Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261015 PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System) J

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)  "CHK" message(s) are displayed on the SIGNAL CHECK screen.  


DESCRIPTION

On the SIGNAL CHECK screen, it is possible to check if the signals sent to the parking assist ECU are normal (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>DTC CHECK / CLEAR).

HINT:
·

On the SIGNAL CHECK screen, "OK" (blue) is displayed for items with a normal inspection result or input state.

·

On the SIGNAL CHECK screen, "CHK" (red) is displayed for items with an abnormal inspection result or input state.

·

Displayed items may differ depending on vehicle specifications.



Item Signal Input Method Detail DTC Output when Abnormal Result is Displayed Signal Receiver
CAN CAN communication CAN communication signal DTC is output Related ECUs
CAMERA SW Vehicle wire harness Steering pad switch assembly (wide view front and side monitor switch) signal input DTC is not output Steering pad switch assembly (wide view front and side monitor switch)
MIRROR SW Vehicle wire harness Outer rear view mirror retract signal input DTC is not output Main body ECU (Multiplex network body ECU)
SHIFT Vehicle wire harness Shift signal input DTC is output Park/neutral position switch assembly (for Automatic Transmission)
Back-up light switch assembly (for Manual Transmission)
HANDLE CAN communication Steering position signal input DTC is output ECM
BODY CAN communication Body size signal DTC is output ECM
DEST CAN communication Destination information signal input DTC is output ECM
D-CAM SET Vehicle wire harness Driver side television camera feedback signal DTC is output Individual setting
T/M CAN communication Transmission type signal DTC is output ECM

WIRING DIAGRAM

E323965E03
5.688,5.885 6.99,6.094 1.302,0.208 10 false Parking Assist ECU 5.688,5.698 5.906,5.906 0.219,0.208 10 false I6 3.365,6 4.49,6.365 1.125,0.365 10 false Spiral Cable Sub-assembly 0.563,6.188 1.979,6.552 1.417,0.365 10 false Driving Support Switch Control ECU 0.563,6.01 1.583,6.219 1.021,0.208 10 false G163*1, G76*2 0.5,4.833 2.458,5.042 1.958,0.208 10 false Steering Pad Switch Assembly 2.948,2.083 5.104,2.458 2.156,0.375 10 false Back-up Light Switch Assembly*2 0.156,6.823 2.115,7.031 1.958,0.208 10 false *1: for Automatic Transmission 0.156,7.094 2.115,7.302 1.958,0.208 10 false *2: for Manual Transmission 2.948,1.917 4.073,2.125 1.125,0.208 10 false C41*3, C160*4 2.813,3.219 5.531,3.594 2.719,0.375 10 false Park/Neutral Position Switch Assembly*1 2.813,3.052 3.271,3.26 0.458,0.208 10 false C159 0.229,0.938 0.542,1.146 0.313,0.208 10 false G11 2.125,1.688 2.698,2.063 0.573,0.375 10 false ECU-IG NO.1 0.281,1.531 1.656,1.74 1.375,0.208 10 false from IG1 NO.1 Relay 0.229,1.073 2.188,1.281 1.958,0.208 10 false Outer Mirror Switch Assembly 0.771,7.438 2.729,7.646 1.958,0.208 10 false : CAN Communication Line 5.865,1.552 6.323,1.76 0.458,0.208 10 false REV 5.865,0.604 6.323,0.813 0.458,0.208 10 false MPOS 1.667,0.604 1.917,0.813 0.25,0.208 10 false MF 5.865,3.917 6.323,4.125 0.458,0.208 10 false BLSW 4.115,3.833 4.427,4 0.313,0.167 10 false +DP 3.427,3.833 3.74,4 0.313,0.167 10 false +DP 3.427,4.396 3.896,4.563 0.469,0.167 10 false GND1 3.427,5.51 3.896,5.677 0.469,0.167 10 false GND1 1.531,5.51 1.927,5.677 0.396,0.167 10 false SWI2 0.594,5.51 0.99,5.677 0.396,0.167 10 false GND 5.646,3.729 5.865,3.917 0.219,0.188 10 false 8 5.604,1.417 5.823,1.604 0.219,0.188 10 false 27 4.51,1.417 5.052,1.604 0.542,0.188 10 false 2*3, 1*4 2.865,1.417 3.458,1.604 0.594,0.188 10 false 1*3, 2*4 4.229,2.583 4.458,2.792 0.229,0.208 10 false RL 3.438,2.583 3.667,2.792 0.229,0.208 10 false RB 4.51,2.542 4.729,2.729 0.219,0.188 10 false 1 3.24,2.542 3.458,2.729 0.219,0.188 10 false 2 5.646,0.49 5.865,0.677 0.219,0.188 10 false 5 1.979,0.49 2.198,0.677 0.219,0.188 10 false 14 4.51,3.896 4.833,4.073 0.323,0.177 10 false G40 3.063,5.573 3.385,5.75 0.323,0.177 10 false G40 3.125,4.458 3.385,4.635 0.26,0.177 10 false z8 3.125,3.885 3.385,4.063 0.26,0.177 10 false z8 4.594,3.708 4.813,3.896 0.219,0.188 10 false 3 3.156,3.698 3.375,3.885 0.219,0.188 10 false 7 3.167,4.25 3.385,4.438 0.219,0.188 10 false 3 3.094,5.375 3.313,5.563 0.219,0.188 10 false 10 1.979,5.302 2.333,5.667 0.354,0.365 10 false 14*1, 4*2 0.229,5.313 0.604,5.677 0.375,0.365 10 false 7*1, 16*2 2.396,6.833 4.354,7.042 1.958,0.208 10 false *3: for 1GR-FTV 2.396,7.125 4.354,7.333 1.958,0.208 10 false *4: for 1KD-FTV, 1GD-FTV

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the navigation receiver assembly*1 or radio and display receiver assembly*2 after the battery cable is disconnected, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>CALIBRATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>CALIBRATION).



