Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM J

1GD-FTV ENGINE CONTROL  ECD SYSTEM  Engine Knocking or Rattling  


DESCRIPTION

Malfunction Condition Main Trouble Area Related Trouble Area
·

Knocking and abnormal sound due to extremely rich combustion

·

Abnormal sound due to friction between parts


(a) Injector assembly malfunctions
·

Injector sliding malfunction

·

Injector stuck closed

·

Injector stuck open

·

Deposits in injector

·

Injector circuit malfunction


(b) Abnormal common rail pressure
·

Pre-stroke control valve

·

Fuel pulsation sound

·

Air in fuel


(c) Friction between parts
(d) Compression pressure
·

Fuel leakage

·

Intake system leakage

·

Intake system blockage

·

EGR system

·

Throttle valve system

·

Fuel pressure sensor (built into injector assembly)

·

Manifold absolute pressure sensor

·

Mass air flow meter sub-assembly

·

Atmospheric pressure sensor (built into ECM)

·

Vehicle modifications

·

Low quality fuel

·

Lack of fuel

·

ECM



HINT:
·

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors of the malfunction.

·

Check that the vehicle has not been modified in any way prior to the vehicle inspection.



CAUTION / NOTICE / HINT

HINT:
·

This troubleshooting procedure checks for knocking and rattling.

·

Knocking is most likely to occur while the engine is idling.



NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK SOUND AREA
a.

Find the source of the abnormal sound using a mechanic's sound scope.

Result:
Result Proceed to
Combustion noise from engine A
Noise from specific part B




A

2.READ OUTPUT DTCS (RELATING TO ENGINE)

B

REPAIR OR REPLACE MALFUNCTIONING PARTS

2.READ OUTPUT DTCS (RELATING TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Result:
Result Proceed to
No DTC is output A
Engine related DTCs are output B




A

3.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (AFTER ENGINE WARMED UP) (PROCEDURE 3)

B

3.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (AFTER ENGINE WARMED UP) (PROCEDURE 3)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Diesel Knocking.


d.

Take a snapshot of the following Data List items.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.

·

Check the Data List at idling and at 4000 rpm with no load after the engine is warmed up.




Result:
Proceed to
NEXT



NEXT

4.CHECK SNAPSHOT (INJECTION FEEDBACK VALUE #1 TO #4 AND TARGET INJECTION VOLUME)
4.CHECK SNAPSHOT (INJECTION FEEDBACK VALUE #1 TO #4 AND TARGET INJECTION VOLUME)
a.

Check Injection Feedback Value #1 to #4 and Target Injection Volume in the snapshot taken in procedure 3 when the engine was idling and at 4000 rpm with no load.

Result:
Result Proceed to
Injection Feedback Value for at least one cylinder is more than +5 mm3/st A
Target Injection Volume is less than 12.0 mm3/st at 4000 rpm B
Except above C


HINT:
·

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Value to increase.

·

The ECM controls the system so that the sum of Injection Feedback Value for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Value for a cylinder is less than -5.0 mm3/st (-5.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Value for each of the other cylinders is 5.0 mm3/st or less, the injector assemblies are not malfunctioning.





A

5.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)

B

12.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

C

13.CHECK SNAPSHOT (TARGET FUEL PRESSURE (HIGH) AND FUEL PRESSURE (HIGH))
5.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed Cylinder #1 to #4.


d.

Check the engine speed during the Active Test.

Result:
Result Proceed to
Except below A
The values of Engine Speed Cylinder #1 to #4 are within 10 rpm of each other B


HINT:

When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.




A

6.CHECK CYLINDER COMPRESSION PRESSURE

B

7.CHECK SNAPSHOT (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEANING STATUS HISTORY #1 TO #4)
6.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION

HINT:

When compression is low, there may be cracks in the piston or the injector may be installed improperly.



Result:
Proceed to
OK
NG



OK

7.CHECK SNAPSHOT (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEANING STATUS HISTORY #1 TO #4)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

7.CHECK SNAPSHOT (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEANING STATUS HISTORY #1 TO #4)
a.

Check Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4 in the snapshot taken in procedure 3 when the engine was idling and at 4000 rpm.


b.

Record the value displayed for Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4.


Result:
Proceed to
NEXT



NEXT

8.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
8.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
NOTICE:
·

Replace the injector assembly of the cylinder which displays a value of 5.0 mm3/st or higher for Injection Feedback Value #1 to #4 in step 4 or 17.

·

Only replace the injector assembly for the cylinder which displays an Injector Leaking Count #1 to #4 value of 1 or more, or i-ART Learning Status History #1 to #4 value of 1 Trip or more.

·

If Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4 both display 0, only replace the injector assembly for the cylinder which was determined to be malfunctioning using Injection Feedback Value #1 to #4.



a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

9.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
9.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT

HINT:

Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

10.BLEED AIR FROM FUEL SYSTEM
10.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the knocking has been successfully repaired.


