Faults and Symptoms of Common Rail Diesel Components
Engine Control
| Main fault | Decrease in performance (foreign matter is stuck) |
| Symptoms | Lack of power, black smoke |
| Data List | Mass Air Flow Sensor |
|
|
| Symptom and Corresponding Main Fault | ·
Lack of power (no black smoke) due to air cleaner filter element blockage or crushed or leaking air duct ·
Black smoke (no lack of power) due to leakage between the turbocharger and intake manifold |
| Data List | Intake Manifold Absolute Pressure |
| Main fault | ·
Air leak in the turbocharged air passage ·
ECM not operating well ·
Turbocharger (turbine, bearing) |
| Symptoms | Lack of power (when vehicle is starting, under heavy load)
(Black smoke is not emitted when racing while vehicle is stopped) |
| Data List | Intake Manifold Absolute Pressure
·
With the engine switch on (IG) or during idling, Intake Manifold Absolute Pressure = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and Intake Manifold Absolute Pressure becomes higher than atmospheric pressure. ·
Atmospheric pressure decreases by 1 kPa each time elevation increases by 100 m, and is also affected by the current weather conditions. |
| Main fault | Blockage |
| Symptoms | Lack of power (high engine speed, under heavy load) |
| Main fault | Glow system malfunction |
| Symptoms | Difficult to start, rough idle, knocking, white smoke (when cold) |
| Diagnostic Point | ·
Measure the resistance of the glow plug assembly ·
Check the glow plug indicator light |
| Main fault | Battery is depleted |
| Symptoms | Difficult to start (cannot crank, crank speed is low), horn is quiet |
| Data List | Battery Voltage
·
When cranking, battery voltage is below 5 V. |
| Main fault | Damaged, seized up |
| Symptoms | Cannot crank, crank speed is low, strange noise |
| Main fault | Loss of compression |
| Symptoms | Rough idle (lack of power always) |
| Data List | Engine Speed Cylinder
·
When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression. Injection Feedback Value ·
When an Injector Feedback Val is more than 5 mm3/st, there may be a malfunction in the corresponding cylinder. |
| Main fault | Starter system malfunction |
| Symptoms | Difficult to start |
| Data List | Starter SW
·
Engine switch (STA) output: ON: Starter is operating OFF: Starter is not operating |
Diesel Injection
| Main fault | - |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power |
| Data List | Fuel Pressure (High), Target Fuel Pressure (High)
·
Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High) during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)). ·
If the fuel pressure is 20000 kPag below the target pressure, then a lack of power will be felt. ·
If the fuel pressure is below 25000 kPag, then idling will be rough.
|
| Diagnostic Trouble Code | Even if Fuel Pressure (High) is below Target Fuel Pressure (High), a DTC will not be stored. |
| Main fault | Blockage |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power |
| Data List | Fuel Pressure (High), Target Fuel Pressure (High)
·
Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High) during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)). ·
If the fuel pressure is 20000 kPag below the target pressure, then a lack of power will be felt. ·
If the fuel pressure is below 25000 kPag, then idling will be rough.
|
| Diagnostic Trouble Code | Even if Fuel Pressure (High) is below Target Fuel Pressure (High), a DTC will not be stored. |
| Main fault | Blockage |
| Symptoms | Rough idle, lack of power, black smoke, white smoke, knocking |
| Data List | Injection Feedback Value
·
When an Injector Feedback Value is more than 5 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute. |
| Main fault | Does not completely close |
| Symptoms | Difficult to start, engine stall, rough idle, lack of power |
| Main fault | Open circuit, decrease in performance (foreign matter is stuck) |
| Symptoms | Difficult to start, rough idle, engine stall, lack of power |
| Data List | Fuel Pressure (High), Target Fuel Pressure (High)
·
Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Fuel Pressure (High) follows Target Fuel Pressure (High). If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (either Fuel Pressure (High) decreases to a value less than Target Fuel Pressure (High)). |
| Diagnostic Trouble Code | When the fuel pressure sensor has a fault, some DTCs may be stored. |
| Main fault | - |
| Symptoms | Difficult to start, rough idle (especially when cold) |
Diesel EGR
| Main fault | ·
Does not move smoothly ·
Does not close completely |
| Symptoms | ·
Rough idle ·
EGR valve stuck closed: A loud turbocharger sound. ·
EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt). |
| Data List | Actual EGR Valve Position No.1, Target EGR Valve Position No.1
·
Generally, Actual EGR Valve Position No.1. = Target EGR Position +/-5% (fully closed: 0%, fully open: 100%). ·
Using the EGR valve Active Test, check whether Actual EGR Valve Position No.1. follows Target EGR Valve Position No.1 (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs). ·
EGR valve is fully closed when the engine switch is turned on (IG) (engine stopped). ·
EGR valve opens to the halfway point at idling after the engine is warmed up. EGR Close Learning Value Bank 1 ·
When leaving the vehicle idling, the normal range of EGR Close Learning Value Bank 1 is 0 to 1 V. ·
In cases when EGR Close Learning Value Bank 1 is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close. |
Diesel Throttle
| Main fault | Stuck, does not move smoothly |
| Symptoms | ·
Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed. ·
Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur. |
| Data List | Actual Throttle Position Bank 1
·
0%: Fully closed ·
100%: Fully open ·
When the engine switch is on (IG) (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the engine switch is turned from on (IG) to off, the throttle is fully closed temporarily. |
Data List Related to Startability Malfunctions and Engine Stalls
Depending on the vehicle model, the applicable Data List items may vary. Data List items other than the ones used in the diagnostic procedure are for reference only.
