When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag activation.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
2.
REMOVE HOOD SUB-ASSEMBLY
Disconnect the washer nozzle hose.
Remove the 4 bolts and hood.
3.
REMOVE NO. 1 ENGINE UNDER COVER (for 4WD)
Remove the 4 bolts and No. 1 engine under cover.
4.
REMOVE NO. 2 ENGINE UNDER COVER (for 4WD)
Remove the 2 bolts and No. 2 engine under cover.
5.
DRAIN ENGINE OIL
Remove the oil filler cap.
Remove the oil drain plug, and drain the engine oil from the oil pan.
NOTICE:
Collect the oil in an oil disposal container.
6.
LOOSEN FUEL TANK CAP ASSEMBLY
7.
DRAIN ENGINE COOLANT
NOTICE:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.
Loosen the cylinder block drain cock plug and the radiator drain cock plug.
HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.
8.
REMOVE BATTERY BRACKET
9.
REMOVE BATTERY AND BATTERY TRAY
10.
REMOVE AIR CLEANER ASSEMBLY
for Ventilation Hose Type: Disconnect the ventilation hose.
w/ Mass Air Flow Meter: Disconnect the mass air flow meter sensor connector.
w/ Intake Air Temperature Sensor: Disconnect the intake air temperature sensor connector.
Slightly bend the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.
Text in Illustration
*1
Stopper
Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.
Text in Illustration
*1
Hinge
20.
DISCONNECT WIRE HARNESS
Remove the upper relay block cover.
Remove the side relay block cover.
Remove the nut and disconnect the engine room junction block wire.
Disconnect the 2 engine room junction block connectors.
Remove the bolt and disconnect the ground cable.
Remove the 2 nuts, detach the clamp and disconnect the wire harness.
Disconnect the 3 EDU connectors.
w/ A.D.D. Disconnect the 4WD control ECU connector.
Disconnect the 4 ECM connectors.
21.
DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
Remove the 4 bolts and disconnect the cooler compressor.
HINT:
It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.
Place matchmarks on the clutch cover and flywheel.
Loosen each set bolt one turn at a time until spring tension is released.
Remove the 6 set bolts and pull off the clutch cover.
NOTICE:
Do not drop the clutch disc.
24.
REMOVE CLUTCH DISC ASSEMBLY
NOTICE:
Keep the lining part of the clutch disc, pressure plate and surface of the flywheel away from oil and foreign matter.
25.
REMOVE FLYWHEEL SUB-ASSEMBLY
Using SST, hold the crankshaft pulley.
SST
09213-58014 09330-00021
Remove the 8 bolts and flywheel.
26.
REMOVE REAR END PLATE
Remove the bolt and rear end plate.
27.
REMOVE ENGINE ASSEMBLY
Install a No. 1 engine hanger and No. 2 engine hanger with 2 bolts as shown in the illustration.
HINT:
Part No.
No. 1 Engine hanger
w/ EGR cooler
12284-30060
Bolt (91552-81014)
w/o EGR cooler
12284-30020
Bolt (91552-81014)
No. 2 Engine hanger
12282-67030
Bolt (91642-81030)
Torque:
for No. 1 engine hanger:
25 N*m{
255 kgf*cm
, 18 ft.*lbf
}
for No. 2 engine hanger:
60 N*m{
612 kgf*cm
, 44 ft.*lbf
}
NOTICE:
Install the engine hangers with new bolts.
Attach an engine sling device and hang the engine with a chain block.
Remove the bolt and No. 2 cylinder block insulator.
Remove the 4 bolts and 4 nuts.
Remove the engine by operating the engine sling device and chain block.
28.
FIX ENGINE ON ENGINE STAND
29.
REMOVE ENGINE WIRE
Remove the engine wire.
30.
REMOVE NO. 1 TIMING BELT COVER
Remove the bolt and water hose clamp.
Remove the wire harness clamp.
Remove the 6 bolts and timing belt cover.
31.
REMOVE TIMING BELT
Turn the crankshaft clockwise and align the timing marks as shown in the illustration.
Uniformly loosen the 2 bolts and remove the timing belt tensioner.
Remove the timing belt.
Using a 10 mm hexagon wrench, remove the bolt, timing belt idler and washer.
HINT:
When turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise.
When installing the timing belt, return the camshaft to the timing marks and then turn the crankshaft clockwise until it aligns with the timing marks, as shown in the illustration.