Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.11–2016.07
RM33K0E _58 Vehicle Interior _043550 METER / GAUGE / DISPLAY _0227399 METER / GAUGE SYSTEM T

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  PROBLEM SYMPTOMS TABLE  


NOTICE:
·

When replacing the combination meter assembly, make sure to replace it with a new one.

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.

·

w/ Smart Entry and Start System:

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system.



HINT:
·

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptom are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.



Meter Gauge
Symptom Suspected Area Link
Speedometer malfunction Refer to "Speedometer Malfunction" Click here
Tachometer malfunction Refer to "Tachometer Malfunction" Click here
Fuel receiver gauge malfunction
(Fuel receiver gauge is currently malfunctioning, or was malfunctioning in the past)
Refer to "Fuel Receiver Gauge Display Malfunction" Click here
Engine coolant temperature receiver gauge malfunction Refer to "Engine Coolant Temperature Receiver Gauge Malfunction" Click here

Warning Light or Indicator Light
Symptom Suspected Area Link
Turn indicator light malfunction (Turn signal light operates normally) Perform Active Test [Turn Signal (Left) Indicator, Turn Signal (Right) Indicator] Click here
Proceed to "Turn Signal Switch Circuit" Click here
Proceed to "Hazard Warning Switch Circuit" Click here
Combination meter assembly Click here
Front fog indicator light malfunction (Front fog light operates normally) (w/ Front Fog Light) Perform Active Test [Indicat. Lamp Fr FOG] Click here
Harness or connector -
Combination meter assembly Click here
Rear fog indicator light malfunction (Rear fog light operates normally) (w/ Rear Fog Light) Harness or connector -
Combination meter assembly Click here
Taillight indicator light malfunction (Taillight operates normally) Perform Active Test [Indicat. Lamp Tail] Click here
Harness or connector -
Combination meter assembly Click here
High beam indicator light malfunction (High beam headlight operates normally) Perform Active Test [Indicat. Lamp Beam] Click here
Harness or connector -
Combination meter assembly Click here
Smart key indicator light malfunction (w/ Smart Smart Entry and Start System) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Perform Active Test [Smart System Indicator] Click here
Perform Active Test [Smart System Warning] Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
Cruise indicator light malfunction (w/ Cruise Control System) Proceed to "Cruise Main Indicator Light Circuit" Click here
Combination meter assembly Click here
SET indicator light malfunction (w/ Cruise Control System) Proceed to "Cruise SET Indicator Light Circuit" Click here
Combination meter assembly Click here
Brake override system warning light malfunction CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Check indicator/warning light Click here
Perform Active Test [Brake Override Indicator] Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
SFI system (for 2TR-FE) Click here
SFI system (for 1GR-FE) Click here
Combination meter assembly Click here
Seat belt warning light malfunction Proceed to "Driver Side Seat Belt Warning Light does not Operate" Click here
Proceed to "Front Passenger Side Seat Belt Warning Light Malfunction" Click here
Parking brake warning light malfunction Perform Active Test [Indicat. Park] Click here
Parking brake switch assembly Click here
Harness or connector -
Combination meter assembly Click here
Brake warning light malfunction Check indicator/warning light Click here
Perform Active Test [Indicat. Lamp Brake] Click here
Proceed to "Brake Warning Light Remains ON" (w/ VSC) Click here
Proceed to "Brake Warning Light does not Come ON" (w/ VSC) Click here
Proceed to "Brake Warning Light Remains ON" (w/o VSC) Click here
Proceed to "Brake Warning Light does not Come ON" (w/o VSC) Click here
Harness or connector -
Brake master cylinder sub-assembly (brake fluid level warning switch) Click here
Vacuum warning switch assembly (for Diesel Engine) Click here
Combination meter assembly Click here
SRS warning light malfunction Check indicator/warning light Click here
Perform Active Test [Indicat. Lamp Airbag] Click here
Proceed to "SRS Warning Light Remains ON" (Type A) Click here
Proceed to "SRS Warning Light does not Come ON" (Type A) Click here
Proceed to "SRS Warning Light Remains ON" (Type B) Click here
Proceed to "SRS Warning Light does not Come ON" (Type B) Click here
Combination meter assembly Click here
Charger system warning light malfunction (for 1GD-FTV, 2TR-FE, 1GR-FE) Perform Active Test [Indicat. Lamp Charge] Click here
Charging system (for 1GD-FTV) Click here
Charging system (for 2TR-FE) Click here