Intake Manifold Absolute Pressure
Mass Air Flow Sensor
Intake Air Temperature
Coolant Temperature
Battery Voltage
Starter SW
Engine Speed Cylinder #1 to #4
(Output only when the "Check the Cylinder Compression" Active Test is performed)
Target Fuel Pressure (High)
Fuel Pressure (High)
Injection Feedback Value #1 to #4
Target Injection Volume
Actual Throttle Position Bank 1
Target EGR Valve Position No.1
Actual EGR Valve Position No.1
EGR Close Learning Value Bank 1
Vehicle Control History Freeze Frame Data Items Related to Startability Malfunctions and Engine Stalls
The frequency of the malfunction can be determined by confirming the number of times the symptom occurred.
Engine Stall Count
Engine Stall Count (Fuel Pressure Low)
Engine Difficult to Start Count (Engine Starting Time Long)
Engine Difficult to Start Count (Engine Stall Immediately After Starting)
Engine Difficult to Start Count (Immobiliser)
Explanation of Symptom
| Starting Trouble | For good starting it is essential to have:
·
Sufficient cranking speed. ·
Properly operating engine preheating system. ·
Good quality fuel. The fuel is ignited by the heat which is generated by compression pressure. With problems such as a depleted battery, the crankshaft speed can become low, or if the engine compression is poor due to leakage, the compression pressure will not rise and there will be difficulty starting. When the engine is cold, even if there is compression heat, it will escape from the combustion chamber. For this reason, when the engine is started when it is cold, the glow plug assemblies heat the compressed air. Also, after starting the engine, by charging the glow plug assemblies for a fixed time set according to the engine coolant temperature, diesel knocking and white smoke are prevented. The quantity of fuel injected is determined by the fuel pressure and also the amount of time the injector assembly is open. |
Trouble Area Chart According to Problem Cause
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.
If any other DTCs are output, perform troubleshooting for those DTCs first.
Make sure to reproduce the conditions present when the malfunction occurred.
Using the GTS, read the Data List to confirm the engine operating conditions. This information can be useful when troubleshooting.
The vehicle condition when the problem symptoms occurred can be determined using the Vehicle Control History.
As the Vehicle Control History data may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.
If the problem symptoms do not recur, attempt to reproduce the symptoms and conditions when the malfunction occurred based on the result of the customer problem analysis and Vehicle Control History. Place the priority on confirming the symptoms.
When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.
The suspected cause of the problem symptoms can be determined using the codes, items, and Freeze Frame Data within the Vehicle Control History.
When confirming the Freeze Frame Data, be sure to check all multi Freeze Frame Data.
When confirming the Freeze Frame Data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
If the malfunction is currently occurring, use the Data List to confirm the current vehicle condition. By using the Data List, more detailed vehicle information can be confirmed than by using the Vehicle Control History Freeze Frame Data by itself.
As Vehicle Control History may be stored when performing an Active Test, learning, etc., make sure to clear the Vehicle Control History before returning the vehicle to the customer.
Check the engine cranking condition.
| Result | Proceed to |
|---|---|
| Cranking is OK. | A |
Low cranking speed.
|
B |
| Does not crank at all. | C |
A
B
C
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: System Select / Health Check.
