Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261034 CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)  Open in One Side of CAN Branch Line  


DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).

Symptom Trouble Area
2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen.
·

Brake actuator assembly (skid control ECU)*1

·

Master cylinder solenoid (skid control ECU)*2

·

Main body ECU (multiplex network body ECU)

·

Center airbag sensor assembly

·

Spiral cable sub-assembly (steering angle sensor)*2

·

Radio and display receiver assembly*3

·

Four wheel drive control ECU

·

Air conditioning amplifier assembly

·

Power steering ECU assembly*4

·

Network gateway ECU*5

·

Yaw rate sensor assembly



*1: w/o Vehicle Stability Control System

*2: w/ Vehicle Stability Control System (for Hydraulic Brake Booster)

*3: w/ Audio and Visual System (for Radio and Display Type)

*4: for 1KD-FTV

*5: w/ TOYOTA Parking Assist-sensor System (for 4 Sensor Type)


WIRING DIAGRAM

C292163E01
5.675,6.228 5.770,6.379 0.095,0.151 10 6 5.582,6.661 5.769,6.812 0.187,0.151 10 14 2.84,7.522 3.197,7.706 0.357,0.183 10 G132 2.84,7.67 4.467,7.827 1.627,0.157 10 No. 2 Junction Connector 5.881,0.627 6.305,0.781 0.423,0.153 10 CANH 5.881,1.262 6.305,1.408 0.423,0.147 10 CANL 5.658,1.551 6.018,1.724 0.359,0.173 10 G6 5.658,1.712 6.888,2.064 1.230,0.351 10 Combination Meter Assembly 3.92,0.627 4.108,0.778 0.187,0.151 10 10 3.92,1.066 4.108,1.217 0.187,0.151 10 21 3.92,2.506 4.108,2.657 0.187,0.151 10 9 3.92,2.928 4.108,3.079 0.187,0.151 10 20 3.92,4.376 4.108,4.527 0.187,0.151 10 8 3.92,4.798 4.108,4.949 0.187,0.151 10 19 3.08,0.627 3.258,0.778 0.178,0.151 10 11 3.08,1.066 3.268,1.217 0.187,0.151 10 22 3.172,4.376 3.269,4.527 0.097,0.151 10 2 3.08,4.798 3.268,4.949 0.187,0.151 10 13 3.92,6.228 4.108,6.379 0.187,0.151 10 4 3.92,6.661 4.108,6.812 0.187,0.151 10 15 3.172,6.228 3.269,6.379 0.097,0.151 10 5 3.08,6.651 3.268,6.801 0.187,0.151 10 16 0.898,1.184 1.293,1.321 0.396,0.136 10 CANL 0.87,0.73 1.293,0.867 0.423,0.136 10 CANH 1.411,0.627 1.599,0.778 0.187,0.151 10 25 1.411,1.066 1.599,1.217 0.187,0.151 10 14 0.353,1.551 0.710,1.734 0.357,0.183 10 A6 0.353,1.712 2.184,2.079 1.832,0.367 10 Brake Actuator Assembly (Skid Control ECU)*1 0.898,3.065 1.293,3.202 0.396,0.136 10 CANL 0.87,2.611 1.293,2.748 0.423,0.136 10 CANH 1.411,2.508 1.599,2.659 0.187,0.151 10 11 1.411,2.947 1.599,3.098 0.187,0.151 10 25 0.353,3.41 0.710,3.593 0.357,0.183 10 A7 0.353,3.569 2.184,3.935 1.832,0.367 10 Master Cylinder Solenoid (Skid Control ECU)*2 0.898,4.94 1.293,5.076 0.396,0.136 10 CANL 0.87,4.486 1.293,4.623 0.423,0.136 10 CANH 1.411,4.376 1.593,4.527 0.182,0.151 10 14 1.411,4.798 1.599,4.949 0.187,0.151 10 13 0.311,5.246 0.636,5.418 0.326,0.171 10 G64 0.311,5.397 1.976,5.727 1.665,0.330 10 Main Body ECU (Multiplex Network Body ECU) 5.881,6.793 6.277,6.929 0.396,0.136 10 CANL 5.881,6.339 6.305,6.475 0.423,0.136 10 CANH 0.898,6.793 1.293,6.929 0.396,0.136 10 CANL 0.87,6.339 1.293,6.475 0.423,0.136 10 CANH 1.411,6.229 1.593,6.379 0.182,0.151 10 13 1.411,6.651 1.599,6.801 0.187,0.151 10 22 0.319,7.099 0.645,7.271 0.326,0.171 10 G1 0.319,7.25 1.714,7.579 1.394,0.329 10 Center Airbag Sensor Assembly 0.174,8.015 3.965,8.164 3.790,0.149 10 *1: w/o Vehicle Stability Control System 0.174,8.323 4.506,8.472 4.332,0.149 10 *2: w/ Vehicle Stability Control System (for Hydraulic Brake Booster) 5.582,0.627 5.778,0.778 0.196,0.151 10 40 5.582,1.066 5.778,1.217 0.196,0.151 10 39 2.844,3.569 4.476,3.752 1.632,0.183 10 No. 1 Junction Connector 2.844,3.41 3.194,3.593 0.350,0.183 10 A72 6.056,7.263 6.434,7.453 0.379,0.190 10 DLC3 6.061,7.113 6.387,7.284 0.326,0.171 10 G48