Charging system (for 1GR-FE) Click here
Combination meter assembly Click here
Charger system warning light malfunction (for 1KD-FTV) Harness or connector -
Generator assembly (for 1KD-FTV) Click here
Combination meter assembly Click here
Low engine oil pressure warning light malfunction Check indicator/warning light Click here
Perform Active Test [Indicat. Oil Pressure] Click here
Engine oil pressure switch assembly (for 1GD-FTV) Click here
Engine oil pressure switch assembly (for 1KD-FTV) Click here
Engine oil pressure switch assembly (for 2TR-FE) Click here
Engine oil pressure switch assembly (for 1GR-FE) Click here
Harness or connector -
Combination meter assembly Click here
A/T OIL TEMP warning light malfunction (for 4WD, Automatic Transmission) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Check indicator/warning light Click here
Perform Active Test [A/T Oil Temperature Operation] Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
SFI system (for 2TR-FE) Click here
SFI system (for 1GR-FE) Click here
Combination meter assembly Click here
Four-wheel drive indicator light (for 4WD) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Perform Active Test [Indicat. 4WD (Yellow)] Click here
Perform Active Test [4WD Indicator (Green)] Click here
Touch select 2-4 and high-low system Click here
Combination meter assembly Click here
Low speed four-wheel drive indicator light (for 4WD) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Perform Active Test [Indicat. 4LO] Click here
Differential system (w/ Differential Lock) Click here
Combination meter assembly Click here
T-BELT indicator light malfunction (for 1KD-FTV) Check indicator/warning light Click here
Combination meter assembly Click here
Rear differential lock indicator light (for 4WD) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Perform Active Test [Indicat. Rr DIFF LOCK] Click here
Differential system (w/ Differential Lock) Click here
Combination meter assembly Click here
MIL (Malfunction indicator lamp) malfunction CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Check indicator/warning light Click here
Perform Active Test [Check Engine Indicator] Click here
Proceed to "MIL Circuit" (for 1GD-FTV) Click here
Proceed to "MIL Circuit" (for 1GD-FTV, w/ DPF) Click here
Proceed to "MIL Circuit" (for 1GD-FTV, for i-ART) Click here
Proceed to "MIL Circuit" (for 1KD-FTV) Click here
Proceed to "MIL Circuit" (for 2TR-FE) Click here
Proceed to "MIL Circuit" (for 1GR-FE) Click here
Combination meter assembly Click here
Slip indicator light malfunction (w/ VSC) Check indicator/warning light Click here
Perform Active Test [Indicat. Lamp Slip] Click here
Proceed to "Slip Indicator Light Remains ON" Click here
Proceed to "Slip Indicator Light does not Come ON" Click here
Combination meter assembly Click here
VSC OFF indicator light malfunction (w/ VSC) Check indicator/warning light Click here
Perform Active Test [Indicat. VSC OFF] Click here
Proceed to "VSC OFF Switch Circuit" Click here
Combination meter assembly Click here
TRC OFF indicator light malfunction (w/ VSC) Check indicator/warning light Click here
Perform Active Test [VSC TRC Indicator] Click here
Vehicle stability control system Click here
Combination meter assembly Click here
ABS warning light malfunction Check indicator/warning light Click here
Perform Active Test [Indicat. Lamp ABS] Click here
Proceed to "ABS Warning Light Remains ON" (w/ VSC) Click here
Proceed to "ABS Warning Light does not Come ON" (w/ VSC) Click here
Proceed to "ABS Warning Light Remains ON" (w/o VSC) Click here
Proceed to "ABS Warning Light does not Come ON" (w/o VSC) Click here
Combination meter assembly Click here
Downhill assist control system indicator light malfunction (w/ Downhill Assist Control) Check indicator/warning light Click here
Perform Active Test [Indicat. Downhill Assist Control] Click here
Proceed to "Downhill Assist Control Indicator Light Remains ON" Click here
Proceed to "Downhill Assist Control Indicator Light does not Come ON" Click here
Combination meter assembly Click here
GLOW indicator light malfunction (for Diesel Engine) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Perform Active Test [Indicat. GLOW] Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
Combination meter assembly Click here
Fuel system warning light malfunction (for Diesel Engine) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Check indicator/warning light Click here
Perform Active Test [Indicat. Fuel Filter Indicator] Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
Fuel filter assembly (level warning switch) (for 1GD-FTV) Click here
Fuel filter assembly (level warning switch) (for 1KD-FTV) Click here
Fuel filter assembly (clogging switch) (for 1KD-FTV) Click here
