Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY
RM1880E _51 Engine / Hybrid System _013210 2TR-FE ENGINE MECHANICAL _0068470 ENGINE ASSEMBLY A

2TR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 6.REMOVE MANUAL TRANSMISSION OIL (for Manual Transmission)

Hide 7.DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

Hide 8.REMOVE INTAKE AIR CONNECTOR AND AIR CLEANER ASSEMBLY

A253052

a.

Disconnect the vacuum hose.


b.

Disconnect the No. 2 PCV hose.


c.

Disconnect the mass air flow meter connector and detach the wire harness clamps.


d.

Loosen the hose clamp and remove the 4 bolts, air cleaner and intake air connector assembly.


Hide 10.DISCONNECT RADIATOR HOSE INLET

Hide 11.DISCONNECT RADIATOR HOSE OUTLET

Hide 14.REMOVE FAN PULLEY

Hide 15.DISCONNECT OIL COOLER INLET HOSE (for Automatic Transmission)

Hide 16.DISCONNECT OIL COOLER OUTLET HOSE (for Automatic Transmission)

Hide 18.DISCONNECT HEATER WATER HOSE

a.
A257561
0.073,0.063 0.302,0.25 0.229,0.188 10 false *A 0.073,2.521 0.302,2.708 0.229,0.188 10 false *B
*A for LHD
*B for RHD


Disconnect the heater water inlet hose and heater water outlet hose from the heater pipe.


Hide 19.DISCONNECT HOSE

A302607

a.

Disconnect the vacuum hose (for the brake master cylinder).


b.

Disconnect the purge line hose.


Hide 22.DISCONNECT ENGINE WIRE

a.
A257562
0.099,0.035 0.293,0.204 0.194,0.17 10 *A 0.099,2.349 0.293,2.518 0.194,0.17 10 *B
*A for LHD
*B for RHD


Disconnect the ECM connectors from the cabin.

i.

Remove the glove compartment door.


ii.

Disconnect the 4 ECM connectors.



b.

Detach the wire harness clamp.


c.

Remove the bolt and disconnect the ground wire.


d.

Pull out the engine wire from the cabin.


e.

Disconnect the heated oxygen sensor connector.


f.

Remove the bolt and disconnect the sensor bracket from the right side of the frame.


g.
A250528

Remove the bolt and disconnect the ground wire from the left side of the frame.


h.

Remove the nut and disconnect the ground wire from the body.


i.

Remove the engine room relay block cover (upper).


j.
A302608
2.802,1.135 3.115,1.292 0.313,0.156 10 false *a 2.552,1.875 2.865,2.031 0.313,0.156 10 false *a 0.417,1.063 0.729,1.219 0.313,0.156 10 false *a
*a Pull


Remove the engine room relay block cover (side).

i.

Using a screwdriver, detach the 4 claws and remove the relay block cover.

HINT:

Tape the screwdriver tip before use.




k.

Remove the nut and disconnect the cable from the engine room junction block.


l.

Disconnect the 2 engine room junction block connectors and wire clamp.


m.

Remove the bolt and disconnect the wire clamp from the front engine mounting bracket LH.


Hide 23.DISCONNECT VANE PUMP ASSEMBLY

a.

Disconnect the oil pressure switch connector.


b.
A099199

Remove the 2 bolts and disconnect the vane pump from the engine.


c.

Support the vane pump securely.


Hide 24.REMOVE ENGINE OIL LEVEL DIPSTICK

Hide 25.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Remove the bolt, engine oil level dipstick guide and O-ring.

NOTICE:

Cover the dipstick guide hole to prevent foreign matter from entering it.



Hide 27.REMOVE HOOD ASSEMBLY

A237711

a.

Disconnect the washer nozzle hose.


b.

Remove the 4 bolts and hood.

NOTICE:

Be careful not to damage the vehicle.



Hide 28.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 29.REMOVE COWL PANEL SUB-ASSEMBLY

a.

Remove the 9 bolts and cowl panel.


Hide 31.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 33.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)

Hide 34.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

Hide 35.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.


a.

Remove the 4 bolts and rear No. 1 engine mounting insulator.


Hide 36.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 37.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 38.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

Hide 39.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

Hide 40.REMOVE REAR END PLATE

a.

Remove the bolt and disconnect the No. 1 water by-pass pipe from the rear end plate.


b.

Remove the bolt and rear end plate.


Hide 41.INSTALL ENGINE HANGER

a.
A099202
0.042,0.052 0.354,0.302 0.313,0.25 10 false *a 1.75,0.052 2.042,0.292 0.292,0.24 10 false *b
*a Rear Side
*b Front Side


Install 2 engine hangers with 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-0C010
Bolt 90105-T0129



Hide 42.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device to the engine hangers.


b.
G037190

Remove the 4 bolts and 4 nuts holding the engine mounting brackets to the frame.


c.
A302609
1.24,0.552 1.24,0.479 false
V100135

Lift


Lift the engine out of the vehicle slowly and carefully.

NOTICE:

Make sure to disconnect all the wires, hoses and cables from the engine. Keep the disconnected wires, hoses and cables off of the engine.



Hide 43.INSTALL ENGINE TO ENGINE STAND

a.

Install the engine to an engine stand with bolts.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.




b.

Remove the 2 bolts and 2 engine hangers.