Home › Engine / Hybrid System › 1TR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › 2015.06–2016.01
RM3250E _51 Engine / Hybrid System _037998 1TR-FE ENGINE MECHANICAL _0184011 ENGINE ASSEMBLY A

1TR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of ECM Vehicle Identification Number (VIN) registration DTC P0630 is output (Click here)
Code registration
(Immobiliser system)
Engine start function See the Service Bulletin for the registration method.
Replacement of engine assembly Inspection after repair Poor idle, engine start, etc. (Click here)
·

Replacement of throttle with motor body assembly

·

Cleaning the deposits from the throttle with motor body assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft

·

Replacement of No. 2 camshaft

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of piston sub-assembly

·

Replacement of piston ring

·

Replacement of intake mass air flow meter sub-assembly

·

Replacement of fuel injector assembly

·

Replacement of fuel pump

·

Replacement of air fuel ratio sensor

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Replacement of knock sensor


Inspection after repair Poor idle, engine start, etc. (Click here)

CAUTION:
·

The engine assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.

·

The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.

·
A343690

To prevent injury due to contact with an operating fan and generator V belt or cooling fan, keep your hands and clothing away from the fan and generator V belt and cooling fan when working in the engine compartment with the engine running.

·
A343701

Do not remove the radiator cap sub-assembly, cylinder block drain cock plugs or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

·
A343693

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A350542

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 53301 7.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer nozzle hose from the hood sub-assembly.


b.

Remove the 4 bolts and hood sub-assembly from the 2 hood hinge assemblies.


Hide 17705 8.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE

a.
A346135

Disconnect the intake mass air flow meter connector and detach the 2 wire harness clamps.


b.
A346136

Detach the 4 clamps.


c.

Loosen the hose clamp and remove the air cleaner cap sub-assembly with No. 1 air cleaner hose.


Hide 17801 9.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.


Hide 17701 10.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A344949

Detach the 3 wire harness clamps.


b.

Remove the 3 bolts and air cleaner case sub-assembly.


Hide 17861 11.REMOVE INTAKE AIR CONNECTOR

Hide 53735B 12.REMOVE FRONT UPPER FENDER APRON SEAL LH

a.

Remove the 6 clips and front upper fender apron seal LH.


Hide 53735B 13.REMOVE FRONT UPPER FENDER APRON SEAL RH

a.

Remove the 6 clips and front upper fender apron seal RH.


Hide 53882F 14.REMOVE FRONT FENDER SEAL LH

a.

Remove the 5 clips and front fender seal LH.


Hide 53882F 15.REMOVE FRONT FENDER SEAL RH

a.

Remove the 5 clips and front fender seal RH.


Hide 51410 16.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51441 17.REMOVE NO. 1 ENGINE UNDER COVER

Hide 53294C 18.REMOVE RADIATOR SIDE DEFLECTOR LH

Hide 53293C 19.REMOVE RADIATOR SIDE DEFLECTOR RH

HINT:

Use the same procedure described for the LH side.


Hide 16593 20.REMOVE NO. 1 RADIATOR AIR GUIDE

Hide 16571 21.REMOVE RADIATOR HOSE INLET

Hide 16572 22.REMOVE RADIATOR HOSE OUTLET

Hide 16470 23.REMOVE RADIATOR RESERVOIR

Hide 16711 24.REMOVE FAN SHROUD

Hide 16400 25.REMOVE RADIATOR ASSEMBLY

Hide 26.DISCONNECT HEATER HOSE

a.
A355818C01
1,1.333 1.167,1.333 1.167,1.333 1.5,1.083 true 1.938,1.25 2.417,1.167 2.417,1.167 2.583,1.167 true 0.823,1.25 1.073,1.417 0.25,0.167 10 true *1 2.604,1.083 2.854,1.25 0.25,0.167 10 true *2
*1 Heater Water Outlet Hose
*2 Heater Water Inlet Hose


Slide the clamp and disconnect the heater water outlet hose from the heater radiator unit sub-assembly.


b.

Slide the clamp and disconnect the heater water inlet hose from the heater radiator unit sub-assembly.


Hide 44320 27.DISCONNECT VANE PUMP ASSEMBLY

a.

Disconnect the power steering oil pressure switch connector.


b.
A348584

Remove the 2 bolts and disconnect the vane pump assembly.

NOTICE:

Do not hit other parts with the pulley when disconnecting the vane pump assembly.