Fuel filter assembly (clogging switch) (for 1GD-FTV) Click here
Harness or connector -
Combination meter assembly Click here
ECM (for 1GD-FTV) Click here
ECM (for 1KD-FTV) Click here
Low engine oil level warning light malfunction (Tachometer and engine coolant temperature receiver gauge are operate normally) (for 1GD-FTV) Check indicator/warning light Click here
Perform Active Test [Indicat. Lamp Oil Level] Click here
Engine oil level sensor (for 1GD-FTV) Click here
Harness or connector -
Combination meter assembly Click here
Oil maintenance warning light malfunction (for 1GD-FTV) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Check indicator/warning light Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
Combination meter assembly Click here
LED headlight indicator light malfunction (for LED Headlight) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Perform Active Test [LED Head Lamp Warning] Click here
Lighting system Click here
Combination meter assembly Click here
Headlight leveling ECU assembly Click here
Headlight leveling indicator light malfunction (for LED Headlight) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Perform Active Test [Indicat. Headlamp Auto Leveling] Click here
Automatic headlight beam level control system Click here
Combination meter assembly Click here
Headlight leveling ECU assembly Click here
DPF system warning light malfunction (w/ DPF) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Check indicator/warning light Click here
Perform Active Test [Diesel Particulate Filter Warning] Click here
ECD system Click here
Combination meter assembly Click here
POWER MODE indicator light malfunction (for 1GD-FTV, w/ ECO MODE Indicator Light) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Perform Active Test [Indicat. Lamp ECT PWR] Click here
Proceed to "Pattern Select Switch Power Mode Circuit" (for AC60E) Click here
Proceed to "Pattern Select Switch Power Mode Circuit" (for AC60F) Click here
Combination meter assembly Click here
ECM (for 1GD-FTV) Click here
POWER MODE indicator light malfunction (for 2TR-FE, w/ ECO MODE Indicator Light) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Perform Active Test [Indicat. Lamp ECT PWR] Click here
Proceed to "Pattern Select Switch Power Mode Circuit" (for AC60E) Click here
Proceed to "Pattern Select Switch Power Mode Circuit" (for AC60F) Click here
ECM (for 2TR-FE) Click here
POWER MODE indicator light malfunction (for 1GR-FE, w/ ECO MODE Indicator Light) CAN communication system (for LHD) Click here
Perform Active Test [Indicat. Lamp ECT PWR] Click here
Proceed to "Pattern Select Switch Power Mode Circuit" (for AC60F) Click here
ECM (for 1GR-FE) Click here
ECO MODE indicator light malfunction (w/ ECO MODE Indicator Light) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Perform Active Test [Indicat. ECO MODE] Click here
Combination switch assembly (eco mode switch) Click here
Harness or connector -
Combination meter assembly Click here
ECM (for 1GD-FTV) Click here
ECM (for 2TR-FE) Click here
ECM (for 1GR-FE) Click here
iMT indicator light malfunction (for Intelligent Manual Transmission) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Check indicator/warning light Click here
Perform Active Test [iMT Indicator (Green)] Click here
Perform Active Test [iMT Indicator (Yellow)] Click here
Proceed to "Pattern Select Switch iMT Mode Circuit" Click here
Combination meter assembly Click here
ECM (for 1GD-FTV) Click here
Eco driver indicator light malfunction (w/ Eco Drive Indicator Light) Check customize setting Click here
CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Check indicator/warning light Click here
Perform Active Test [Indicat. ECONO] Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
SFI system (for 2TR-FE) Click here
SFI system (for 1GR-FE) Click here
ECM (for 1GD-FTV) Click here
ECM (for 1KD-FTV) Click here
ECM (for 2TR-FE) Click here
ECM (for 1GR-FE) Click here
Combination meter assembly Click here
Open door warning light malfunction Perform Active Test [Indicat. Lamp Doors All Open] Click here
Read the Data List [Driver Side Door, Passenger Side Door, Rear Left Side Door, Rear Right Side Door] Click here
Harness or connector -
Front door courtesy switch assembly Click here
Rear door courtesy switch assembly Click here
Back door lock assembly (back door courtesy switch) Click here
Combination meter assembly Click here
Master warning light malfunction (Other systems operate normally) Check indicator/warning light Click here
Perform Active Test [Master Warning] Click here
Combination meter assembly Click here
Fuel level warning light malfunction (Fuel receiver gauge operates normally) Perform Active Test [Indicat. Lamp Fuel] Click here
Combination meter assembly Click here

Multi-information Display (for Dot Display Type)
Symptom Suspected Area Link
"OPENING" display malfunction Combination meter assembly Click here
"ENDING" display malfunction Combination meter assembly Click here
"OTHER (BLANK)" display malfunction Combination meter assembly Click here
"CURRENT FUEL CONSUMPTION" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"AVERAGE FUEL CONSUMPTION (AFTER RESET)" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"DISTANCE (RANGE)" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"AVERAGE SPEED (AFTER RESET)" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"ELAPSED TIME (AFTER RESET)" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"DRIVE INFORMATION" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"ECO DRIVING INDICATOR ZONE" display malfunction (w/ Eco Drive Indicator Light) Check customize setting Click here
CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
SFI system (for 2TR-FE) Click here
SFI system (for 1GR-FE) Click here
ECM (for 1GD-FTV) Click here
ECM (for 1KD-FTV) Click here
ECM (for 2TR-FE) Click here
ECM (for 1GR-FE) Click here
Combination meter assembly Click here
"SETTING" display malfunction Combination meter assembly Click here
"ACCELERATOR AND BRAKE PEDALS DEPRESSED SIMULTANEOUSLY" message is displayed when it should not be, not displayed when it should be, or not displayed correctly CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
SFI system (for 2TR-FE) Click here
SFI system (for 1GR-FE) Click here
Combination meter assembly Click here
"BRAKE OVERRIDE MALFUNCTION VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
SFI system (for 2TR-FE) Click here
SFI system (for 1GR-FE) Click here
Combination meter assembly Click here
"CHECK ENGINE REDUCED ENGINE POWER VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
SFI system (for 2TR-FE) Click here
SFI system (for 1GR-FE) Click here
Combination meter assembly Click here
"CHECK ENGINE VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
SFI system (for 2TR-FE) Click here
SFI system (for 1GR-FE) Click here
Combination meter assembly Click here
"REDUCED ENGINE POWER VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
SFI system (for 2TR-FE) Click here
SFI system (for 1GR-FE) Click here
Combination meter assembly Click here
"ENGINE MAINTENANCE REQUIRED VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
SFI system (for 2TR-FE) Click here
SFI system (for 1GR-FE) Click here
Combination meter assembly Click here
"WATER ACCUMULATION IN FUEL FILTER SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1GD-FTV, 1KD-FTV) Level warning switch (for 1GD-FTV) Click here
Level warning switch (for 1KD-FTV) Click here
Harness or connector -
Combination meter assembly Click here
"REPLACE FUEL FILTER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1KD-FTV) Fuel filter assembly (clogging switch) (for 1KD-FTV) Click here
Harness or connector -
Combination meter assembly Click here
"ENGINE OIL LEVEL LOW ADD OR REPLACE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (Tachometer and engine coolant temperature receiver gauge are operate normally) (for 1GD-FTV) Engine oil level sensor (for 1GD-FTV) Click here
Harness or connector -
Combination meter assembly Click here
"HEADLIGHT SYSTEM MALFUNCTION VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for LED Headlight) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Lighting system Click here
Automatic headlight beam level control system (w/ Automatic Headlight Beam Level Control System) Click here
Combination meter assembly Click here
"2WD-4WD MODE CHANGE MALFUNCTION VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Touch select 2-4 and high-low system Click here
Combination meter assembly Click here
"DIFFERENTIAL OIL TEMP HIGH COOLING TIME REQUIRED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Differential system (w/ Differential Lock) Click here
Combination meter assembly Click here
"DIFFERENTIAL OIL TEMP HIGH SHIFT TO 2WD MODE COOLING TIME REQUIRED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Differential system (w/ Differential Lock) Click here
Combination meter assembly Click here
"TRC TURNED OFF" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ VSC) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Vehicle stability control system Click here
Combination meter assembly Click here
"CRUISE CONTROL MALFUNCTION VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Cruise Control System) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Cruise control system Click here
Combination meter assembly Click here
"iMT SYSTEM MALFUNCTION VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Intelligent Manual Transmission) CAN communication system (for LHD) Click here
Manual transmission system Click here
Combination meter assembly Click here
"TRANSMISSION FLUID TEMP HIGH SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD, Automatic Transmission) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Automatic transmission system (AC60F, for 1GR-FE) Click here
Automatic transmission system (AC60F, for 1GD-FTV) Click here
Automatic transmission system (AC60F, for 2TR-FE) Click here
Combination meter assembly Click here
"OIL MAINTENANCE REQUIRED SOON" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1GD-FTV) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD System (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
Combination meter assembly Click here
"OIL MAINTENANCE REQUIRED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1GD-FTV) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD System (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
Combination meter assembly Click here
"RESETTING OIL MAINTENANCE DATA" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1GD-FTV) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD System (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
Combination meter assembly Click here
"RESETTING OF OIL MAINTENANCE DATA INCOMPLETE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1GD-FTV) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD System (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
Combination meter assembly Click here
"RESETTING OF OIL MAINTENANCE DATA COMPLETE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1GD-FTV) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD System (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, i-ART) Click here
Combination meter assembly Click here
"T-BELT MAINTENANCE REQUIRED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1KD-FTV) Combination meter assembly Click here
"RESETTING T-BELT MAINTENANCE DATA" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1KD-FTV) Combination meter assembly Click here
T-BELT maintenance mileage message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1KD-FTV) Combination meter assembly Click here
"RESETTING OF T-BELT MAINTENANCE DATA NOW POSSIBLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1KD-FTV) Combination meter assembly Click here
"RESETTING OF T-BELT MAINTENANCE DATA COMPLETE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1KD-FTV) Combination meter assembly Click here
"DPF FULL SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
Combination meter assembly Click here
"DPF FULL VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
Combination meter assembly Click here
"MANUAL REGENERATION IN PROCESS KEEP FLAMMABLES AWAY FROM VEHICLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
Combination meter assembly Click here
"DPF REGENERATION IN PROCESS" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
Combination meter assembly Click here
"DPF MANUAL REGENERATION AVAILABLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
Combination meter assembly Click here
"DPF FULL MANUAL REGENERATION REQUIRED SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
Combination meter assembly Click here

