Home › Engine / Hybrid System › 2TR-FE LUBRICATION › OIL PUMP › from 2014.08
RM1880E _51 Engine / Hybrid System _013215 2TR-FE LUBRICATION _0068499 OIL PUMP A

2TR-FE LUBRICATION  OIL PUMP  REMOVAL  


PROCEDURE

Hide 6.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 7.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 11.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

Hide 12.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 15.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A101292

Remove the 19 bolts, 2 nuts, cylinder head cover and 2 gaskets.


Hide 20.REMOVE CRANKSHAFT PULLEY

a.
A252949C02
0.635,0.531 1.073,0.531 1.073,0.531 1.333,0.844 true 0.854,0.542 1.271,1.083 true 2.125,1.865 2.323,2.042 0.198,0.177 10 false *a 0.313,0.438 0.677,0.656 0.365,0.219 10 false SST
*a Hold
V100135

Loosen


Using SST, hold the crankshaft pulley and loosen the pulley bolt until 2 or 3 threads are screwed into the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A101289N07
0.229,1.399 0.576,1.57 0.346,0.17 10 SST 0.625,1.487 0.779,1.487 0.779,1.487 1.072,1.263 false

Using SST and the pulley bolt, remove the crankshaft pulley.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05010, 09954-05021)

HINT:

Apply lubricant to the threads and end of SST.



Hide 21.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.

Remove the drain plug and gasket.


b.

Remove the 20 bolts and 2 nuts.


c.
A099215

Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.

NOTICE:

Be careful not to damage the contact surfaces of the oil pans.



Hide 22.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A334454

Remove the 2 bolts, nut, oil strainer sub-assembly and gasket.


Hide 23.REMOVE OIL PAN SUB-ASSEMBLY

a.

Remove the 16 bolts and 2 nuts.


b.
G036411C09
0.531,1.313 0.823,1.313 0.823,1.313 1.75,1.51 true 0.344,1.208 0.625,1.479 0.281,0.271 10 false *1
*1 Protective Tape


Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block and oil pan.


HINT:

Tape the screwdriver tip before use.



Hide 25.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
G036504

Remove the 19 bolts and 2 nuts shown in the illustration.


b.
A101299C02
1.344,0.135 1.188,0.135 1.188,0.135 0.75,0.417 true 2.125,0.281 2.281,0.281 2.281,0.281 2.698,0.604 true 2.302,3.177 2.458,3.177 2.458,3.177 2.979,2.708 true 1.219,3.281 1.063,3.281 1.063,3.281 0.594,2.927 true 1.438,0.031 1.625,0.198 0.188,0.167 10 false *1 1.917,0.198 2.104,0.365 0.188,0.167 10 false *1 2.094,3.104 2.281,3.271 0.188,0.167 10 false *1 1.292,3.177 1.479,3.344 0.188,0.167 10 false *1
*1 Protective Tape


Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head, cylinder block and timing chain cover.


HINT:

Tape the screwdriver tip before use.



c.
A302630

Remove the 3 O-rings.


d.
G036021

Using a 10 mm socket hexagon wrench, remove the timing chain cover plug.


Hide 26.REMOVE ENGINE WATER PUMP ASSEMBLY

a.
A087223

Remove the 8 bolts, engine water pump and gasket.


Hide 27.REMOVE FRONT CRANKSHAFT OIL SEAL

a.
A101302C08
0.667,1.375 0.417,1.781 0.417,1.781 1.042,1.74 false 1.438,0.833 1.75,0.271 1.75,0.271 2.906,0.271 true 2.979,0.177 3.271,0.458 0.292,0.281 10 false *1 0.24,1.729 0.573,1.969 0.333,0.24 10 false *2
*1 Protective Tape
*2 Wooden Block


Place the timing chain cover on wooden blocks.


b.

Using a screwdriver pry out the front crankshaft oil seal.

HINT:

Tape the screwdriver tip before use.