Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › ENGINE UNIT › from 2020.08
RM27T0E _51 Engine / Hybrid System _053665 1GD-FTV ENGINE MECHANICAL _0260522 ENGINE UNIT A

1GD-FTV ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 12633 1.REMOVE NO. 3 ENGINE COVER BRACKET (w/o Urea SCR System)

Hide 12632 2.REMOVE NO. 2 ENGINE COVER BRACKET (w/o Urea SCR System)

Hide 82121 3.REMOVE ENGINE WIRE

Hide 77246C 4.REMOVE FUEL MAIN TUBE SUPPORT

Hide 26100G 5.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 16278 6.REMOVE NO. 2 WATER BY-PASS PIPE

Hide 89481B 7.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ DPF)

Hide 89425 8.REMOVE EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)

Hide 25625 15.REMOVE EGR VALVE BRACKET (w/ EGR System)

Hide 25612 16.REMOVE NO. 2 EGR PIPE (w/ EGR System)

Hide 16206B 17.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/ EGR Cooler)

Hide 16206B 18.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/o EGR Cooler)

a.
A368227

Disconnect the No. 4 fuel hose from the No. 3 water by-pass pipe sub-assembly.


b.
A398419C01
0.083,0.104 0.323,0.281 0.24,0.177 10 true *A 0.115,2.667 0.344,2.844 0.229,0.177 10 true *B
*A w/ EGR System
*B w/o EGR System


w/ EGR System:

Slide the clamp and disconnect the No. 8 water by-pass hose from the No. 3 water by-pass pipe sub-assembly.


c.

Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly from the EGR valve adapter sub-assembly.


Hide 25601 19.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

a.
A428763C01
0.094,0.135 0.406,0.292 0.313,0.156 10 false *A 0.115,2.552 0.427,2.708 0.313,0.156 10 false *B
*A w/o EGR Pre-cooler
*B w/ EGR Pre-cooler


Remove the 4 nuts, bolt and No. 1 EGR pipe sub-assembly from the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.


b.

Remove the 2 gaskets from the exhaust manifold and electric EGR control valve assembly.


c.
A354081

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


Hide 25804 20.REMOVE VACUUM CONTROL VALVE SET (w/ EGR Cooler)

Hide 16209 21.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A354082C01
0.969,0.24 1.177,0.24 1.177,0.24 1.74,0.781 true 0.781,2 0.99,2 0.99,2 1.396,1.583 true 3.031,2.063 2.802,2.063 2.802,2.063 2.802,1.781 true 2.167,0.125 2.354,0.125 2.354,0.125 2.698,0.458 true 2.188,2.594 2.375,2.594 2.375,2.594 2.635,3.021 true 1.042,3.333 1.74,3.333 true 3.052,3.667 2.823,3.667 2.823,3.667 2.823,4.167 true 0.104,0.063 0.469,0.313 0.365,0.25 12 false *A 0.104,2.49 0.5,2.74 0.396,0.25 12 false *B 3.073,3.573 3.333,3.792 0.26,0.219 10 true *1 0.802,0.135 1.042,0.333 0.24,0.198 10 true *2 1.969,0.031 2.177,0.229 0.208,0.198 10 true *3 0.625,1.906 0.938,2.063 0.313,0.156 10 false *4 3.063,1.979 3.313,2.198 0.25,0.219 10 true *1 2.01,2.5 2.271,2.719 0.26,0.219 10 true *3 0.865,3.24 1.104,3.438 0.24,0.198 10 true *2
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles
*1 No. 6 Water By-pass Hose
*2 No. 7 Water By-pass Hose
*3 Water Hose
*4 No. 11 Water By-pass Hose


w/o EGR Pre-cooler:

i.

Slide the clamp and disconnect the No. 6 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


ii.

Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


iii.

Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.


iv.

for Cold Area Specification Vehicles:

Detach the clamp and disconnect the No. 11 water by-pass hose from the No. 2 fuel pipe.


v.