Multi-information Display (for TFT Display Type)
Symptom Suspected Area Link
"Opening" display malfunction Combination meter assembly Click here
"ECO saving" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"ECO score" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"Current fuel consumption" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"Average fuel consumption (After refuel)" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"Average fuel consumption (After start)" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"Average fuel consumption (After reset)" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"Distance (Range)" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"Average speed (After start)" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"Average speed (After reset)" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"Elapsed time (After start)" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"Elapsed time (After reset)" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"Distance (After start)" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"Idling stop time" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"Drive Information" display malfunction (Combination meter assembly operates normally) Combination meter assembly Click here
"Eco driving indicator zone" display malfunction (w/ Eco Drive Indicator Light) Check customize setting Click here
CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
SFI system (for 2TR-FE) Click here
SFI system (for 1GR-FE) Click here
ECM (for 1GD-FTV) Click here
ECM (for 1KD-FTV) Click here
ECM (for 2TR-FE) Click here
ECM (for 1GR-FE) Click here
Combination meter assembly Click here
"Other (Blank)" display malfunction Combination meter assembly Click here
"Outside temp" display malfunction Thermistor assembly (ambient temperature sensor) Click here
Harness or connector -
Combination meter assembly Click here
"Icy street warning" display malfunction Thermistor assembly (ambient temperature sensor) Click here
Harness or connector -
Combination meter assembly Click here
"Drive information tab" display malfunction Combination meter assembly Click here
"Navigation tab" display malfunction (w/ Navigation System) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Navigation system Click here
Combination meter assembly Click here
"Audio tab" display malfunction (w/ Audio and Visual System [for Radio and Display Type]) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Navigation system (w/ Navigation System) Click here
Audio and Visual System (for Radio and Display Type) Click here
Combination meter assembly Click here
"Cruise control operation guide tab" display malfunction (w/ Cruise Control System) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Cruise control system Click here
Combination meter assembly Click here
"Message tab" display malfunction Combination meter assembly Click here
"Setting tab" display malfunction Combination meter assembly Click here
"Smart Entry & Start System malfunction See owner's manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
"Steering wheel lock Press engine switch while turning wheel" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
"Depress brake and then touch key to engine switch" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System [for Automatic Transmission]) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
"Depress clutch and then touch key to engine switch" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System [for Manual Transmission]) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
"Key not detected Check key location" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
"Depress brake and then start engine" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System [for Automatic Transmission]) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
"Depress clutch and then start engine" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System [for Manual Transmission]) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
"Key battery low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
"Turn off vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
"Shift to P before exiting vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
"Power turned off to save battery" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
"Push and hold engine switch for emergency stop" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
"Shift to N and press engine switch to restart" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System [for Automatic Transmission]) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
"Depress clutch and press engine switch to restart" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System [for Manual Transmission]) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
"Key left inside vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) CAN communication system (for LHD) Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
"ACCESSORY" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
"IGNITION ON" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
"Low oil pressure Stop in a safe place See owner's manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly Engine oil pressure switch assembly (for 1GD-FTV) Click here
Engine oil pressure switch assembly (for 1KD-FTV) Click here
Engine oil pressure switch assembly (for 2TR-FE) Click here
Engine oil pressure switch assembly (for 1GR-FE) Click here
Harness or connector -
Combination meter assembly Click here
"Engine oil level low Add or replace" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (Tachometer and engine coolant temperature receiver gauge are operate normally) (for 1GD-FTV) Engine oil level sensor (for 1GD-FTV) Click here
Harness or connector -
Combination meter assembly Click here
"Transmission fluid temp high See owner's manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD, Automatic Transmission) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Automatic transmission system (AC60F, for 1GR-FE) Click here
Automatic transmission system (AC60F, for 1GD-FTV) Click here
Automatic transmission system (AC60F, for 2TR-FE) Click here
Combination meter assembly Click here
"Transmission system malfunction Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD, Automatic Transmission) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Automatic transmission system (AC60F, for 1GR-FE) Click here
Automatic transmission system (AC60F, for 1GD-FTV) Click here
