1.INSTALL ENGINE HANGER
12361
2.INSTALL FRONT ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
Install the 2 front engine mounting insulator to the 2 front No. 1 engine mounting brackets with the 2 nuts.
12391
3.INSTALL FRONT ENGINE MOUNTING HEAT INSULATOR RH
Install the front engine mounting heat insulator RH to the front engine mounting insulator with the bolt.
82121
4.INSTALL ENGINE WIRE
Install the engine wire to the engine assembly.
11000
5.REMOVE ENGINE FROM ENGINE STAND
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Attach the engine sling device and hang the engine assembly with the chain block.
Remove the engine assembly from the engine stand.
11000
6.INSTALL ENGINE ASSEMBLY
Perform "Inspection After Repair" after replacing the engine assembly.
Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
Slowly lower the engine assembly into the engine compartment.
Install the engine assembly to the body with the 4 bolts and 4 nuts.
| *a | Front Engine Mounting Insulator
(LH Side) |
| *b | Claw (Stopper) |
|
Front |
Make sure to tighten the side with the nut.
When installing a bolt with a claw (stopper), make sure to install the bolt with the claw (stopper) as shown in the illustration so that a clearance is maintained between the claw (stopper) and the intermediate shaft.
Remove the 2 bolts and 2 engine hangers.
11355
7.INSTALL REAR END PLATE
Install the rear end plate to the cylinder block with the bolt.
Connect the No. 1 water by-pass pipe to the rear end plate with the bolt.
13405
8.INSTALL FLYWHEEL SUB-ASSEMBLY
31250
9.INSTALL CLUTCH DISC ASSEMBLY
31210
10.INSTALL CLUTCH COVER ASSEMBLY
31210
11.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY
33030
12.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY
37100
13.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
51569
14.INSTALL PROPELLER SHAFT GUARD
17410
15.INSTALL FRONT EXHAUST PIPE ASSEMBLY
16.CONNECT ENGINE WIRE
Connect the sensor bracket to the right side of the frame with the bolt.
Connect the air fuel ratio sensor connector.
Connect the wire clamp to the front engine mounting bracket LH with the bolt.
Connect the 2 connectors to the engine room relay block.
Attach the clamp.
Connect the engine wire to the engine room relay block with the nut.
Attach the 2 claws and install the No. 1 relay block cover side to the engine room relay block.
Attach the 3 claws and install the No. 1 relay block cover upper to the engine room relay block.
Attach the clamp and install the No. 2 engine wire with the bolt.
Position the No. 2 engine wire as shown in the illustration.
Attach the 2 clamps and connect the No. 2 engine wire with the 2 bolts.
Install the battery tray.
Install the battery.
Install the battery hold down clamp with the 2 nuts.
Tighten the nut and install the positive (+) battery terminal.
Position the positive (+) battery terminal as shown in the illustration.
Connect the engine room main wire to the positive (+) battery terminal with the nut.
Connect the connector to the engine room main wire.
Push the engine wire through the dash panel into the cabin.
The wire should be within the range shown in the illustration.
Connect the engine wire with the bolt.
Attach the 2 clamps and connect the 3 connectors to the instrument panel wire.
89661
17.INSTALL ECM
55550
18.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
23271H
19.CONNECT NO. 1 FUEL HOSE
23273C
20.CONNECT NO. 2 FUEL HOSE
44774
21.CONNECT UNION TO CONNECTOR TUBE HOSE
Connect the union to connector tube hose to the intake manifold, and slide the clip to secure the hose.
22.CONNECT PURGE LINE HOSE
Connect the purge line hose to the purge VSV, and slide the clip to secure the hose.
28100
23.INSTALL STARTER ASSEMBLY
88320
24.CONNECT COOLER COMPRESSOR ASSEMBLY
11452
25.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
Install a new O-ring and the engine oil level dipstick guide with the bolt.
15301
26.INSTALL ENGINE OIL LEVEL DIPSTICK
44320
27.CONNECT VANE PUMP ASSEMBLY
Connect the vane pump assembly with the 2 bolts.
Connect the power steering oil pressure switch connector.
28.CONNECT HEATER HOSE
Connect the heater water outlet hose to the heater radiator unit sub-assembly, and slide the clamp to secure the hose.
Connect the heater water inlet hose to the heater radiator unit sub-assembly, and slide the clamp to secure the hose.
16400
29.INSTALL RADIATOR ASSEMBLY
16711
30.INSTALL FAN SHROUD
16470
31.INSTALL RADIATOR RESERVOIR
16572
32.INSTALL RADIATOR HOSE OUTLET
16571
33.INSTALL RADIATOR HOSE INLET
16593
34.INSTALL NO. 1 RADIATOR AIR GUIDE
53294C
35.INSTALL RADIATOR SIDE DEFLECTOR LH
for Resin Type Bumper:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(for Resin Type Bumper)>INSTALLATION
for Steel Type Bumper:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(for Steel Type Bumper)>INSTALLATION
53293C
36.INSTALL RADIATOR SIDE DEFLECTOR RH
Use the same procedure described for the LH side.
17861
37.INSTALL INTAKE AIR CONNECTOR
17701
38.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
Install the air cleaner case sub-assembly with the 3 bolts.
Attach the 3 wire harness clamps.
17801
39.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Install the air cleaner filter element sub-assembly to the air cleaner cap sub-assembly.
17705
40.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE
Install the air cleaner cap sub-assembly with No. 1 air cleaner hose and tighten the hose clamp.
Attach the 4 clamps.
Connect the intake mass air flow meter connector and attach the 2 wire harness clamps.
53301
41.INSTALL HOOD SUB-ASSEMBLY
Install the hood sub-assembly to the 2 hood hinge assemblies with the 4 bolts.
Connect the washer nozzle hose to the hood sub-assembly.
Adjust the hood sub-assembly.
42.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
43.ADD ENGINE OIL
44.ADD ENGINE COOLANT
45.ADD MANUAL TRANSMISSION OIL
46.INSPECT FOR FUEL LEAK
47.INSPECT FOR OIL LEAK
48.INSPECT FOR COOLANT LEAK
49.INSPECT FOR EXHAUST GAS LEAK
50.INSPECT IGNITION TIMING
51.INSPECT ENGINE IDLE SPEED
52.CHECK CO/HC
22030
53.CHECK THROTTLE BODY WITH MOTOR ASSEMBLY
51441
54.INSTALL NO. 1 ENGINE UNDER COVER
51410
55.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
53882F
56.INSTALL FRONT FENDER SEAL LH
Install the front fender seal LH with the 5 new clips.
53882F
57.INSTALL FRONT FENDER SEAL RH
Install the front fender seal RH with the 5 new clips.
53735B
58.INSTALL FRONT UPPER FENDER APRON SEAL LH
Install the front upper fender apron seal LH with the 6 new clips.
53735B
59.INSTALL FRONT UPPER FENDER APRON SEAL RH
Install the front upper fender apron seal RH with the 6 new clips.