 24.REMOVE NO. 6 ENGINE WIRE

a.
A406699

Disconnect the 4 connectors.


b.

Disengage the 2 clamps.


c.

Remove the 2 nuts and No. 6 engine wire from the wire harness clamp bracket.


Hide 25.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A406700

Using an 8 mm socket wrench, remove the 2 bolts and wire harness clamp bracket from the No. 1 ventilation case.


Hide 11452 34.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Remove the engine oil level dipstick.


b.
A400314

Using an 8 mm socket wrench, remove the bolt and engine oil level dipstick guide from the camshaft housing sub-assembly.


c.
A400321

Remove the O-ring from the engine oil level dipstick guide.


Hide 17169A 35.REMOVE NO. 3 EXHAUST MANIFOLD HEAT INSULATOR

a.
A455172

Remove the bolt and No. 3 exhaust manifold heat insulator from the cylinder block sub-assembly.