Automatic transmission system (AC60F, for 2TR-FE) Click here
Combination meter assembly Click here
ECM (for 1GD-FTV) Click here
"Cruise control malfunction Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Cruise Control System) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Cruise control system Click here
Combination meter assembly Click here
"iMT system malfunction visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Intelligent Manual Transmission) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Manual transmission system Click here
Combination meter assembly Click here
"Accelerator and brake pedals depressed simultaneously" message is displayed when it should not be, not displayed when it should be, or not displayed correctly CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
SFI system (for 2TR-FE) Click here
SFI system (for 1GR-FE) Click here
Combination meter assembly Click here
"Brake override malfunction Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
SFI system (for 2TR-FE) Click here
SFI system (for 1GR-FE) Click here
Combination meter assembly Click here
"Check Engine Reduced engine power Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
SFI system (for 2TR-FE) Click here
SFI system (for 1GR-FE) Click here
Combination meter assembly Click here
"Check Engine Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
SFI system (for 2TR-FE) Click here
SFI system (for 1GR-FE) Click here
Combination meter assembly Click here
"Reduced engine power Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
SFI system (for 2TR-FE) Click here
SFI system (for 1GR-FE) Click here
Combination meter assembly Click here
"Engine maintenance required Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
ECD system (for 1KD-FTV) Click here
SFI system (for 2TR-FE) Click here
SFI system (for 1GR-FE) Click here
Combination meter assembly Click here
"Water accumulation in fuel filter See owner's manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Diesel Engine) Level warning switch (for 1GD-FTV) Click here
Level warning switch (for 1KD-FTV) Click here
Harness or connector -
Combination meter assembly Click here
"Replace fuel filter" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1KD-FTV) Fuel filter assembly (clogging switch) (for 1KD-FTV) Click here
Harness or connector -
Combination meter assembly Click here
"Headlight system malfunction Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for LED Headlight) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Lighting system Click here
Automatic headlight beam level control system Click here
Combination meter assembly Click here
"2WD-4WD mode change malfunction visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Touch select 2-4 and high-low system Click here
Combination meter assembly Click here
4 wheel drive control ECU Click here
"Differential oil temp high Cooling time required" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Differential system (w/ Differential Lock) Click here
Combination meter assembly Click here
"Differential oil temp high Shift to 2WD mode Cooling time required" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Differential system (w/ Differential Lock) Click here
Combination meter assembly Click here
"TRC turned off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ VSC) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
Vehicle stability control system Click here
Combination meter assembly Click here
"Oil maintenance required soon" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1GD-FTV) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD System (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
Combination meter assembly Click here
"Oil maintenance required" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1GD-FTV) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD System (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
Combination meter assembly Click here
"Resetting oil maintenance data" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1GD-FTV) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD System (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
Combination meter assembly Click here
"Resetting of oil maintenance data incomplete" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1GD-FTV) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD System (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
Combination meter assembly Click here
"Resetting of oil maintenance data complete" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1GD-FTV) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD System (for 1GD-FTV) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
ECD system (for 1GD-FTV, for i-ART) Click here
Combination meter assembly Click here
"T-BELT maintenance required" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1KD-FTV) Combination meter assembly Click here
"Resetting T-BELT maintenance data" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1KD-FTV) Combination meter assembly Click here
"Resetting T-BELT maintenance data" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1KD-FTV) Combination meter assembly Click here
T-BELT maintenance mileage message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1KD-FTV) Combination meter assembly Click here
"Resetting of T-BELT maintenance data now possible" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1KD-FTV) Combination meter assembly Click here
"Resetting of T-BELT maintenance data complete" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 1KD-FTV) Combination meter assembly Click here
"DPF full See owner's manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
Combination meter assembly Click here
"DPF full Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
Combination meter assembly Click here
"Manual regeneration in process Keep flammables away from vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
Combination meter assembly Click here
"DPF regeneration in process" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
Combination meter assembly Click here
"DPF manual regeneration available" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
Combination meter assembly Click here
"DPF full Manual regeneration required See owner's manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) CAN communication system (for LHD) Click here
CAN communication system (for RHD) Click here
ECD system (for 1GD-FTV, w/ DPF) Click here
Combination meter assembly Click here

