2014 Hilux · Service Manual ENGINE

Engine Difficult to Start or Stalling

Circuit diagnosis · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION


Faults and Symptoms of Common Rail Diesel Components
  1. Engine Control

    Mass Air Flow Meter 
    Main fault
    Decrease in performance (foreign matter is stuck)
    Symptoms
    Lack of power, black smoke
    Data List
    MAF

    HINT:
    The maximum fuel injection volume is controlled according to the output from the mass air flow meter.

    Intake System 
    Symptom: Main fault
    1. Lack of power (No black smoke): air filter blockage, air duct is crushed/leaking
    2. Black smoke (No lack of power): Leakage between the turbo and intake manifold
    Data List
    1. MAP (inside intake air pressure)
    2. Target Booster Pressure
      When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt.
    Turbocharger System 
    Main fault
    1. Air leak in the turbocharged air passage
    2. Turbo motor driver not operating well
    3. Turbocharger (turbine, bearing)
    Symptoms
    Lack of power (when vehicle starting, when heavy load)
    (Black smoke is not emitted when racing while vehicle stopped)
    Data List
    MAP (inside intake air pressure), Target Booster Pressure
    1. When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt.
    2. With the ignition switch ON or during idling, MAP = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure.
    3. Atmospheric pressure decreases 1 kPa each time altitude increases by 100 m, and is also affected by the current weather conditions.
    VN Turbo Command
    1. 0%: Vanes fully open (drive rod contracts)
    2. Over 90%: Vanes fully closed (drive rod expands and turbo operates effectively)
    Diagnostic Point
    1. Using the Active Test "Test the Turbo Charger Step Motor", check the drive rod movement.
    2. Check the drive rod movement when the ignition switch is turned from ON to off.
    Exhaust System 
    Main fault
    Blockage
    Symptoms
    Lack of power (high engine speed, when heavy load)
    Data List
    MAP (inside intake air pressure)
    When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt.
    Glow System 
    Main fault
    Open circuit, glow plug relay fault
    Symptoms
    Difficult to start, rough idle, knocking, white smoke (when cold)
    Data List
    Check the glow plug indicator light
    Diagnostic Point
    Try to measure the resistance of the glow plug
    Battery 
    Main fault
    Battery is depleted
    Symptoms
    Difficult to start (cannot crank, crank speed is low), horn is quiet.
    Data List
    Battery Voltage
    When cranking, battery voltage is below 5 V
    Engine - 1 
    Main fault
    Damaged, seized up
    Symptoms
    Cannot crank, crank speed is low, strange noise
    Engine - 2 
    Main fault
    Loss of compression
    Symptoms
    Rough idle (lack of power always)
    Data List
    Engine Speed of Cyl
    1. When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.
    Injection Feedback Val
    1. If Injection Feedback Val is more than 3 mm3/st, the cylinder may have a fault.
    Start System 
    Main fault
    Starter system malfunction
    Symptoms
    Difficult to start
    Data List
    Starter Signal
    1. Ignition switch (STA) operation
      ON: Starter is operating
      OFF: Starter is not operating

  2. Diesel Injection

    Fuel Supply Pump 
    Main fault
    -
    Symptoms
    Difficult to start, engine stalling, rough idle, lack of power
    Data List
    Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
    1. At a stable condition (e.g. Idling), Fuel Press is within +/-5000 kPa of "Target Common Rail Pressure".
    2. If the fuel pressure is 20000 kPa below the target pressure then a lack of power will be felt.
    3. If the fuel pressure is below 25000 kPa then idling will be rough.

    HINT:
    1. The fuel pressure changes at engine starting, but is approx. 25000 kPa at engine start after the engine is warmed up.
    2. When Target Pump SCV Current is 3000 mA or more, the suction control valve has a tendency to become stuck.