HINT:

Be sure to suspend the vane pump assembly securely.



Hide 15301 28.REMOVE ENGINE OIL LEVEL DIPSTICK

Hide 11452 29.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Remove the bolt, engine oil level dipstick guide and O-ring.

NOTICE:

Cover the engine oil level dipstick guide hole to prevent foreign matter from entering it.



Hide 88320 30.DISCONNECT COOLER COMPRESSOR ASSEMBLY

Hide 32.DISCONNECT PURGE LINE HOSE

a.
A348567

Slide the clamp and disconnect the purge line hose from the purge VSV.


Hide 44774 33.DISCONNECT UNION TO CONNECTOR TUBE HOSE

a.
A348566

Slide the clamp and disconnect the union to connector tube hose from the intake manifold.


Hide 23273C 34.DISCONNECT NO. 2 FUEL HOSE

Hide 23271H 35.DISCONNECT NO. 1 FUEL HOSE

Hide 55550 36.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 38.DISCONNECT ENGINE WIRE

a.
A355820

Detach the 2 clamps and disconnect the 3 connectors from the instrument panel wire.


b.
A355819

Remove the bolt and disconnect the engine wire.


c.
A355821

Detach the clamp and grommet and pull out the engine wire from the cabin.


d.
A355822

Disconnect the connector from the engine room main wire.


e.
A348572

Remove the nut and disconnect the engine room main wire from the positive (+) battery terminal.


f.
A348573

Loosen the nut and remove the positive (+) battery terminal.


g.
A348575

Loosen the 2 nuts and remove the battery hold down clamp.


h.

Remove the battery.


i.

Remove the battery tray.


j.
A348576

Detach the 2 clamps and remove the 2 bolts and disconnect the No. 2 engine wire.


k.
A353222

Detach the clamp and remove the bolt and No. 2 engine wire.


l.
A348579

Detach the 3 claws and remove the No. 1 relay block cover upper from the engine room relay block.


m.
A348580

Detach the 2 claws and remove the No. 1 relay block cover side from the engine room relay block.


n.
A348581

Remove the nut and disconnect the engine wire from the engine room relay block.


o.

Disconnect the 2 connectors from the engine room relay block.


p.

Detach the clamp.


q.
A348582

Remove the bolt and disconnect the wire clamp from the front engine mounting bracket LH.


r.
A348583

Disconnect the air fuel ratio sensor connector.


s.

Remove the bolt and disconnect the sensor bracket from the right side of the frame.


Hide 17410 39.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 37100 41.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 33030 42.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY

Hide 31210 43.REMOVE CLUTCH COVER ASSEMBLY

Hide 31250 44.REMOVE CLUTCH DISC ASSEMBLY

Hide 11355 46.REMOVE REAR END PLATE

a.
A350264

Remove the bolt and disconnect the No. 1 water by-pass pipe from the rear end plate.


b.

Remove the bolt and rear end plate from the cylinder block.


Hide 47.INSTALL ENGINE HANGER

a.
A348586C01
0.042,0.021 0.229,0.229 0.188,0.208 10 false *a 1.854,0.021 2.063,0.219 0.208,0.198 10 false *b
*a Rear Side
*b Front Side


Install the 2 engine hangers with the 2 bolts as shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-0C010
12281-0C030
Bolt 90119-T0388
91672-81025



Hide 48.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine assembly with a chain block.


b.
A350265

Remove the 4 bolts and 4 nuts from the body.


c.

Remove the engine assembly by operating the engine sling device and chain block.

NOTICE:
·

Make sure that the engine is clear of all wiring and hoses.

·

While lowering the engine from the vehicle, do not allow it to contact the vehicle.




Hide 49.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine to an engine stand with bolts.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.




b.

Remove the 2 bolts and 2 engine hangers.


Hide 82121 50.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine assembly.


Hide 12391 51.REMOVE FRONT ENGINE MOUNTING HEAT INSULATOR RH

a.
A348589

Remove the bolt and front engine mounting heat insulator RH from the front engine mounting insulator sub-assembly.


Hide 12361 52.REMOVE FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


a.
A350266C01
0.052,0.031 0.365,0.188 0.313,0.156 10 false *a 0.052,2.51 0.365,2.667 0.313,0.156 10 true *b
*a LH Side
*b RH Side


Remove the 2 nuts and 2 front engine mounting insulator from the 2 front No. 1 engine mounting brackets.