Buzzer
Symptom Suspected Area Link
All buzzers do not operate normally Harness or connector -
Combination meter assembly Click here
Manual transmission reverse buzzer does not operate (for Manual Transmission [RC60/RC61]) Harness or connector -
Back-up light switch assembly (RC60/RC61) Click here
Back-up light switch assembly (RC60F/RC61F) Click here
Combination meter assembly Click here
Vehicle stability control sideways sliding warning buzzer does not operate (w/ VSC) Vehicle stability control system Click here
Combination meter assembly Click here
Temperature warning/CRAWL cancel warning buzzer does not operate (w/ VSC) Vehicle stability control system Click here
Combination meter assembly Click here
Brake system temperature rise/Active Test does not operate (w/ VSC) Vehicle stability control system Click here
Combination meter assembly Click here
Brake system low braking force warning buzzer does not operate (w/ VSC) Vehicle stability control system Click here
Combination meter assembly Click here
Seat belt warning buzzer does not operate (Front seat belt warning light operates normally) Check customize setting Click here
Combination meter assembly Click here
Brake fluid low warning buzzer does not operate (Speedometer and brake warning light are normal) Combination meter assembly Click here
Engine oil pressure warning buzzer does not operate (Speedometer, tachometer and low engine oil pressure warning light are normal) Combination meter assembly Click here
4WD warning buzzer does not operate (for 4WD) Touch select 2-4 and high-low system Click here
Combination meter assembly Click here
4 wheel drive control ECU Click here
Front differential oil temperature warning buzzer does not operate (for 4WD) Differential system (w/ Differential Lock) Click here
Combination meter assembly Click here
Door open while not in P warning buzzer does not operate (w/ Smart Entry and Start System) Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
Smart entry and start system warning buzzer does not operate (w/ Smart Entry and Start System) Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
Engine switch operation while driving warning buzzer does not operate (w/ Smart Entry and Start System) Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
Restart while driving notification buzzer does not operate (w/ Smart Entry and Start System) Smart entry and start system (for Entry Function) Click here
Smart entry and start system (for Start Function) Click here
Combination meter assembly Click here
Immobiliser certification buzzer does not operate (w/ Immobiliser System) Immobiliser system (w/ Smart Entry and Start System) Click here
Immobiliser system (w/o Smart Entry and Start System) Click here
Combination meter assembly Click here
Key reminder buzzer does not operate (w/o Smart Entry and Start System) Key reminder warning system Click here
PKB-ON driving warning buzzer does not operate (Speedometer and parking brake warning light are operate normally) Combination meter assembly Click here
Driving with door ajar warning buzzer does not operate (Open door warning light and speedometer operate normally) Combination meter assembly Click here
Fuel system warning buzzer does not operate (Fuel system warning light normally) (for Diesel Engine) Combination meter assembly Click here
Sports shift reject buzzer does not operate (for Automatic Transmission) Automatic transmission system (A750F) Click here
Automatic transmission system (AC60E, for 1GD-FTV) Click here
Automatic transmission system (AC60F, for 1GR-FE) Click here
Automatic transmission system (AC60F, for 1GD-FTV) Click here
Automatic transmission system (AC60F, for 2TR-FE) Click here
Combination meter assembly Click here
Light reminder warning buzzer does not operate (Open door warning light and taillight indicator light operate normally) Combination meter assembly Click here
MIL (Malfunction indicator lamp) buzzer does not operate (MIL [Malfunction indicator lamp] operate normally) Combination meter assembly Click here
Turn signal flasher buzzer does not operate (Turn indicator light normally) Combination meter assembly Click here
Multi-information display warning buzzer does not operate Combination meter assembly Click here