Check the DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| Engine related DTCs are output | B |
A
B
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).
It is also possible to display Vehicle Control History during the Health Check, if "Store All Data" is selected.
Confirm if any data relating to the problem symptoms exist in the Vehicle Control History.
The vehicle condition when the problem symptoms occurred can be determined by confirming the Vehicle Control History Freeze Frame Data.
As the Vehicle Control History data may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.
Using information from the customer about when the problem symptom occurred, find the Freeze Frame Data with the appropriate Key Cycle, Total Distance Traveled, etc., to find vehicle history that may be related to the problem symptoms.
Check the vehicle control history code and freeze frame data.
| Vehicle Control History | Vehicle Control History Freeze Frame Data | Suspected Area | Proceed to |
|---|---|---|---|
| Engine Stall is stored
(Vehicle Control History Code: X0800) |
"BATT Voltage" in freeze frame data is below 6 V | The battery may be fully depleted or the battery terminals may be loose. | B |
| - | - | A | |
| Engine Stall (Fuel Pressure Low) is stored
(Vehicle Control History Code: X0806) |
"Fuel Pressure (High)" in freeze frame data is below 25000 kPag (254.9 kgf/cm2, 3626 psi) | Problem supplying fuel to fuel supply pump assembly (low pressure side)
·
Ran out of fuel, air in fuel, fuel frozen (in this case, values of "Coolant Temperature" in freeze frame data are low) ·
Fuel filter element clog, fuel line clog (low pressure side) or fuel leak ·
Feed pump (in fuel supply pump assembly) malfunctioning Problem supplying fuel to fuel supply pump assembly (low pressure side) or problem on high pressure side ·
Fuel supply pump assembly (pre-stroke control valve operation malfunction) ·
Common rail assembly |
C |
| Engine Stall (Engine Starting Time Long) is stored
(Vehicle Control History Code: X0810) |
"Coolant Temperature" in freeze frame data is below 35°C (95°F) | Engine starting trouble which occurred with cold engine | D |
| "Engine Speed" in freeze frame data is less than 120 rpm | Engine starting trouble may have occurred because engine speed was too low
·
The battery may be fully depleted or the battery terminals may be loose. ·
The viscosity of the engine oil may be inappropriate (low viscosity oil is not used). |
B | |
| "BATT Voltage" in freeze frame data is below 6 V | Engine starting trouble may have occurred because battery is fully depleted | ||
| "Fuel Pressure (High)" in freeze frame data is below 10000 kPag | Problem supplying fuel to fuel supply pump assembly (low pressure side)
·
Ran out of fuel, air in fuel, fuel frozen (in this case, values of "Coolant Temperature" in freeze frame data are low) ·
Fuel filter element clog, fuel line clog (low pressure side) or fuel leak ·
Feed pump (in fuel supply pump assembly) malfunctioning |
C | |
| "Fuel Pressure (High)" in freeze frame data is below 25000 kPag | Problem supplying fuel to fuel supply pump assembly (low pressure side) or problem on high pressure side
·
Fuel supply pump assembly (Pre-stroke control valve operation malfunction) ·
Common rail Assembly ·
Injector assembly (if glow plug assembly is covered with fuel when removed, injector of corresponding cylinder may be stuck open) ·
Fuel line clog (high pressure side), fuel leak |
E | |
| - | - | A | |
| Engine Stall (Engine Stall Immediately After Starting) is stored
(Vehicle Control History Code: X0811) |
- | - | A |
| Engine Difficult to Start (Immobiliser) is stored
(Vehicle Control History Code: X0812) |
- | ·
Inspect engine immobiliser system. ·
Inspection looseness in battery terminal. ·
Inspect connection condition of ECM power supply system wiring. |
- |
| The malfunction is not currently occurring and there is no Vehicle Control History related to the problem symptoms stated by the customer. | A | ||
A
B
C
D
E
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Diesel Starting.
Take a snapshot when idling with no load after the engine is warmed up and when starting trouble is occurring.
A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
When there is trouble starting with a cold engine, take the snapshot when the engine is cold. Then warm up the engine (engine coolant temperature is 75°C (167°F) or higher) and after idling the vehicle for 1 minute (A/C off, electrical load off), take a snapshot of the data for 15 seconds while idling.