    Diagnostic Trouble Code
    Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored.
    Fuel Filter 
    Main fault
    Blockage
    Symptoms
    Difficult to start, engine stalling, rough idle, lack of power
    Data List
    Fuel Press, Target Common Rail Pressure
    1. At a stable condition (e.g. Idling), the fuel pressure is within +/-5000 kPa of "Target Common Rail Pressure ".
    2. If the fuel pressure is 20000 kPa below the target pressure then a lack of power will be felt.
    3. If the fuel pressure is below 25000 kPa then idling will be rough.

    HINT:
    The fuel pressure changes at engine starting, but is approx. 25000 kPa at engine start after the engine is warmed up.

    Diagnostic Trouble Code
    Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored.
    Fuel Injector 
    Main fault
    Blockage
    Symptoms
    Rough idle, lack of power, black smoke, white smoke, knocking
    Data List
    Injection Feedback Val
    1. When an Injection Feedback Val is more than 3 mm3/st, the cylinder is not normal. This can be read after idling for 1 minute with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).
    Pressure Discharge Valve 
    Main fault
    Does not completely close
    Symptoms
    Difficult to start, engine stall, rough idle, lack of power
    Injector Driver (EDU) 
    Main fault
    Circuit fault: The fuel injector does not open.
    Symptoms
    Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
    Data List
    Same as fuel injector
    Diagnostic Trouble Code
    When the EDU has a fault, some DTCs may be stored.
    Fuel Pressure Sensor 
    Main fault
    Open circuit, decrease in performance (foreign matter is stuck)
    Symptoms
    Difficult to start, rough idle, engine stall, lack of power
    Data List
    Fuel Press, Target Common Rail Pressure
    1. Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped, and check that Fuel Press follows Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure. (However, the value may not deviate even when a malfunction is present).
    Diagnostic Trouble Code
    When the fuel pressure sensor has a fault, some DTCs may be stored.
    Irregular Fuel 
    Main fault
    -
    Symptoms
    Difficult to start, rough idle (especially when cold)

  3. Diesel EGR

    EGR System 
    Main fault
    1. Does not move smoothly
    2. Does not close completely
    Symptoms
    1. Rough idle
    2. EGR valve stuck closed: A loud turbocharger sound.
    3. EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt).
    Data List
    Actual EGR Valve Pos., Target EGR Pos.
    1. Generally, Actual EGR Valve Pos. = Target EGR Pos. +/-5% (fully closed 0%, fully open 100%).
    2. Using EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Pos. (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).
    3. EGR valve is fully closed when the ignition switch is turned to ON (engine stopped).
    4. EGR valve opens to the halfway point at idling after the engine warmed up.
    EGR Close Lrn. Val., EGR Close Lrn. Status
    1. When leaving the vehicle idling, when EGR Close Lrn. Status is OK, the normal range of EGR Close Lrn. Val. is 3.75 to 4.8 V.
    2. In cases when EGR Close Lrn. Status. is NG or EGR Close Lrn. Val. is out of the normal range (3.75 to 4.8 V), it is possible that the EGR valve cannot completely close.

  4. Diesel Throttle

    Diesel Throttle System 
    Main fault
    Stuck, does not move smoothly
    Symptoms
    1. Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.
    2. Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.
    Data List
    1. Actual Throttle Position
      0%: Fully open
      100%: Fully closed
    2. When the ignition switch is ON (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is temporarily closed fully.


Data List Related to Starting Trouble
  1. MAP
  2. MAF
  3. Intake Air
  4. Coolant Temp
  5. Battery Voltage
  6. Starter Signal
  7. Engine Speed of Cyl #1 (to #4)
  8. Target Common Rail Pressure
  9. Fuel Press
  10. Target Pump SCV Current
  11. Injection Feedback Val #1 (to #4)
  12. Injection Volume
  13. Actual Throttle Position
  14. Target EGR Position
  15. Actual EGR Valve Pos.
  16. EGR Close Lrn. Status
  17. EGR Close Lrn. Val.