C292164E01
5.675,0.743 5.770,0.894 0.095,0.151 10 4 5.675,1.176 5.770,1.327 0.095,0.151 10 3 3.92,1.747 4.108,1.898 0.187,0.151 10 1 3.92,2.169 4.108,2.320 0.187,0.151 10 12 5.32,1.767 7.043,2.130 1.723,0.363 10 Spiral Cable Sub-assembly (Steering Angle Sensor)*2 3.92,0.743 4.108,0.894 0.187,0.151 10 7 3.92,1.176 4.108,1.327 0.187,0.151 10 18 3.172,0.743 3.269,0.894 0.097,0.151 10 9 3.08,1.166 3.268,1.316 0.187,0.151 10 20 5.32,1.615 5.645,1.786 0.326,0.171 10 G33 5.881,1.308 6.277,1.444 0.396,0.136 10 CANL 5.881,0.854 6.305,0.990 0.423,0.136 10 CANH 0.898,1.308 1.293,1.444 0.396,0.136 10 CANL 0.87,0.854 1.293,0.990 0.423,0.136 10 CANH 1.411,0.743 1.593,0.894 0.182,0.151 10 9 1.411,1.166 1.599,1.316 0.187,0.151 10 10 0.319,1.614 0.645,1.785 0.326,0.171 10 H51 0.319,1.765 2.089,2.094 1.769,0.329 10 Radio and Display Receiver Assembly*3 1.428,3.602 1.614,3.753 0.186,0.151 10 19 1.428,4.048 1.614,4.198 0.186,0.151 10 20 3.914,3.602 4.102,3.753 0.187,0.151 10 1 3.914,4.057 4.102,4.208 0.187,0.151 10 12 3.914,5.495 4.102,5.646 0.187,0.151 10 4 3.914,5.94 4.102,6.091 0.187,0.151 10 15 5.603,5.495 5.784,5.646 0.181,0.151 10 11 5.591,5.94 5.778,6.091 0.187,0.151 10 12 1.439,5.495 1.621,5.646 0.181,0.151 10 1 1.428,5.94 1.615,6.091 0.187,0.151 10 2 3.159,3.602 3.269,3.753 0.110,0.151 10 3 3.087,4.048 3.274,4.198 0.187,0.151 10 14 2.801,2.655 3.158,2.838 0.357,0.183 10 G132 2.801,2.831 4.433,3.014 1.632,0.183 10 No. 2 Junction Connector 2.801,7.101 3.158,7.284 0.357,0.183 10 G134 2.801,7.277 4.433,7.460 1.632,0.183 10 No. 3 Junction Connector 0.279,4.525 0.676,4.691 0.396,0.166 10 G53 5.406,6.389 5.803,6.555 0.396,0.166 10 G25 5.406,6.557 7.021,6.887 1.615,0.330 10 Air Conditioning Amplifier Assembly 0.318,6.41 0.758,6.587 0.440,0.177 10 G46 0.318,6.572 1.640,6.941 1.322,0.369 10 Power Steering ECU Assembly*4 0.279,4.686 2.244,5.049 1.965,0.363 10 Four Wheel Drive Control ECU 3.159,5.495 3.291,5.645 0.132,0.150 10 5 3.087,5.941 3.274,6.091 0.187,0.151 10 16 0.901,3.716 1.324,3.853 0.423,0.137 10 CANH 0.901,4.167 1.324,4.304 0.423,0.137 10 CANL 0.901,5.598 1.324,5.735 0.423,0.137 10 CANH 0.901,6.049 1.324,6.186 0.423,0.137 10 CANL 5.879,5.598 6.302,5.735 0.423,0.137 10 CANH 5.873,6.049 6.297,6.186 0.423,0.137 10 CANL 0.254,8.085 4.186,8.248 3.932,0.163 10 *3: w/ Audio and Visual System (for Radio and Display Type) 0.254,8.399 4.186,8.563 3.932,0.163 10 *4: for 1KD-FTV 0.254,7.771 4.491,7.934 4.238,0.163 10 *2: w/ Vehicle Stability Control System (for Hydraulic Brake Booster)

C334434E01
5.418,2.723 5.743,2.877 0.324,0.154 10 36*4 5.413,2.258 5.748,2.411 0.334,0.153 10 35*4 5.425,2.485 5.736,2.624 0.310,0.139 10 G58 5.425,2.943 5.736,3.082 0.310,0.139 10 G58 4.963,2.723 5.287,2.877 0.324,0.154 10 31*6 4.958,2.258 5.292,2.411 0.334,0.153 10 25*6 4.945,2.485 5.305,2.624 0.359,0.139 10 G183 4.945,2.943 5.305,3.082 0.359,0.139 10 G183 3.914,2.393 4.102,2.544 0.187,0.151 10 2 3.914,2.834 4.102,2.985 0.187,0.151 10 13 1.288,2.383 1.424,2.533 0.136,0.150 10 3 1.288,2.828 1.402,2.979 0.115,0.151 10 2 3.159,2.383 3.291,2.533 0.132,0.150 10 8 3.087,2.834 3.274,2.985 0.187,0.151 10 19 1.288,0.409 1.514,0.559 0.227,0.150 10 16 1.288,0.854 1.477,1.005 0.189,0.151 10 15 0.177,3.288 0.535,3.472 0.357,0.183 10 G52 0.177,1.328 0.617,1.505 0.440,0.177 10 G155 0.177,1.49 2.055,1.859 1.878,0.369 10 Network Gateway ECU*5 3.159,0.409 3.291,0.559 0.132,0.150 10 6 3.087,0.854 3.274,1.005 0.187,0.151 10 17 5.873,2.375 6.297,2.528 0.423,0.153 10 CANH 5.873,3.02 6.297,3.167 0.423,0.147 10 CANL 6.022,3.294 6.376,3.460 0.354,0.166 10 ECM 2.801,3.277 3.158,3.460 0.357,0.183 10 G134 2.801,3.452 4.433,3.635 1.632,0.183 10 No. 3 Junction Connector 0.177,3.458 2.026,3.789 1.849,0.331 10 Yaw Rate Sensor Assembly 0.796,0.513 1.184,0.650 0.389,0.137 10 CA1H 0.817,0.964 1.185,1.101 0.368,0.137 10 CA1L 0.761,2.487 1.184,2.625 0.423,0.137 10 CANH 0.761,2.938 1.184,3.075 0.423,0.137 10 CANL 0.201,4.157 4.364,4.321 4.163,0.163 10 *5: w/ TOYOTA Parking Assist-sensor System (for 4 Sensor Type) 0.198,3.874 1.408,4.037 1.210,0.163 10 *4: for 1KD-FTV 0.214,4.441 1.424,4.604 1.210,0.163 10 *6: for 5L-E

CAUTION / NOTICE / HINT

HINT:
·

Perform the following inspection for the ECUs (sensors) which are not displayed on the intelligent tester. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.