Take a snapshot when the problem is occurring, such as when the engine is cold. However, if the problem does not reoccur, it is acceptable to only take a snapshot after the engine is warmed up and when the engine is started.
| Proceed to |
|---|
| NEXT |
NEXT
Check Fuel Pressure (High) in the snapshot taken in procedure 4 when the engine was started.
| Result | Proceed to |
|---|---|
| At the point in the illustration labeled "a", Fuel Pressure (High) is less than 10000 kPag from the value of Fuel Pressure (High) when cranking started | A |
| At the point in the illustration labeled "c", Fuel Pressure (High) is below Target Fuel Pressure (High) by 15000 kPag or more | B |
| Fuel Pressure (High) increases to a value that is higher than Target Fuel Pressure (High) immediately after cranking, and, at the point in the illustration labeled "d", Fuel Pressure (High) is higher than Target Fuel Pressure (High) | C |
| Except above | D |
Even if Fuel Pressure (High) is temporarily higher than Target Fuel Pressure (High), as shown at the point in the illustration labeled "b", the fuel supply pump assembly is normal.
Fuel pressure is about 25000 to 35000 kPag when the engine is cranking and the engine coolant temperature is 0°C (32°F) or higher.
Fuel Pressure (High) increases rapidly during cranking.
A
B
C
D
Disconnect the inlet hose from the fuel supply pump assembly.
Operate the priming pump and check that fuel is being supplied to the fuel supply pump assembly.
Fuel is properly supplied to the fuel supply pump when the priming pump is operated.
When there is a lack of fuel, fuel pressure drops.
Inspect for fuel filter element assembly clogging (check that the fuel filter element assembly is not clogged).
Reconnect the inlet hose.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the pre-stroke control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| r6-1 - C150-3 (PCV+) | Always | Below 1 Ω |
| r6-2 - C150-4 (PCV-) | Always | Below 1 Ω |
| r6-1 or C150-3 (PCV+) - Body ground and other terminals | Always | 10 kΩ or higher |
| r6-2 or C150-4 (PCV-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the fuel supply pump assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Diesel Starting / Fuel Pressure (High) and Starter SW.
Start the engine.
Read the values while cranking and idling the engine.
| Result | Proceed to |
|---|---|
| The engine cannot be started or the engine can be started but Fuel Pressure (High) is below 20000 kPag 2 seconds after the Starter SW changes from OFF to ON | B |
| Except above | A |
A
B
Remove the glow plug assembly for all the cylinders.
Click hereEngine / Hybrid System>1GD-FTV (STARTING)>GLOW PLUG>REMOVAL
Visually check if there is fuel on the glow plug assemblies.
If there is fuel on a glow plug assembly, fuel may be leaking from an injector assembly.
After replacing an injector assembly, make sure that the common rail pressure (fuel pressure) is within 5000 kPag of the target fuel pressure while cranking the engine.
If there is fuel on a glow plug assembly, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.
Install the glow plug assembly.
Click hereEngine / Hybrid System>1GD-FTV (STARTING)>GLOW PLUG>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Check and repair or replace the clogged fuel pipe.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Check Fuel Pressure (High) in the snapshot taken in procedure 4 when the engine was warmed up.
| Result | Proceed to |
|---|---|
| Difference between Fuel Pressure (High) and Target Fuel Pressure (High) is 5000 kPag (51.0 kgf/cm2, 725 psi) or more | A |
| Except above | B |
A
B
Replace the fuel supply pump assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the injector assemblies of all cylinders.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL
When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.
Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Perform troubleshooting for DTC P062D96 during a startability malfunction, even if P062D96 is not output.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P020112
When troubleshooting the injector power source circuit, check the following locations, as one may contain the cause of the malfunction
EDU relay
Injector assembly circuit
ECM
When the engine cannot be started due to a malfunction in the injector power source circuit, once the DTCs are cleared, P062D96 cannot be stored even when the problem symptoms are reproduced and a startability malfunction occurs.
Since P062D96 cannot be stored when starting the engine, fuel injection cannot be performed even though fuel injection signals are output from the ECM. Therefore, using the GTS during a startability malfunction to check the data shows that an excessive amount of fuel is supplied to the common rail assembly by the fuel supply pump assembly, and as a result, the Fuel Pressure (High) is higher than the Target Fuel Pressure (High).
Perform the following procedure when a malfunction cannot be found during the troubleshooting procedure for P062D96 and the Fuel Pressure (High) when starting the engine is higher than the Target Fuel Pressure (High).