*1: for Navigation Receiver Type

*2: for Radio and Display Type


PROCEDURE

1.CHECK DISPLAY CHECK MODE
a.
E285877

Check which items display on the SIGNAL CHECK screen.


Result
Result Proceed to
"CAMERA SW" displays "CHK" (red) A
"SHIFT" displays "CHK" (red) (for Automatic Transmission) B
"SHIFT" displays "CHK" (red) (for Manual Transmission) C
"MIRROR SW" displays "CHK" (red) D
"CAN" displays "CHK" (red) E
"HANDLE", "BODY", "DEST", "T/M" or "D-CAM SET" displays unmatched information E


A

2.INSPECT STEERING PAD SWITCH ASSEMBLY (WIDE VIEW FRONT AND SIDE MONITOR SWITCH)

B

7.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

9.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY

D

11.INSPECT OUTER MIRROR SWITCH ASSEMBLY

E

2.INSPECT STEERING PAD SWITCH ASSEMBLY (WIDE VIEW FRONT AND SIDE MONITOR SWITCH)
a.

Remove the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>REMOVAL).


b.

Inspect the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>INSPECTION).



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.

Inspect the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - PARKING ASSIST ECU)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - PARKING ASSIST ECU)
a.

Disconnect the G40 spiral cable sub-assembly connector.


b.

Disconnect the I6 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G40-3 (+DP) - I6-8 (BLSW) Always Below 1 Ω
G40-3 (+DP) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT SWITCH CONTROL ECU - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT SWITCH CONTROL ECU - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND)
a.

for Automatic Transmission:

i.

Disconnect the G163 driving support switch control ECU connector.


ii.

Disconnect the G40 spiral cable sub-assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G163-14 (SWI2) - G40-10 (GND1) Always Below 1 Ω
G163-14 (SWI2) - Body ground Always 10 kΩ or higher
G163-7 (GND) - Body ground Always Below 1 Ω




b.

for Manual Transmission:

i.

Disconnect the G76 driving support switch control ECU connector.


ii.

Disconnect the G40 spiral cable sub-assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G76-4 (SWI2) - G40-10 (GND1) Always Below 1 Ω
G76-4 (SWI2) - Body ground Always 10 kΩ or higher
G76-16 (GND) - Body ground Always Below 1 Ω





OK

6.CHECK DRIVING SUPPORT SWITCH CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK DRIVING SUPPORT SWITCH CONTROL ECU
a.

Replace the driving support switch control ECU with a new or normally functioning one (See page Steering>STEERING COLUMN>DRIVING SUPPORT SWITCH CONTROL ECU>REMOVAL).


b.

Check that "CAMERA SW" displays "OK" on the SIGNAL CHECK screen.

OK:

"CAMERA SW" displays "OK".




OK

END (DRIVING SUPPORT SWITCH CONTROL ECU IS DEFECTIVE)

NG

7.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

A

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - PARKING ASSIST ECU AND BATTERY)

B

C

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - PARKING ASSIST ECU AND BATTERY)
a.

Disconnect the C159 park/neutral position switch assembly connector.


b.

Disconnect the I6 parking assist ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C159-2 (RB) - Body ground Engine switch on (IG) 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C159-1 (RL) - I6-27 (REV) Always Below 1 Ω
C159-1 (RL) - Body ground Always 10 kΩ or higher



Result
Proceed to Result
OK (for LHD) A
OK (for RHD) B
NG C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY
a.

Remove the back-up light switch assembly (See page Drivetrain>RA61F (MANUAL TRANSMISSION / TRANSAXLE)>BACK-UP LIGHT SWITCH>REMOVAL).


b.

Inspect the back-up light switch assembly (See page Drivetrain>RA61F (MANUAL TRANSMISSION / TRANSAXLE)>BACK-UP LIGHT SWITCH>INSPECTION).



OK

10.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - PARKING ASSIST ECU AND BATTERY)

NG

10.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - PARKING ASSIST ECU AND BATTERY)
a.

for 1KD-FTV, 1GD-FTV:

i.

Disconnect the C160 back-up light switch assembly connector.


ii.

Disconnect the I6 parking assist ECU connector.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C160-1 - Body ground Engine switch on (IG) 11 to 14 V



iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C160-2 - I6-27 (REV) Always Below 1 Ω
C160-2 - Body ground Always 10 kΩ or higher




b.

for 1GR-FE:

i.

Disconnect the C41 back-up light switch assembly connector.


ii.

Disconnect the I6 parking assist ECU connector.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C41-2 - Body ground Engine switch on (IG) 11 to 14 V



iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-1 - I6-27 (REV) Always Below 1 Ω
C41-1 - Body ground Always 10 kΩ or higher




Result
Proceed to Result
OK (for LHD) A
OK (for RHD) B
NG C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT OUTER MIRROR SWITCH ASSEMBLY
a.

Remove the outer mirror switch assembly (See page Vehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL).


b.

Inspect the outer mirror switch assembly (See page Vehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>INSPECTION).



OK

12.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - PARKING ASSIST ECU)

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - PARKING ASSIST ECU)
a.

Disconnect the G11 outer mirror switch assembly connector.


b.

Disconnect the I6 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G11-14 (MF) - I6-5 (MPOS) Always Below 1 Ω
G11-14 (MF) - Body ground Always 10 kΩ or higher



Result
Proceed to Result
OK (for LHD) A
OK (for RHD) B
NG C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR