Home › Engine / Hybrid System › 2TR-FBE ENGINE MECHANICAL › ENGINE UNIT › from 2014.10
RM1840EF _51 Engine / Hybrid System _009576 2TR-FBE ENGINE MECHANICAL _0052200 ENGINE UNIT A

2TR-FBE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL CRANKSHAFT PULLEY SET KEY

a.

Install the 2 pulley set keys to the crankshaft.


Hide 2.INSTALL NO. 4 CHAIN VIBRATION DAMPER

a.

Install the vibration damper with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 3.INSTALL NO. 2 CHAIN SUB-ASSEMBLY

a.
A101978

Install the No. 2 crankshaft timing sprocket as shown in the illustration.

NOTICE:

Check that the No. 1 cylinder is at TDC and that the weights of the No. 1 and No. 2 balance shafts are at the bottom.


HINT:

Install the timing sprocket with the front mark facing forward.



b.
A101339C01
2.75,0.344 1.531,0.104 1.531,0.104 1.448,0.104 true 2.75,0.635 3.083,1.51 3.083,1.51 3.167,1.51 true 3.083,1.51 2.698,2.625 true 2.927,2.781 2.083,3.125 2.083,3.125 1.948,3.125 true 2.135,3.094 2.51,2.844 true 1.24,0 1.469,0.198 0.229,0.198 10 false *1 1.76,3.031 1.927,3.229 0.167,0.198 10 false *1 3.198,1.427 3.417,1.635 0.219,0.208 10 false *2
*1 Mark Plate (Yellow)
*2 Timing Mark


As shown in the illustration, install the chain to the sprocket and gear with the mark plates aligned with the timing marks on the sprocket and gear.


c.
A101340C01
0.365,0.813 0.469,1.406 0.469,1.406 0.563,1.406 true 0.635,0.688 1.073,0.125 1.073,0.125 1.156,0.125 true 0.625,1.292 0.823,1.49 0.198,0.198 10 false *1 1.208,0.021 1.427,0.219 0.219,0.198 10 false *2
*1 Mark Plate (Yellow)
*2 Large Timing Mark


Fit the other mark plate of the chain behind the large timing mark of the balance shaft drive gear.


d.

Insert the balance shaft drive gear shaft through the balance shaft drive gear so that it fits into the thrust plate hole.


e.
A302844C01
0.958,0.938 1.74,0.635 true 0.917,1.104 1.75,0.625 1.75,0.625 1.927,0.625 false 0.698,0.646 1.531,0.167 1.531,0.167 1.708,0.167 true 0.448,0.813 0.552,2.083 0.552,2.083 0.719,2.083 true 1.802,0.073 2.115,0.229 0.313,0.156 10 false *1 2,0.531 2.313,0.688 0.313,0.156 10 false *2 0.781,1.969 1.094,2.125 0.313,0.156 10 false *3
*1 Large Timing Mark
*2 Small Timing Mark
*3 Mark Plate (Yellow)


Align the small timing mark of the balance shaft drive gear with the large timing mark of the balance shaft timing gear.


f.

Install the bolt to the balance shaft drive gear.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


g.
A101342C01
2.844,0.292 2.302,0.094 2.302,0.094 2.146,0.094 true 0.604,0.542 1.365,0.073 1.365,0.073 1.458,0.073 true 0.802,0.781 1.448,0.51 1.448,0.51 1.51,0.51 true 1.417,0.531 0.781,0.938 true 2.833,0.552 2.833,1.344 true 2.781,2.677 2.906,1.823 2.906,1.823 3.031,1.823 true 0.354,0.615 0.125,1.24 0.125,1.24 0.125,1.333 true 2.99,2.875 2.49,3.302 2.49,3.302 2.427,3.302 true 2.49,3.302 2.625,2.927 true 1.938,0.021 2.125,0.198 0.188,0.177 10 false *3 0.063,1.396 0.24,1.604 0.177,0.208 10 false *3 2.167,3.188 2.333,3.354 0.167,0.167 10 false *3 1.521,0.021 1.698,0.219 0.177,0.198 10 false *1 1.563,0.417 1.729,0.573 0.167,0.156 10 false *2 2.75,1.385 2.938,1.573 0.188,0.188 10 false *4 3.083,1.74 3.323,1.927 0.24,0.188 10 false *4
*1 Large Timing Mark
*2 Small Timing Mark
*3 Mark Plate (Yellow)
*4 Timing Mark


Check that each timing mark is aligned with the corresponding mark plate.

NOTICE:

Check that the No. 1 cylinder is at TDC and that the weights of the No. 1 and No. 2 balance shafts are at the bottom.



Hide 4.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

a.

Install the chain tensioner assembly with the nut.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Install the chain tensioner with the pin installed, and then remove the pin after installation. When performing this step, do not push the vibration damper against the chain.



b.
A101320C02
1.01,1.188 0.844,1.938 0.844,1.938 1.021,1.938 true 0.604,1.208 0.781,0.281 0.781,0.281 0.635,0.281 true 0.427,0.188 0.604,0.385 0.177,0.198 10 false *1 1.073,1.854 1.271,2.052 0.198,0.198 10 false *2
*1 Plunger
*2 Stopper Plate


Move the stopper plate downward to release the lock and push the plunger deep into the tensioner.


c.

Move the stopper plate upward to set the lock and insert a hexagon wrench into the stopper plate hole.


Hide 5.INSTALL NO. 3 CHAIN VIBRATION DAMPER

a.

Install the chain vibration damper with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 6.INSTALL NO. 2 CHAIN VIBRATION DAMPER

a.

Install the chain vibration damper with the bolt.

Torque:
27 N*m (270 kgf*cm, 20 ft.*lbf)


b.

Remove the pin from the chain tensioner assembly to release the plunger.


Hide 7.INSTALL NO. 1 TAPER SCREW PLUG

a.

Install the screw plug to the cylinder block.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 8.INSTALL OIL FILTER BRACKET SUB-ASSEMBLY

a.

Using a hexagon wrench, install the oil filter bracket union.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


b.
G037305C02
1.125,1.302 1.74,0.917 1.74,0.917 2.052,0.917 true 2.479,2.76 2.292,2.958 2.292,2.958 2.01,2.958 true 1.823,2.844 2,3.01 0.177,0.167 10 false *2 2.115,0.792 2.292,0.958 0.177,0.167 10 false *1
*1 New O-Ring
*2 New Oil Filter Bracket Gasket


Install a new oil filter bracket gasket to the oil filter bracket.


c.

Install a new O-ring to the oil filter bracket union.

NOTICE:

Apply a light coat of engine oil to the O-ring and oil filter bracket.



d.

Install 2 new gaskets and the 2 screw plugs to the oil filter bracket.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


e.

Install the oil filter bracket with the 2 bolts and nut.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


f.

Using a 27 mm socket wrench, install the oil filter union.

Torque:
43 N*m (439 kgf*cm, 32 ft.*lbf)


Hide 9.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Check and clean the oil filter installation surface.


b.

Apply clean engine oil to the gasket of a new oil filter.


c.

Lightly screw the oil filter into place, and tighten it until the gasket contacts the seat.


d.
A097902N02
1.198,1.479 0.813,1.677 true 0.458,1.646 0.844,1.833 0.385,0.188 10 false SST

Using SST, tighten the oil filter.

SST
09228-07501  

Torque:
17 N*m (175 kgf*cm, 13 ft.*lbf)


Hide 10.INSTALL REAR CRANKSHAFT OIL SEAL

a.
A302845C01
2.281,0.677 2.833,1.073 2.833,1.073 2.583,1.219 true 1.896,1.885 2.188,2 false 2.167,2 2.51,1.896 false 2.969,1.01 3.427,1.208 0.458,0.198 10 false SST 2.083,2 2.385,2.167 0.302,0.167 10 false *1
*1 Wooden Block


Place the oil seal retainer on wooden blocks.


b.

Apply a light coat of MP grease to the lip of a new oil seal.

NOTICE:
·

Do not allow foreign matter to contact the lip of the oil seal.

·

Do not allow MP grease to contact the dust seal.




c.

Using SST, tap in a new oil seal until its surface is flush with the oil seal retainer edge.

SST
09223-15030  
09950-70010  (09951-07150)

NOTICE:
·

Wipe off any extra grease from the crankshaft.

·

Do not tap in the oil seal at an angle.




Hide 11.INSTALL REAR ENGINE OIL SEAL RETAINER

a.
A097914C02
1.01,1.854 1.292,2.052 0.281,0.198 10 false *1
*1 Seal Packing


Apply seal packing in a continuous bead as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the rear oil seal retainer within 3 minutes after applying seal packing.

·

Do not start the engine for at least 4 hours after installation.




b.

Install the oil seal retainer with the 6 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 12.INSTALL OIL CONTROL VALVE FILTER

a.

Check that no foreign matter is on the mesh part of the filter.

If foreign matter is present, clean the part thoroughly.


b.

Using an 8 mm hexagon wrench, install a new gasket and the oil control valve filter with the screw plug.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 15.INSTALL CAMSHAFT TIMING SPROCKET

a.

Mount the camshaft in a vise and install the camshaft timing sprocket to the camshaft with the sprocket bolt.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)

NOTICE:

Do not damage the camshaft in the vise.



Hide 19.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 22.INSTALL CRANKSHAFT TIMING SPROCKET

a.
A101308

Install the timing sprocket as shown in the illustration.


Hide 30.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 31.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 33.INSTALL OIL PAN STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


A333967E01
2.646,1.75 2.865,2.271 2.865,2.271 3.031,2.271 true 2.313,2.052 2.396,2.354 2.396,2.354 2.563,2.354 true 3.281,0.781 3.49,0.365 3.49,0.365 3.656,0.365 true 4.698,3.313 5.094,2.729 5.094,2.729 5.281,2.729 true 4.708,3.708 5.063,4.167 5.063,4.167 5.271,4.167 true 1.646,3.771 2,4.229 2,4.229 2.313,4.229 true 1.646,3.271 2.042,2.688 2.042,2.688 2.375,2.688 true 1.219,2.469 1.375,2.667 0.156,0.198 10 false A 4.271,2.708 4.427,2.906 0.156,0.198 10 false B 3.083,2.177 3.24,2.375 0.156,0.198 10 false A 2.604,2.26 2.76,2.458 0.156,0.198 10 false B 3.708,0.26 3.865,0.458 0.156,0.198 10 false B 5.333,2.635 6.521,2.833 1.188,0.198 10 false 8.5 mm (0.335 in.) 5.438,3.396 6.625,3.594 1.188,0.198 10 false 18 mm (0.709 in.) 5.323,4.063 6.51,4.26 1.188,0.198 10 false 8 mm (0.315 in.) 2.385,3.396 3.573,3.594 1.188,0.198 10 false 27 mm (1.06 in.) 2.375,4.125 3.563,4.323 1.188,0.198 10 false 9 mm (0.354 in.) 2.417,2.583 3.604,2.781 1.188,0.198 10 false 16 mm (0.630 in.)

a.

Using E5 and E6 "TORX" socket wrenches, install the stud bolts.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 38.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 45.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.

Install the gasket to the oil filler cap.


b.

Install the oil filler cap.