Perform the troubleshooting procedure for DTC P062D96 and proceed to the diagnostic flow situations where the engine does not start.
| Result | Proceed to |
|---|---|
| Injector power source circuit is normal | A |
| Injector power source circuit is abnormal | B |
A
B
Disconnect the injector assembly connectors.
Measure the resistance of the injector assembly.
No open circuit malfunction.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the injector assembly of the malfunctioning cylinder.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL
When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.
Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Check Injection Feedback Value #1 to #4 and Target Injection Volume in the snapshot taken in procedure 4 when the engine was idling.
| Result | Proceed to |
|---|---|
| Injection Feedback Value #1 to #4 are 5 mm3/st or less.
Target Injection Volume is more than 15 mm3/st. |
A* |
Injection Feedback Value for at least one cylinder is more than +5 mm3/st
|
B |
| Except above | C |
*: When this case occurs, usually symptoms may be noticeable, such as difficulty starting or lack of power.
The shift lever should be in neutral and the A/C switch and all accessory switches should be off.
A*
B
C
Replace the injector assemblies of all cylinders.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL
When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.
Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Use this Active Test to help determine whether a cylinder has compression loss or not.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed Cylinder #1 to #4.
Check the engine speed during the Active Test.
| Result | Proceed to |
|---|---|
| Except below | A |
| The values of Engine Speed Cylinder #1 to #4 are within 10 rpm of each other. | B |
When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.
A
B
Measure the compression of the cylinder that had a high speed during the "Check the Cylinder Compression" Active Test.
Check the cylinder compression pressure.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4 in the snapshot taken in procedure 4 when the engine was idling.
Record the value displayed for Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the injector assembly of the cylinder which displays a value of 5.0 mm3/st or higher for Injection Feedback Value #1 to #4 in step 20.
Only replace the injector assembly for the cylinder which displays an Injector Leaking Count #1 to #4 value of 1 or more, or i-ART Learning Status History #1 to #4 value of 1 Trip or more.
If Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4 both display 0, only replace the injector assembly for the cylinder which was determined to be malfunctioning using Injection Feedback Value #1 to #4.
It can be determined that the injector assembly is faulty as the corresponding cylinder is malfunctioning, but has no compression loss.
Replace the injector assembly of the malfunctioning cylinder.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL
When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.
Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Clean the fuel filter case and replace the fuel filter element assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT
Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Check Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4 in the snapshot taken in procedure 4 when the engine was idling.
| Result | Proceed to |
|---|---|
| The value for Injector Leaking Count #1 to #4 does not change from 0
The value for i-ART Learning Status History #1 to #4 does not change from 0 Trip |
A |
| The value for Injector Leaking Count #1 to #4 displays 1 or more
The value for i-ART Learning Status History #1 to #4 displays 1 Trip or more |
B |
A
B
Check the temperature when starting trouble occurs.
| Result | Proceed to |
|---|---|
| Difficult to start only for cold engine. | A |
| Difficult to start both for cold and warmed up engine. | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Diesel Starting / Coolant Temperature.
Read the value displayed on the GTS.
Coolant Temperature is not high when the engine is cold, and not low after the engine is warmed up.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the glow plug assembly.
Click hereEngine / Hybrid System>1GD-FTV (STARTING)>GLOW PLUG>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that only diesel fuel is being used.
Check that the fuel does not contain any impurities.
| Proceed to |
|---|
| NEXT |
NEXT
Only replace the injector assembly for the cylinder which displays an Injector Leaking Count #1 to #4 value of 1 or more, or i-ART Learning Status History #1 to #4 value of 1 Trip or more.
Replace the injector assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL
When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.
Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| Engine related DTCs are output | B |
A
B
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Check if the normal starting screen appears (check whether communication with the ECM is possible).
Use a GTS that is able to communicate with other vehicles.
Communication is possible (vehicle can be recognized).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Primary / Starter SW and Neutral Position SW or Clutch SW.
Read the value displayed on the GTS.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Starter SW | Cranking | ON |
| Neutral Position SW*1 | Shift lever in neutral | ON |
| Clutch SW*2 | Clutch pedal depressed | ON |
*1: Only for automatic transmission
*2: Only for manual transmission
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Manual transmission) | B |
| NG (for Automatic transmission) | C |
A
B
C
Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
Inspect the starting system.
Be sure to inspect the following areas:
Battery
Starter relay
Starter assembly
Entry and start system
Immobiliser system
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT