Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009577 1GR-FE ENGINE MECHANICAL _0052210 ENGINE ASSEMBLY A

1GR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 6.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer nozzle hose.


b.

Remove the 4 bolts and hood.


Hide 7.REMOVE ENGINE SIDE COVER SUB-ASSEMBLY LH

Hide 8.REMOVE ENGINE SIDE COVER SUB-ASSEMBLY RH

Hide 9.REMOVE NO. 1 ENGINE UNDER COVER

Hide 14.REMOVE NO. 2 AIR CLEANER HOSE

a.

Remove the 2 bolts and No. 2 air cleaner hose.


Hide 16.REMOVE RADIATOR SIDE DEFLECTOR RH

Hide 17.REMOVE RADIATOR SIDE DEFLECTOR LH

Hide 18.REMOVE RADIATOR HOSE INLET

Hide 19.REMOVE RADIATOR HOSE OUTLET

Hide 20.DISCONNECT OIL COOLER INLET HOSE

Hide 21.DISCONNECT OIL COOLER OUTLET HOSE

Hide 24.DISCONNECT VANE PUMP ASSEMBLY

A076444

a.

Disconnect the power steering oil pressure switch connector.


b.

Remove the 2 bolts and disconnect the vane pump.

NOTICE:

Do not hit other parts with the pulley when disconnecting the vane pump.


HINT:

Make sure to suspend the vane pump securely.



Hide 26.DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 27.DISCONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY

Hide 28.DISCONNECT HEATER WATER HOSE

a.
A302076

Disconnect the heater water inlet hose.


b.

Disconnect the heater water outlet hose.


Hide 30.DISCONNECT ENGINE WIRE

A191307

a.

Disconnect the ECM connectors from the cabin

i.

Remove the glove compartment door (See page Vehicle Interior>INTERIOR PANELS / TRIM>UPPER INSTRUMENT PANEL>REMOVAL).


ii.

Disconnect the 4 ECM connectors.


iii.

Disconnect the 4 wheel drive control ECU connector.



b.
A252952
0.771,2.219 0.99,2.406 0.219,0.188 10 false *a
*a Frame Side


Remove the bolt and clamp, and disconnect the ground wire.


c.

Remove the bolt and disconnect the ground wire from the frame.


d.

Pull out the engine wire from the cabin.


e.

Remove the upper relay block cover.


f.
A302077
0.385,0.823 0.698,1.021 0.313,0.198 10 false *a 2.854,1.167 3.167,1.365 0.313,0.198 10 false *a 2.563,1.885 2.875,2.083 0.313,0.198 10 false *a
*a Pull


Remove the side relay block cover.

i.

Using a screwdriver, detach the 4 claws and remove the relay block cover.

HINT:

Tape the screwdriver tip before use.




g.

Remove the nut and disconnect the cable from the engine room junction block.


h.

Disconnect the 2 engine room junction block connectors and detach the wire clamp.


i.

Remove the bolt and detach the wire clamp from the front No. 1 engine mounting bracket LH.


j.

Disconnect the differential actuator connector.


Hide 31.DISCONNECT NO. 2 ENGINE WIRE

a.
A251969

Remove the bolt and disconnect the No. 2 engine wire from the cylinder block.


Hide 32.REMOVE BATTERY

Hide 33.REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY

Hide 35.REMOVE FRONT FENDER SEAL

a.

Remove the 10 clips and RH and LH fender seals.


Hide 36.REMOVE FRONT FENDER APRON SEAL UPPER

a.

Remove the 10 clips and RH and LH fender apron seals.


Hide 43.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

G034260

a.

Remove the 4 bolts and rear No. 1 engine mounting insulator from the automatic transmission.


Hide 45.INSTALL ENGINE HANGER

a.
A072941
1.656,1.688 1.656,1.521 1.656,1.521 1,1.083 true 2.677,0.125 2.813,0.125 2.813,0.125 3,0.76 false 1.573,1.729 1.771,1.906 0.198,0.177 10 true *1 2.458,0.042 2.656,0.208 0.198,0.167 10 false *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the 2 engine hangers with 4 bolts as shown in the illustration.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-31060
No. 2 Engine Hanger 12282-31040
Bolt 90119-08A87



Hide 46.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine with a chain block.


b.
A250918

Remove the 4 bolts and 4 nuts holding the engine mounting brackets to the frame.


c.

Lift the engine out of the vehicle carefully.

NOTICE:
·

Make sure the engine is clear of all wiring and hoses.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.

·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.




Hide 47.INSTALL ENGINE TO ENGINE STAND

a.

Install the engine to an engine stand with bolts.


b.

Remove the 2 engine hangers and 4 bolts.