Remove the 2 bolts and No. 4 water by-pass pipe sub-assembly from the intake manifold.



b.
A347295C01
0.833,0.229 1.021,0.229 1.021,0.229 1.708,0.76 true 2.25,0.208 2.448,0.208 2.448,0.208 2.677,0.5 true 2.958,0.833 2.74,0.833 2.74,0.833 2.74,1.167 true 0.708,2.073 0.906,2.073 0.906,2.073 1.333,1.635 true 2.302,2.646 2.5,2.646 2.5,2.646 2.729,2.938 true 2.125,2.135 2.302,2.135 2.302,2.135 2.635,1.865 true 2.958,3.271 2.74,3.271 2.74,3.271 2.74,3.604 true 2.188,4.49 2.365,4.49 2.365,4.49 2.698,4.219 true 0.927,2.729 1.115,2.729 1.115,2.729 1.792,3.25 true 0.073,0.052 0.438,0.375 0.365,0.323 12 true *A 0.073,2.51 0.396,2.802 0.323,0.292 12 true *B 1.948,2.042 2.135,2.229 0.188,0.188 10 true *1 0.656,0.135 0.875,0.344 0.219,0.208 10 false *2 2.063,0.104 2.271,0.292 0.208,0.188 10 true *3 0.531,1.969 0.781,2.177 0.25,0.208 10 false *4 2.99,0.74 3.24,0.948 0.25,0.208 10 true *5 2.01,4.396 2.208,4.594 0.198,0.198 10 true *1 2.104,2.552 2.302,2.75 0.198,0.198 10 true *3 0.75,2.635 0.969,2.844 0.219,0.208 10 false *2 2.979,3.177 3.198,3.354 0.219,0.177 10 true *5
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles
*1 No. 6 Water By-pass Hose
*2 No. 7 Water By-pass Hose
*3 Water Hose
*4 No. 11 Water By-pass Hose
*5 No. 17 Water By-pass Hose


w/ EGR Pre-cooler:

i.

Slide the clamp and disconnect the No. 6 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


ii.

Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


iii.

Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.


iv.

Slide the clamp and disconnect the No. 17 water by-pass hose from the EGR pipe with cooler sub-assembly.


v.

for Cold Area Specification Vehicles:

Detach the clamp and disconnect the No. 11 water by-pass hose from the No. 2 fuel pipe.


vi.

Remove the 2 bolts and No. 4 water by-pass pipe sub-assembly from the intake manifold.



Hide 25800 22.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR Cooler)

Hide 23.REMOVE EGR VALVE ADAPTER SUB-ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System without EGR Cooler)

a.
A365517

Remove the 4 bolts and EGR valve adapter sub-assembly with electric EGR control valve assembly from the intake manifold.


Hide 25624 24.REMOVE EGR VALVE ADAPTER SUB-ASSEMBLY (w/o EGR System)

a.
A398418

Remove the 4 bolts and EGR valve adapter sub-assembly from the intake manifold.


Hide 25617 25.REMOVE EGR HOLE COVER PLATE (w/o EGR System)

a.
A398420

Remove the 4 nuts and 2 EGR cooler hole plates and 2 gaskets from the intake manifold and exhaust manifold.


b.
A352178

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


Hide 11409 26.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 23812D 27.REMOVE NO. 2 FUEL PIPE

a.
A343499

Slide the clamp and disconnect the No. 1 fuel hose from the No. 2 fuel pipe.


b.

Remove the bolt and No. 2 fuel pipe from the manifold stay.


Hide 28.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 22803 30.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 23243B 31.REMOVE FUEL PUMP MOTOR WIRE

Hide 23273H 32.REMOVE NO. 2 FUEL HOSE

Hide 23271H 33.REMOVE NO. 1 FUEL HOSE

Hide 23804D 34.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)

Hide 23804D 35.REMOVE NO. 4 FUEL PIPE (w/o DPF)

Hide 23804C 37.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

Hide 23770 38.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 40.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 42.REMOVE WIRING HARNESS CLAMP BRACKET

a.
A354083

for LHD:

Remove the 3 bolts and 3 wiring harness clamp brackets from the cylinder head cover sub-assembly.


b.
A421445

for RHD:

Remove the 2 bolts and 2 wiring harness clamp brackets from the cylinder head cover sub-assembly.


