Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (FUEL) › FUEL PRESSURE SENSOR › from 2021.10
RM37A0E _51 Engine / Hybrid System _086907 A25A-FXS, A25B-FXS FUEL _0417785 FUEL PRESSURE SENSOR A

A25A-FXS, A25B-FXS FUEL  FUEL PRESSURE SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during No. 2 fuel pressure sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


for 2WD:(Click here)
for 4WD/AWD:(Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) registration DTC is output (Click here)
·

Replacement of No. 2 fuel pressure sensor

·

Replacement of fuel pump assembly

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A357489

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.



NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 58441L 3.REMOVE BATTERY SERVICE HOLE COVER

Hide 4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 22030 5.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25715 7.REMOVE EMISSION CONTROL VALVE BRACKET (w/ Differential Pressure Sensor)

Hide 23100X 11.REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY

Hide 89458H 12.REMOVE NO. 2 FUEL PRESSURE SENSOR

a.
A428394

Disconnect the No. 2 fuel pressure sensor connector.


b.
A428395

Using an 8 mm socket wrench, remove the bolt, No. 2 fuel pressure sensor and No. 2 fuel pressure sensor holder from the fuel delivery pipe sub-assembly.


c.
A427249

Remove the O-ring from the No. 2 fuel pressure sensor.