·

Do not remove the combination meter assembly and ECM, as they are the end parts of the circuit. If removed, CAN communication will not be possible.

·

The open circuit confirmation of the combination meter assembly, ECM and CAN main wire is performed in the Check CAN Bus Line procedure of "How to Proceed with Troubleshooting". This inspection only has procedures for checking for an open circuit on one side of the CAN branch wire.



PROCEDURE

1.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU)
a.

Disconnect the A6 brake actuator assembly (skid control ECU)*1 or A7 master cylinder solenoid (skid control ECU)*2 connector.

*1: w/o Vehicle Stability Control System

*2: w/ Vehicle Stability Control System (for Hydraulic Brake Booster)



b.

Select "Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Skid Control (ABS/VSC/TRAC)" is not displayed on the intelligent tester (w/o Vehicle Stability Control System) A
"Skid Control (ABS/VSC/TRAC)" is not displayed on the intelligent tester (w/ Vehicle Stability Control System [for Hydraulic Brake Booster]) B
Several ECUs and sensors in addition to "Skid Control (ABS/VSC/TRAC)" are displayed on the intelligent tester C



A

2.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU CAN BRANCH WIRE)

B

3.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU CAN BRANCH WIRE)

C

4.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU)
2.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
a.
U148256E01
0.118,0.031 0.316,0.229 0.198,0.198 10 *a 1.683,0.083 1.969,0.269 0.286,0.186 10 A6 0.218,1.676 0.658,1.822 0.440,0.147 10 CANL 0.408,1.871 0.848,2.040 0.440,0.169 10 CANH 1.315,1.343 1.042,1.944 1.042,1.944 0.936,1.944 false 1.315,1.217 0.8,1.754 0.8,1.754 0.722,1.754 false

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A6-25 (CANH) - A6-14 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU)

3.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
a.
U115863E01
0.073,0.08 0.270,0.266 0.197,0.186 10 *a 1.595,0.663 1.881,0.849 0.286,0.186 10 A7 2.493,0.813 2.933,0.999 0.440,0.186 10 CANH 2.864,1.077 3.262,1.246 0.398,0.169 10 CANL 2.207,1.77 2.36,0.902 2.36,0.902 2.465,0.902 false 2.207,1.896 2.765,1.162 2.765,1.162 2.843,1.162 false

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A7-11 (CANH) - A7-25 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])



OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU)

4.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU)
a.

Disconnect the G64 main body ECU (multiplex network body ECU) connector.


b.

Select "Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Main Body" is not displayed on the intelligent tester A
Several ECUs and sensors in addition to "Main Body" are displayed on the intelligent tester B



A

5.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU CAN BRANCH WIRE)

B

6.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY)
5.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU CAN BRANCH WIRE)
a.
U148349E04
1.271,0.469 1.365,0.469 1.365,0.469 1.604,1.188 true 1.531,1.198 1.042,0.719 1.042,0.719 0.958,0.719 true 0.052,0 0.292,0.188 0.24,0.188 10 false *a 0.542,0.635 0.969,0.792 0.427,0.156 10 false CANH 0.896,0.396 1.302,0.552 0.406,0.156 10 false CANL 0.458,1.125 0.792,1.281 0.333,0.156 10 false G64

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G64-14 (CANH) - G64-13 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (MAIN BODY ECU)

6.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the G1 center airbag sensor assembly connector.


b.

Select "Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Airbag" is not displayed on the intelligent tester A
Several ECUs and sensors in addition to "Airbag" are displayed on the intelligent tester B



A

7.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)

B

8.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR)
7.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
U148246E01
0.041,0 0.230,0.177 0.189,0.177 10 *a 0.132,1.336 0.551,1.513 0.419,0.177 10 CANH 0.295,0.987 0.560,1.164 0.266,0.177 10 G1 0.312,1.769 0.732,1.946 0.419,0.177 10 CANL 1.279,1.077 0.725,1.419 0.725,1.419 0.652,1.419 false 1.176,1.487 0.95,1.863 0.95,1.863 0.823,1.863 false

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G1-13 (CANH) - G1-22 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Center Airbag Sensor Assembly)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY)

8.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR)
NOTICE:

For vehicles without a vehicle stability control system (for hydraulic brake booster), go to "Check for Open in One Side of CAN Branch Wire (Radio and Display Receiver Assembly)".


a.

Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.


b.

Select "Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Spiral cable (Steering Angle Sensor)" is not displayed on the intelligent tester A
Several ECUs and sensors in addition to "Spiral cable (Steering Angle Sensor)" are displayed on the intelligent tester B



A

9.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)

B

10.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)
9.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
a.
U148232E05
2.031,1.552 1.708,1.156 1.708,1.156 1.635,1.156 true 2.146,1.552 2.396,1.292 2.396,1.292 2.479,1.292 true 1.219,1.063 1.646,1.26 0.427,0.198 10 false CANH 0.896,1.448 1.219,1.646 0.323,0.198 10 false G33 0.083,0 0.51,0.198 0.427,0.198 10 false *a 2.51,1.208 2.927,1.406 0.417,0.198 10 false CANL

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G33-4 (CANH) - G33-3 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor])



OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR)

10.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)
NOTICE:

For vehicles without an audio and visual system (for radio and display type), go to "Check for Open in One Side of CAN Branch Wire (Four Wheel Drive Control ECU)".


a.

Disconnect the H51 radio and display receiver assembly connector.


b.

Select "Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Display and Navigation (AVN1)" is not displayed on the intelligent tester A
Several ECUs and sensors in addition to "Display and Navigation (AVN1)" are displayed on the intelligent tester B



A

11.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE)

B

12.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (FOUR WHEEL DRIVE CONTROL ECU)
11.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE)
a.
U148880E01
0.082,0.083 0.286,0.253 0.205,0.170 10 *a 1.58,0.371 1.854,0.512 0.274,0.140 10 H51 2.039,1.299 2.26,1.774 2.26,1.774 2.366,1.774 false 1.908,1.299 1.687,1.774 1.687,1.774 1.581,1.774 false 1.079,1.699 1.490,1.837 0.411,0.139 10 CANH 2.398,1.699 2.809,1.837 0.411,0.139 10 CANL

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H51-9 (CANH) - H51-10 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY)

12.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (FOUR WHEEL DRIVE CONTROL ECU)
a.

Disconnect the G53 four wheel drive control ECU connector.


b.

Select "Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Four Wheel Drive Control" is not displayed on the intelligent tester A
Several ECUs and sensors in addition to "Four Wheel Drive Control" are displayed on the intelligent tester B



A

13.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (FOUR WHEEL DRIVE CONTROL ECU CAN BRANCH WIRE)

B

14.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
13.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (FOUR WHEEL DRIVE CONTROL ECU CAN BRANCH WIRE)
a.
U148351E03
0.49,1.01 0.573,1.01 0.573,1.01 0.688,1.344 false 0.594,0.719 0.688,0.719 0.688,0.719 0.76,1.365 false 0.052,0 0.219,0.188 0.167,0.188 10 false *a 0.167,0.635 0.594,0.792 0.427,0.156 10 false CANH 0.094,0.927 0.49,1.083 0.396,0.156 10 false CANL 2.417,1.229 2.719,1.385 0.302,0.156 10 false G53

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G53-19 (CANH) - G53-20 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Four Wheel Drive Control ECU)



OK

REPLACE FOUR WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU)

14.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the G25 air conditioning amplifier assembly connector.


b.

Select "Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Air Conditioning Amplifier" is not displayed on the intelligent tester A
Several ECUs and sensors in addition to "Air Conditioning Amplifier" are displayed on the intelligent tester B



A

15.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)

B

16.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY)
15.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)
a.
U170009E02
2.104,1.083 1.927,0.146 1.927,0.146 1.792,0.146 false 2.021,1.115 1.198,0.323 1.198,0.323 1.073,0.323 false 0.052,0 0.229,0.208 0.177,0.208 10 false *a 0.292,0.917 0.604,1.094 0.313,0.177 10 false G25 1.344,0.063 1.781,0.229 0.438,0.167 10 false CANH 0.688,0.24 1.094,0.417 0.406,0.177 10 false CANL

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G25-11 (CANH) - G25-12 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY)

16.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY)
NOTICE:

For vehicles with a 5L-E engine, go to "Check for Open in One Side of CAN Branch Wire (Network Gateway ECU)".


a.

Disconnect the G46 power steering ECU assembly connector.


b.

Select "Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"PPS" is not displayed on the intelligent tester A
Several ECUs and sensors in addition to "PPS" are displayed on the intelligent tester B



A

17.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE)

B

18.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NETWORK GATEWAY ECU)
17.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE)
a.
U148346E03
1.917,1.521 2.135,1.063 2.135,1.063 2.229,1.063 false 2.354,1.25 2.281,1.25 2.281,1.25 2.01,1.521 false 0.063,0 0.333,0.229 0.271,0.229 10 false *a 2.396,1.167 2.823,1.333 0.427,0.167 10 false CANH 2.26,0.979 2.677,1.146 0.417,0.167 10 false CANL 0.625,1.365 0.948,1.531 0.323,0.167 10 false G46

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G46-1 (CANH) - G46-2 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (POWER STEERING ECU ASSEMBLY)

18.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NETWORK GATEWAY ECU)
NOTICE:

For vehicles without a TOYOTA parking assist-sensor system (for 4 sensor type), go to "Check for Open in One Side of CAN Branch Wire (Yaw Rate Sensor Assembly CAN Branch Wire)".


a.

Disconnect the G155 network gateway ECU connector.


b.

Select "Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"CAN Gateway1" is not displayed on the intelligent tester A
Several ECUs and sensors in addition to "CAN Gateway1" are displayed on the intelligent tester B



A

19.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NETWORK GATEWAY ECU CAN BRANCH WIRE)

B

20.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR ASSEMBLY CAN BRANCH WIRE)
19.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NETWORK GATEWAY ECU CAN BRANCH WIRE)
a.
U170303E01
2.704,1.13 3.061,1.267 0.358,0.137 10 G155 1.249,1.278 1.064,1.49 1.064,1.49 0.941,1.49 false 1.162,1.765 1.285,1.765 1.285,1.765 1.358,1.276 false 0.451,1.415 0.840,1.552 0.389,0.137 10 CA1H 0.713,1.679 1.102,1.816 0.389,0.137 10 CA1L 0.07,0.056 0.371,0.193 0.301,0.137 10 *a

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G155-16 (CA1H) - G155-15 (CA1L) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (NETWORK GATEWAY ECU)

20.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
U148302E04
0.917,1.021 1.01,1.021 1.01,1.021 1.438,1.479 false 1.167,0.573 1.281,0.573 1.281,0.573 1.563,1.469 false 0.052,0 0.229,0.177 0.177,0.177 10 false *a 0.521,0.927 0.927,1.104 0.406,0.177 10 false CANL 0.427,1.448 0.729,1.625 0.302,0.177 10 false G52 0.75,0.49 1.177,0.667 0.427,0.177 10 false CANH

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Disconnect the G52 yaw rate sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G52-3 (CANH) - G52-2 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (YAW RATE SENSOR ASSEMBLY)