Hide 23701 43.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23810A 44.REMOVE COMMON RAIL ASSEMBLY

Hide 19871 45.REMOVE NO. 1 GLOW PLUG CONNECTOR

Hide 19850 46.REMOVE GLOW PLUG ASSEMBLY

Hide 47.REMOVE HOSE BRACKET

a.
A343501

Remove the 2 bolts and hose bracket from the cylinder head sub-assembly.


Hide 23300 49.REMOVE FUEL FILTER ASSEMBLY

a.
A347297

Remove the 2 nuts and fuel filter assembly from the cylinder block sub-assembly.


Hide 16025 50.REMOVE NO. 5 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A343503

Remove the 3 bolts, No. 5 water by-pass pipe sub-assembly and gasket from the cylinder block sub-assembly.


Hide 88431 51.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

a.
A354085

Remove the 4 bolts and No. 1 compressor mounting bracket from the cylinder block sub-assembly, timing chain case assembly and timing chain cover sub-assembly.


Hide 89422C 52.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 12261 53.REMOVE PCV HOSE (except Cold Area Specification Vehicles)

Hide 12229 54.REMOVE PCV PIPE (for Cold Area Specification Vehicles)

Hide 55.REMOVE WATER BY-PASS HOSE (w/ Urea SCR System)

Hide 16282 56.REMOVE NO. 5 WATER BY-PASS HOSE (w/ DPF)

a.
A347299

Slide the 2 clamps and disconnect the No. 5 water by-pass hose from the No. 1 injector holder and water outlet sub-assembly.


b.

Detach the clamp and remove the No. 5 water by-pass hose from the No. 1 water hose clamp bracket.


Hide 16281 57.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)

a.
A347300

Slide the clamp and disconnect the No. 4 water by-pass hose from the No. 1 injector holder.


Hide 23295D 58.REMOVE NO. 1 INJECTOR HOLDER (w/ DPF)

Hide 17168 59.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)

Hide 89467B 60.REMOVE AIR FUEL RATIO SENSOR (w/ DPF)

Hide 17167 61.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)

Hide 17167 62.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/o DPF)


b.
A407040

w/o EGR Cooler:

Remove the 3 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.


Hide 17271 63.REMOVE NO. 1 TURBO INSULATOR (w/ DPF)

Hide 17271 64.REMOVE NO. 1 TURBO INSULATOR (w/o DPF)


b.
A407041

w/o EGR Cooler:

Remove the 3 bolts and No. 1 turbo insulator from the turbine outlet elbow and turbocharger sub-assembly.


Hide 89463C 65.DISCONNECT NO. 1 NITROGEN OXIDES SENSOR (w/ Urea SCR System)

Hide 66.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY (w/ DPF)

Hide 67.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY (w/o DPF)


b.
A407042

w/o EGR Cooler:

Remove the bolt, 2 nuts and No. 2 exhaust pipe support stay from the cylinder block sub-assembly and turbine outlet elbow.


Hide 69.REMOVE EXHAUST PIPE SUPPORT STAY (w/o DPF)


b.
A407043

w/o EGR Cooler:

Remove the 3 bolts and exhaust pipe support stay from the cylinder block sub-assembly and turbine outlet elbow.


Hide 25051 70.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/ EGR Cooler)

Hide 17291 71.REMOVE TURBINE OUTLET ELBOW (w/o EGR Cooler)

a.
A407025

Remove the nut, exhaust pipe clamp and turbine outlet elbow from the turbocharger sub-assembly.


b.

Remove the gasket.


Hide 89463C 72.REMOVE NO. 1 NITROGEN OXIDES SENSOR (w/ Urea SCR System)

Hide 12361 73.REMOVE FRONT ENGINE MOUNTING INSULATOR RH

a.
A354086

Disconnect the No. 3 vacuum transmitting hose sub-assembly from the front engine mounting insulator RH.


b.

Remove the nut and front engine mounting insulator RH from the front No. 1 engine mounting bracket RH.