Result:
Proceed to
NEXT



NEXT

END

12.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies of all cylinders.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

9.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
13.CHECK SNAPSHOT (TARGET FUEL PRESSURE (HIGH) AND FUEL PRESSURE (HIGH))
a.

Check Fuel Pressure (High) and Target Fuel Pressure (High) in the snapshot taken in procedure 3 when the engine was warmed up and idling.

OK:

Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High).



Result:
Proceed to
OK
NG



OK

14.CHECK THE TEMPERATURE WHEN KNOCKING OCCURS

NG

22.REPLACE FUEL SUPPLY PUMP ASSEMBLY
14.CHECK THE TEMPERATURE WHEN KNOCKING OCCURS
a.

Check the temperature when knocking trouble occurs.

Result:
Result Proceed to
Knocking occurs only in cold engine A
Knocking occurs both in cold and warmed up engine B




A

15.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

B

18.CHECK SNAPSHOT (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEARNING STATUS HISTORY #1 TO #4)
15.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

Result:
Proceed to
OK
NG



OK

16.TAKE SNAPSHOT DURING IDLING (WHEN ENGINE COLD)

NG

16.TAKE SNAPSHOT DURING IDLING (WHEN ENGINE COLD)
a.

Make sure that the engine is cold so that the snapshot can be taken under the correct conditions.


b.

Connect the GTS to the DLC3.


c.

Start the engine and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Diesel Knocking.


e.

Take a snapshot of the following Data List items.

HINT:

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.



Result:
Proceed to
NEXT



NEXT

17.CHECK SNAPSHOT (INJECTION FEEDBACK VALUE #1 TO #4)
17.CHECK SNAPSHOT (INJECTION FEEDBACK VALUE #1 TO #4)
a.

Check Injection Feedback Value #1 to #4 in the snapshot taken in procedure 3 when the engine was idling.

Result:
Result Proceed to
Injection Feedback Value for at least one cylinder is more than +5 mm3/st A
Except above B


HINT:
·

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Value to increase.

·

The ECM controls the system so that the sum of Injection Feedback Value for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Value for a cylinder is less than -5.0 mm3/st (-5.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Value for each of the other cylinders is 5.0 mm3/st or less, the injector assemblies are not malfunctioning.





A

7.CHECK SNAPSHOT (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEANING STATUS HISTORY #1 TO #4)

B

18.CHECK SNAPSHOT (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEARNING STATUS HISTORY #1 TO #4)
18.CHECK SNAPSHOT (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEARNING STATUS HISTORY #1 TO #4)
a.

Check Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4 in the snapshot taken in procedure 3 when the engine was idling and at 4000 rpm.

Result:
Result Proceed to
The value for Injector Leaking Count #1 to #4 does not change from 0
The value for i-ART Learning Status History #1 to #4 does not change from 0 Trip
A
The value for Injector Leaking Count #1 to #4 displays 1 or more
The value for i-ART Learning Status History #1 to #4 displays 1 Trip or more
B




A

19.READ VALUE USING GTS (ATMOSPHERIC PRESSURE AND INTAKE MANIFOLD ABSOLUTE PRESSURE)

B

21.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
19.READ VALUE USING GTS (ATMOSPHERIC PRESSURE AND INTAKE MANIFOLD ABSOLUTE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Atmospheric Pressure and Intake Manifold Absolute Pressure.


d.

Compare Intake Manifold Absolute Pressure to Atmospheric Pressure when the ignition switch is ON (do not start the engine).

Standard:

Difference between Intake Manifold Absolute Pressure and Atmospheric Pressure is less than 8 kPa.


HINT:
·

If Intake Manifold Absolute Pressure and Atmospheric Pressure have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.

·

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.



Result:
Result Proceed to
Intake Manifold Absolute Pressure and Atmospheric Pressure have same value A
Intake Manifold Absolute Pressure is different from actual atmospheric pressure B
Atmospheric Pressure is different from actual atmospheric pressure C




A

20.BASIC INSPECTION

B

C

20.BASIC INSPECTION
a.

Check the fuel quality.


b.

Check the fuel for air.


c.

Check the fuel system for blockages.


d.

Check the air cleaner filter element sub-assembly.


e.

Check the engine oil.


f.

Check the engine coolant.


g.

Check the engine idling speed and maximum engine speed.


h.

Check the vacuum pump.


Result:
Proceed to
NEXT



NEXT

END

21.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
NOTICE:

Only replace the injector assembly for the cylinder which displays an Injector Leaking Count #1 to #4 value of 1 or more, or i-ART Learning Status History #1 to #4 value of 1 Trip or more.


a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

9.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
22.REPLACE FUEL SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL

HINT:

If the common rail pressure becomes too high when transitioning due to problems with pre-stroke control valve operation, knocking noise worsens.

When the common rail pressure becomes excessively high as a result of a pre-stroke control valve malfunction, knocking sounds worsen.



Result:
Proceed to
NEXT



NEXT

23.BLEED AIR FROM FUEL SYSTEM
23.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

24.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
24.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the knocking has been successfully repaired by starting the engine.


Result:
Proceed to
NEXT



NEXT

END