There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
| Symptom | Trouble Area |
|---|---|
| The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω. | ·
Short between CAN bus lines and GND ·
ECM ·
Brake actuator assembly (skid control ECU)*1 ·
Master cylinder solenoid (skid control ECU)*2 ·
Four wheel drive control ECU ·
Network gateway ECU*3 ·
Power steering ECU assembly*4 ·
Air conditioning amplifier assembly ·
Radio and display receiver assembly*5 ·
Spiral cable sub-assembly (steering angle sensor)*4 ·
Yaw rate sensor assembly ·
Center airbag sensor assembly ·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly ·
No. 1 junction connector ·
No. 2 junction connector ·
No. 3 junction connector ·
No. 4 junction connector*1 ·
No. 5 junction connector*2 |
*1: for 2TR-FE, 5L-E
*2: for 1KD-FTV
*3: w/ Network Gateway ECU
*4: w/ Vehicle Stability Control System
*5: w/ Audio and Visual System (for Radio and Display Type)
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
NEXT
Disconnect the G94 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G48-6 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G48-14 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
OK
NG
Reconnect the G94 No. 3 junction connector.
NEXT
Disconnect the G97 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G48-6 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G48-14 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G97-2 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G97-13 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
For vehicles without a network gateway ECU, go to "Check for Short to GND in CAN Bus Wire (No. 1 Junction Connector - Air Conditioning Amplifier Assembly)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G97-3 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G97-14 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G97-4 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G97-15 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
For vehicles without a vehicle stability control system, go to "Check for Short to GND in CAN Bus Wire (No. 1 Junction Connector - ECM)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G97-5 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G97-16 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G97-6 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G97-17 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1KD-FTV) | B |
| NG (for 2TR-FE, 5L-E) | C |
A
B
C
Reconnect the G97 No. 1 junction connector.
NEXT
Disconnect the G53 four wheel drive control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G53-19 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G53-20 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Four Wheel Drive Control ECU) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G97 No. 1 junction connector.
NEXT
Disconnect the G155 network gateway ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G155-16 (CA1H) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G155-15 (CA1L) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Network Gateway ECU) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G97 No. 1 junction connector.
NEXT
Disconnect the G25 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G25-11 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G25-12 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G97 No. 1 junction connector.
NEXT
Disconnect the G46 power steering ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G46-1 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G46-2 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Power Steering ECU Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G97 No. 1 junction connector.
NEXT
Disconnect the G58 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G58-35 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G58-36 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to ECM) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G97 No. 1 junction connector.
NEXT
Disconnect the A72 No. 4 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A72-9 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| A72-20 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 4 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A72-11 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| A72-22 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 4 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A72-10 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| A72-21 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 4 Junction Connector) |
| *b | Front view of DLC3 |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 2TR-FE) | B |
| NG (for 5L-E) | C |
A
B
C
Reconnect the A74 No. 4 junction connector.
NEXT
Disconnect the A6 brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A6-25 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| A6-14 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU]) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the A74 No. 4 junction connector.
NEXT
Disconnect the G181 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G181-13 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G181-14 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to ECM) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the A74 No. 4 junction connector.
NEXT
Disconnect the G183 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G183-25 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G183-31 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to ECM) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G97 No. 1 junction connector.
NEXT
Disconnect the G100 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G100-1 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G100-12 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G48-6 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G48-14 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
OK
NG
For vehicles without an audio and visual system (for radio and display type), go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - Steering Angle Sensor)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G100-2 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G100-13 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
For vehicles without a vehicle stability control system, go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - Yaw Rate Sensor Assembly)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G100-3 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G100-14 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G100-4 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G100-15 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G100-5 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G100-16 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G100 No. 2 junction connector.
NEXT
Disconnect the H51 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H51-9 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| H51-10 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
| *b | Front view of DLC3 |
OK
(See pageAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL)
NG
Reconnect the G100 No. 2 junction connector.
NEXT
Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G33-4 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G33-3 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor]) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G100 No. 2 junction connector.
NEXT
Disconnect the G52 yaw rate sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G52-3 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G52-2 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Yaw Rate Sensor Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G100 No. 2 junction connector.
NEXT
Disconnect the G1 center airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G1-13 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G1-22 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Center Airbag Sensor Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G100 No. 2 junction connector.
NEXT
Disconnect the G94 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G94-1 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G94-12 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G94-3 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G94-14 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G94-6 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G94-17 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G94-2 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G94-13 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *A | for 1KD-FTV |
| *B | for 2TR-FE, 5L-E |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 2TR-FE, 5L-E) | B |
| NG (for 1KD-FTV) | C |
A
B
C
Reconnect the G94 No. 3 junction connector.
NEXT
Disconnect the G64 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G64-14 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G64-13 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G94 No. 3 junction connector.
NEXT
Disconnect the G6 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G6-40 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G6-39 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G94 No. 3 junction connector.
NEXT
Disconnect the A73 No. 5 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A73-9 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| A73-20 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 5 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A73-11 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| A73-22 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 5 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A73-10 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| A73-21 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 5 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the A73 No. 5 junction connector.
NEXT
Disconnect the A7 master cylinder solenoid (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A7-11 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| A7-25 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU]) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the A73 No. 5 junction connector.
NEXT
Disconnect the G6 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G6-40 (CANH) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| G6-39 (CANL) - G48-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
| *b | Front view of DLC3 |
OK
NG