Hide 16268 75.REMOVE NO. 1 WATER BY-PASS PIPE

a.

Remove the 3 bolts, No. 1 water by-pass pipe and gasket from the timing chain cover sub-assembly.

A428764C03
0.073,0.052 4.906,1.75 4.833,1.698 0.427,0.104 2.479,1.698 2.052,1.594 2.823,0.104 4.875,1.698 2.052,1.594 0.146,0.094 0.458,0.25 0.313,0.156 10 false *A 5,0.083 5.313,0.24 0.313,0.156 10 false *B 0.5,0.156 0.813,0.313 0.313,0.156 10 false *C 2.875,0.146 3.188,0.302 0.313,0.156 10 false *D
*A w/o Urea SCR System *B w/ Urea SCR System
*C except Cold Area Specification Vehicles *D for Cold Area Specification Vehicles



Hide 16284 76.DISCONNECT NO. 1 AND NO. 2 TURBO WATER HOSE

Hide 87101 77.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)

a.
A354088

Remove the 4 bolts and No. 1 viscous heater bracket sub-assembly from the cylinder block sub-assembly and timing chain cover sub-assembly.


Hide 15407 80.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 83530 83.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY (w/o 2 Stage Hydraulic Switching Oil Pump System)

Hide 83520 84.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY (w/ 2 Stage Hydraulic Switching Oil Pump System)

Hide 15350 85.REMOVE OIL PRESSURE SWITCHING VALVE ASSEMBLY (w/ 2 Stage Hydraulic Switching Oil Pump System)

Hide 16207 86.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A343506

Slide the clamp and disconnect the No. 3 water by-pass hose from the water outlet sub-assembly.


b.

Remove the 2 bolts and No. 2 water by-pass pipe sub-assembly from the engine water pump assembly and water inlet.


Hide 16304 87.REMOVE WATER OUTLET SUB-ASSEMBLY

a.
A347303E01
0.048,0.035 0.310,0.211 0.262,0.176 12 *A 0.048,2.436 0.308,2.613 0.259,0.176 12 *B

Remove the 4 bolts, 2 nuts and water outlet sub-assembly from the timing chain cover sub-assembly.

Text in Illustration
*A w/ DPF
*B w/o DPF


b.

Remove the gasket from the timing chain cover sub-assembly.


Hide 16603 88.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16620 89.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 25804A 90.REMOVE VACUUM SWITCHING VALVE SUB-ASSEMBLY (for Engine Mounting)

Hide 25706 91.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A456453

Disconnect the No. 1 vacuum transmitting hose sub-assembly from the vacuum pump assembly.


b.
A457925

Disconnect the No. 2 vacuum transmitting hose sub-assembly from the No. 3 vacuum transmitting pipe sub-assembly.


c.

Remove the 3 bolts and No. 1 vacuum transmitting pipe sub-assembly from the cylinder head sub-assembly.


Hide 25707 92.REMOVE NO. 2 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A354091

Remove the 2 bolts and No. 2 vacuum transmitting pipe sub-assembly from the cylinder block sub-assembly and oil pan sub-assembly.


Hide 25708 93.REMOVE NO. 3 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A428765C01
0.115,0.146 0.427,0.302 0.313,0.156 10 false *A 0.135,2.49 0.448,2.646 0.313,0.156 10 false *B
*A w/o Urea SCR System
*B w/ Urea SCR System


Disconnect the No. 4 vacuum transmitting hose sub-assembly from the No. 3 vacuum transmitting pipe sub-assembly.


b.

Remove the 2 bolts and No. 3 vacuum transmitting pipe sub-assembly from the cylinder head sub-assembly and cylinder block sub-assembly.


Hide 25709E 94.REMOVE NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A354093

Remove the bolt and No. 4 vacuum transmitting pipe sub-assembly from the cylinder block sub-assembly.


Hide 88451B 95.REMOVE VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)

Hide 16575C 98.REMOVE NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)

a.
A347304

Remove the bolt and No. 1 water hose clamp bracket from the timing chain case assembly.