Others
Symptom Suspected Area Link
DTCs display malfunction (Other systems operate normally) Combination meter assembly Click here
"ODO/TRIP meter" display malfunction Combination meter assembly Click here
Multi-information display does not change using steering pad switch assembly Read the Data List [Multi Switch (UP), Multi Switch (Down), Multi Switch (Menu), Multi Switch (ENTER), Multi Switch (Right), Multi Switch (Left) or Multi Switch (Back)] (for TFT Display Type) Click here
Read the Data List [Multi Display Select Switch or Multi Switch (Back)] (for Dot Display Type) Click here
Steering pad switch assembly Click here
Spiral with sensor cable sub-assembly Click here
Combination meter assembly Click here
ODO/TRIP meter display does not change using trip switch Combination meter assembly Click here
Shift Indicator display malfunction (for Automatic Transmission) Perform Active Test [A/T Indicator Operation 1] Click here
Perform Active Test [A/T Indicator Operation 2] Click here
Perform Active Test [A/T Indicator Operation 3] Click here
Automatic transmission system (A750F) Click here
Automatic transmission system (AC60E) Click here
Automatic transmission system (AC60F, for 1GR-FE) Click here
Automatic transmission system (AC60F, for 1GD-FTV) Click here
Automatic transmission system (AC60F, for 2TR-FE) Click here
Combination meter assembly Click here
Meter illumination is always dark (Taillight operates normally) Harness or connector -
Combination meter assembly Click here
Meter illumination does not dim at night (Taillight operates normally) Harness or connector -
Combination meter assembly Click here
Operating light control rheostat does not change light brightness Combination meter assembly Click here
Other systems that use the speed signal do not operate normally Proceed to "Speed signal Circuit" Click here