INSPECTION PROCEDURE


Explanation of Symptom
Starting Trouble
For good starting it is essential to have:
  1. Sufficient cranking speed.
  2. Properly operating engine preheating system.
  3. Good quality fuel.
The fuel is ignited by the heat which is generated with compression pressure.
With problems such as a depleted battery, the crankshaft speed can become low, or if the engine compression is leaking, the compression pressure will not rise and there will be difficulty starting.
When the engine is cold, even if there is compression heat, it will escape from the combustion chamber. For this reason, when the engine is started when it is cold, the glow plugs heat the compressed air.
Also, after starting the engine, by charging the glow plugs for a fixed time set according to the engine coolant temperature, diesel knocking and white smoke are prevented. The quantity of fuel injected is determined by the fuel pressure and also the amount of time the fuel injector is open.

Trouble Area Chart According to Problem Cause
A210593E01
A183464E01

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump, the ECM needs initialization (Click here).
  3. After replacing a fuel injector, the ECM needs registration (Click here).

HINT:
  1. Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


1. CHECK ENGINE CRANKING CONDITION
  1. Check the engine cranking condition.

    Result 
    Result
    Proceed to
    Does not crank at all.
    A
    Low cranking speed.

    HINT:
    When cranking speed is low, especially when the temperature is low, check if the engine oil grade matches the recommendation.

    B
    Cranking is OK.
    C



B
CHECK BATTERY CONDITION (Click here)

C
Go to step 6
A


2. CHECK BATTERY CONDITION
  1. Check the battery condition (Click here).



NG
REPLACE BATTERY
OK


3. CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Check if the normal starting screen appears (check whether communication with the ECM is possible).

    HINT:
    Use a tester that is able to communicate with other vehicles.

    OK:
    Communication is possible (vehicle can be recognized).



NG
Go to step 47
OK


4. READ VALUE USING INTELLIGENT TESTER (CLUTCH SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Clutch Switch.

  1. Read the value displayed on the tester.

    Standard:
    Tester Display
    Condition
    Specified Condition
    Clutch Switch
    Clutch pedal depressed
    ON

    Result 
    Result
    Proceed to
    OK
    A
    NG
    B



B
REPLACE CLUTCH SWITCH ASSEMBLY
A


5. READ ALL OUTPUT DTCS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Utility / All Codes.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTCs related to engine are output
    B



B
GO TO RELATED DTC (Click here)
A

END

6. CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)
  1. Check if the fuel level is low.

    Result 
    Result
    Proceed to
    The indicator (fuel warning light) is not illuminated
    A
    The indicator (fuel warning light) is illuminated
    B



B
Go to step 44
A


7. CHECK INITIALIZATION (FUEL SUPPLY PUMP)
  1. When the engine does not start or another problem such as rough idling is present, perform initialization and check to see if the problem symptoms disappear. If the problem symptoms do not disappear, perform the next procedure.

    HINT:
    When replacing the ECM, the supply pump initialization must be performed (Click here).


NEXT


8. READ OUTPUT DTC (RELATED TO ENGINE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTCs related to engine are output
    B



B
REPAIR OR REPLACE ENGINE CONTROL SYSTEM ACCORDING TO DTC OUTPUT (Click here)
A


9. TAKE SNAPSHOT DURING STARTING AND IDLING
A176220E02
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

  1. Take a snapshot of the following Data List items with the intelligent tester during "ignition switch ON (5 seconds) → Starting → Idling (10 seconds)".

    HINT:
    1. A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the illustration below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.
    2. When there is trouble starting with a cold engine, take the snapshot when the engine is cold. Then warm up the engine (engine coolant temperature 70°C (158°F) or more) and after idling the vehicle for 1 minute (A/C off, electrical load off), take a snapshot of the data for 15 seconds while idling.
    3. Graphs like the ones shown below can be displayed by transferring the stored snapshot from the tester to a PC. Intelligent Viewer must be installed on the PC.


NEXT


10. CHECK SNAPSHOT (TARGET PUMP SCV CURRENT)
  1. Check Target Pump SCV Current in the snapshot taken when the engine was starting.

    Result 
    Result
    Proceed to
    Target Pump SCV Current is 3000 mA or more
    A
    Target Pump SCV Current is less than 3000 mA
    B



A
Go to step 13
B


11. CHECK SNAPSHOT (FUEL PRESS)
  1. Check Fuel Press in the snapshot taken when the engine was starting.

    Result 
    Result
    Proceed to
    2 seconds after Starter Signal turns from OFF to ON, Fuel Press is less than 20000 kPa

    HINT:
    As long as the fuel pressure remains below 5000 kPa, the ECM stops sending the injection open signal (IJT) to the EDU, and then the actual injection duration remains 0 microseconds.

    A
    2 seconds after Starter Signal turns from OFF to ON, Fuel Press is 50000 kPa or more
    B
    Except above
    C

    HINT:
    1. Fuel pressure is about 25000 to 35000 kPa when the engine is cranking and the engine coolant temperature is 0°C (32°F) or more.
    2. Fuel pressure increases rapidly during cranking.



B
Go to step 36

C
Go to step 24
A


12. READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)

  1. A148776
    Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.*1

    NOTICE:
    1. Hand pump pumping speed: Maximum of 2 strokes/second.
    2. Be sure to push the hand pump with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Start the engine.

    NOTICE:
    1. Just after starting the engine, visually check for fuel leaks from the supply pump, fuel injector, common rail, and the fuel pipes in high-pressure areas.
    2. Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
    3. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    4. Use a fully-charged battery.

    1. When the engine can be started, proceed to step *2.

    2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to step *1). Then start the engine.

  1. Turn the ignition switch off.*2

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear DTCs (Click here).

  1. Start the engine.*3

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*4

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*5

  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.*6A192848E01

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read Current DTCs.

    1. When no DTCs are output, the air bleeding is completed. Proceed to step *8.

    2. If any DTCs are output, proceed to step *7.

  1. Clear DTCs (Click here).*7

  1. Repeat steps *3 to *6.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.*8

  1. Start the engine.

  1. Read the Fuel Press values while cranking and idling the engine.

    Result 
    Result
    Proceed to
    The engine cannot be started or the engine can be started but Fuel Press is less than 20000 kPa 2 seconds after the starter signal changes from OFF to ON.
    B
    Except above
    A



B
Go to step 14
A

END

13. CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)

  1. A099839E14
    Disconnect the S8 suction control valve connector.

  1. Disconnect the E8 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    S8-1 - E8-2 (PCV+)
    Always
    Below 1 Ω
    S8-2 - E8-1 (PCV-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    S8-1 or E8-2 (PCV+) - Body ground
    Always
    10 kΩ or higher
    S8-2 or E8-1 (PCV-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the suction control valve connector.

  1. Reconnect the ECM connector.



OK
Go to step 15

NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
14. INSPECT COMMON RAIL ASSEMBLY
  1. Inspect the common rail assembly (Click here).



NG
Go to step 21
OK


15. CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP
  1. Disconnect the inlet hose from the fuel supply pump.

  1. Operate the priming pump and check that fuel is being supplied to the fuel supply pump.

    OK:
    Fuel is properly supplied to the fuel supply pump when the priming pump is operated.

    HINT:
    1. When there is a lack of fuel, fuel pressure drops.
    2. Inspect for fuel filter clogging (check that the fuel filter is not clogged).



NG
Go to step 43
OK


16. REPLACE FUEL SUPPLY PUMP
  1. Replace the fuel supply pump (Click here).


NEXT


17. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).


NEXT


18. PERFORM FUEL SUPPLY PUMP INITIALIZATION
  1. Perform fuel supply pump initialization (Click here).


NEXT


19. READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

  1. Start the engine.

  1. Read the Fuel Press values while cranking and idling the engine.

    Result 
    Result
    Proceed to
    The engine cannot be started or the engine can be started but Fuel Press is less than 20000 kPa 2 seconds after the starter signal changes from OFF to ON.
    B
    Except above
    A



B
Go to step 20
A

END

20. INSPECT FUEL INJECTOR (INSPECTION FOR VALVE CLOSING PROBLEM)
  1. Remove the glow plug assembly for all the cylinders (Click here).

  1. Visually check if there is fuel on the glow plugs.

    HINT:
    1. If there is fuel on a glow plug, fuel may be leaking from a fuel injector.
    2. After replacing a fuel injector, make sure that the common rail pressure (fuel pressure) is within +/-5000 kPa of the target fuel pressure while cranking the engine.
    3. If there is fuel on a glow plug, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.

    Result 
    Result
    Proceed to
    No fuel on glow plugs
    A
    Fuel on glow plugs
    B

  1. Install the glow plug assembly (Click here).



B
Go to step 29
A


21. REPLACE COMMON RAIL
  1. Replace the common rail (Click here).


NEXT


22. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).


NEXT


23. READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

  1. Start the engine.

  1. Read the Fuel Press values while cranking and idling the engine.

    Result 
    Result
    Proceed to
    The engine cannot be started or the engine can be started but Fuel Press is less than 20000 kPa 2 seconds after the starter signal changes from OFF to ON.
    B
    Except above
    A



B
Go to step 25
A

END

24. INSPECT INJECTOR COMPENSATION CODE
  1. Read the injector compensation code (Click here).

    OK:
    Compensation codes stored in the ECM match compensation codes of the installed fuel injectors.



NG
REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING (Click here)
OK


25. CHECK DATA LIST

  1. A176220E02
    Check Injection Feedback Val # and Injection Volume in the snapshot taken when the engine was idling.
    Result 
    Result
    Proceed to
    Injection Feedback Val #1 to #4 are more than 3 mm3/st

    HINT:
    There may be a malfunction in the corresponding cylinder.

    A
    Injection Feedback Val #1 to #4 are 3 mm3/st or less
    Injection Volume is more than 10 mm3/st
    B*
    Injection Feedback Val #1 to #4 are 3 mm3/st or less
    Injection Volume is 10 mm3/st or less
    C

    HINT:
    1. *: When case "B" occurs, usually symptoms may be noticeable, such as difficult starting, rough idling, knocking or black smoke at high common rail pressure.
    2. The shift lever should be in neutral and the A/C switch and all accessory switches should be off.



B
Go to step 39

C
Go to step 30
A


26. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

HINT:
Use this Active Test to determine the malfunctioning cylinder.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

HINT:
  1. If the engine idle speed does not change when a fuel injector is disabled, the cylinder being tested is malfunctioning.
  2. If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.


NEXT


27. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION)

HINT:
Use this Active Test to help determine whether a cylinder has compression loss or not.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.

  1. Check the engine speed during the Active Test.

    OK:
    The values of Engine Speed Cyl #1 to #4 are within +/-10 rpm of each other.

    HINT:
    When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a loss of compression in that cylinder.



OK
Go to step 29

NG
Go to step 28
28. CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER

HINT:
Measure the compression of the cylinder that had a high speed during the Active Test "Check the Cylinder Compression".

  1. Check the cylinder compression pressure (Click here).



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


29. REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER

HINT:
The injector is determined to be faulty as the corresponding cylinder is malfunctioning, but has no compression loss.

  1. Replace the fuel injector (Click here).



NEXT
Go to step 40
30. CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS
  1. Check the temperature when starting trouble occurs.

Result 
Result
Proceed to
Difficult to start only for cold engine.
A
Difficult to start both for cold and warmed up engine.
B


B
Go to step 33
A


31. INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


32. INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)
E110714
  1. Disconnect the glow plug wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Glow plug terminal - Body ground
    20°C (68°F)
    Approximately 0.95 Ω

    HINT:
    If any of the glow plugs has an open circuit, the engine power will be insufficient only when the engine is cold.

    NOTICE:
    1. Exercise extreme care not to damage the glow plug pipes. Damaging them could cause an open circuit or shorten the life of the glow plugs.
    2. Keep the glow plugs free of oil and fuel while cleaning.
    3. Wipe any oil off of the terminal and Bakelite washer with a clean, dry cloth during inspection.
    4. Do not apply higher than 11 V to the glow plugs as it may cause an open circuit.



NG
REPLACE GLOW PLUG ASSEMBLY (Click here)
OK


33. CHECK FUEL QUALITY
  1. Check that fuel with a low cetane number is used.


NEXT


34. CHECK ENGINE STARTING CONDITION
  1. Check whether the engine can be started.

    HINT:
    If there are deposits in the injectors and they are left for a long time, the injectors for all the cylinders may become stuck.

    Result 
    Result
    Proceed to
    The engine can be started.
    A
    There is no initial combustion even when the engine can be cranked.
    B



B
Go to step 39
A


35. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check whether the difficulty starting has been successfully repaired by starting the engine.


NEXT

END

36. CHECK SNAPSHOT

HINT:
When all Data List values are OK and Fuel Press is higher than Target Common Rail Pressure, perform the following inspection.


NEXT


37. INSPECT INJECTOR DRIVER (EDU POWER SOURCE)

  1. A221614E01
    Disconnect the I17 injector driver (EDU) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I17-2 (+B) - I17-3 (GND)
    Ignition switch ON
    11 to 14 V

  1. Reconnect the injector driver (EDU) connector.



NG
GO TO INJECTOR CIRCUIT (Click here)
OK


38. INSPECT FUEL INJECTOR

HINT:
If there is no initial combustion during cranking, there may be air in the injectors.


NEXT

END

39. REPLACE FUEL INJECTORS OF ALL CYLINDERS
  1. Replace the fuel injectors (Click here).


NEXT


40. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).


NEXT


41. REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
  1. Register the injector compensation codes (Click here).

  1. Perform the fuel injector pilot quantity learning (Click here).


NEXT


42. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

  1. Start the engine.

  1. Read the Fuel Press values while cranking and idling the engine.

    OK:
    The engine can be started and Fuel Press is 20000 kPa or higher 2 seconds after the starter signal changes from OFF to ON.


NEXT

END

43. CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)
  1. Check and repair or replace the clogged fuel pipe.



NEXT
Go to step 45
44. ADD FUEL
  1. Add fuel.


NEXT


45. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).


NEXT


46. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

  1. Start the engine.

  1. Read the Fuel Press values while cranking and idling the engine.

    OK:
    The engine can be started and Fuel Press is 20000 kPa or higher 2 seconds after the starter signal changes from OFF to ON.


NEXT

END

47. CHECK VC OUTPUT CIRCUIT
  1. Check the VC output circuit (Click here).


NEXT


48. CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Check if the normal starting screen appears (check whether communication with the ECM is possible).

    HINT:
    Use a tester that is able to communicate with other vehicles.

    OK:
    Communication is possible (vehicle can be recognized).



NG
Go to step 49
OK

END

49. CHECK ECM POWER SOURCE CIRCUIT
  1. Check the ECM power source circuit (Click here).


NEXT


50. CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Check if the normal starting screen appears (check whether communication with the ECM is possible).

    HINT:
    Use a tester that is able to communicate with other vehicles.

    OK:
    Communication is possible (vehicle can be recognized).



NG
REPLACE ECM (Click here)
OK

END


← Engine Difficult to Start or Stalling (Jun 2011 – Jul 2012)Engine Difficult to Start or Stalling (Aug 2013 – Jul 2014) →