2011-2013 Land Cruiser · Service Manual Brake

C0210/33 Rear Speed Sensor RH Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the ECU. These signals are used to control the Multi-terrain ABS, EBD, BA, VSC, A-TRC, CRAWL and hill-start assist control systems. This speed sensor contains a sensor IC, which consists of 2 MREs (Magnetic Resistance Element). The speed sensor rotor, which consists of 48 sets of N and S poles that are arranged in a circle, is integrated with the inner race of the hub bearing.
To detect the rotation direction, the output waves are used to determine the relationship of the pulses that are generated by 2 MREs. Upon receiving this signal, the sensor IC outputs a forward or backward wave to the skid control ECU.
C173114E01
DTC Code
DTC Detection Condition
Trouble Area
C0210/33
C0215/34
When any of the following conditions is detected:
1. At a vehicle speed of 10 km/h (6 mph) or more, the pulses are not input for 1 second.
2. A momentary interruption of the speed sensor signal occurs at least 255 times when switching the ignition switch ON and off.
3. Continuous noise occurs in the speed sensor signals at a vehicle speed of 20 km/h (12 mph) or more.
4. The speed sensor signal circuit is open for 0.12 seconds or more.
  1. Rear speed sensor RH
  2. Rear speed sensor LH
  3. Harness or connector
  4. Speed sensor rotor
  5. Sensor installation
  6. Master cylinder solenoid (Skid control ECU)
C1238/38
C1239/39
Noise in the speed sensor signals occurs 75 times or more for 5 seconds when the vehicle speed is 20 km/h (12 mph) or more.
  1. Rear speed sensor RH
  2. Rear speed sensor LH
  3. Speed sensor rotor
  4. Sensor installation
  5. Master cylinder solenoid (Skid control ECU)

HINT:
  1. DTC C0210/33 and C1238/38 are for the rear speed sensor RH.
  2. DTC C0215/34 and C1239/39 are for the rear speed sensor LH.


WIRING DIAGRAM

C173115E02

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).


1. READ VALUE USING INTELLIGENT TESTER (RR/RL SPEED OPEN)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Speed Open
Rear speed sensor RH open detection / Error or Normal
Error: Momentary interruption
Normal: Normal
-
RL Speed Open
Rear speed sensor LH open detection / Error or Normal
Error: Momentary interruption
Normal: Normal
-
  1. Check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    OK:
    There are no momentary interruptions.

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED, RR/RL WHEEL DIRECTION)
  1. Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    Rear wheel speed sensor RH reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    A similar speed is indicated on the speedometer.
    RL Wheel Speed
    Rear wheel speed sensor LH reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    A similar speed is indicated on the speedometer.

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed.

  1. Check that the sensor signal conforms to the wheel direction.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Direction
    Rear wheel direction RH / Forward or Back
    Forward: Forward
    Back: Backward
    -
    RL Wheel Direction
    Rear wheel direction LH / Forward or Back
    Forward: Forward
    Back: Backward
    -

    OK:
    The wheel direction is displayed correctly.



NG
Go to step 4
OK


3. PERFORM SIGNAL CHECK
  1. Check if test mode (signal check) DTCs are output.

    HINT:
    Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.

    Result 
    Result
    Proceed to
    Test mode (signal check) DTC is output
    A
    Test mode (signal check) DTC is not output
    B



B
Go to step 10
A


4. INSPECT REAR SPEED SENSOR INSTALLATION
  1. Check the speed sensor installation (Click here).

    OK:
    The installation nut is tightened properly.
    There is no clearance between the sensor and rear axle.

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
INSTALL REAR SPEED SENSOR CORRECTLY (Click here)
OK


5. INSPECT SPEED SENSOR TIP
  1. Remove the rear speed sensor (Click here).

  1. Check the sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.

    NOTICE:
    Check the speed sensor signal after cleaning/replacement (Click here).



NG
CLEAN OR REPLACE REAR SPEED SENSOR (Click here)
OK


6. INSPECT REAR SPEED SENSOR

  1. C173117E18
    Install the rear speed sensor.

  1. Disconnect the z19 and/or z20 rear speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Switch Condition
    Specified Condition
    z19-2 (RR+) - Body ground
    Ignition switch off
    10 kΩ or higher
    z19-1 (RR-) - Body ground
    Ignition switch off
    10 kΩ or higher
    for LH:
    Tester Connection
    Switch Condition
    Specified Condition
    z20-2 (RL+) - Body ground
    Ignition switch off
    10 kΩ or higher
    z20-1 (RL-) - Body ground
    Ignition switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Rear Speed Sensor)
    *a
    for RH
    *b
    for LH



NG
REPLACE REAR SPEED SENSOR (Click here)
OK


7. INSPECT SKID CONTROL SENSOR WIRE

  1. C173122E06
    Disconnect the z19/z20 and Nz1 skid control sensor wire connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    z19-2 (RR+) - Nz1-4
    Always
    Below 1 Ω
    z19-2 (RR+) - Nz1-3
    Always
    10 kΩ or higher
    z19-2 (RR+) - Body ground
    Always
    10 kΩ or higher
    z19-1 (RR-) - Nz1-3
    Always
    Below 1 Ω
    z19-1 (RR-) - Nz1-4
    Always
    10 kΩ or higher
    z19-1 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    z20-2 (RL+) - Nz1-2
    Always
    Below 1 Ω
    z20-2 (RL+) - Nz1-1
    Always
    10 kΩ or higher
    z20-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    z20-1 (RL-) - Nz1-1
    Always
    Below 1 Ω
    z20-1 (RL-) - Nz1-2
    Always
    10 kΩ or higher
    z20-1 (RL-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Skid Control Sensor Wire)
    *a
    Sensor Side Connector
    *b
    Vehicle Side Connector
    *c
    for RH
    *d
    for LH

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE SKID CONTROL SENSOR WIRE (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)
  1. Disconnect the A24 skid control ECU connector and Nz1 skid control sensor wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    A24-5 (RR+) - Nz1-4
    Always
    Below 1 Ω
    A24-5 (RR+) - Body ground
    Always
    10 kΩ or higher
    A24-19 (RR-) - Nz1-3
    Always
    Below 1 Ω
    A24-19 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    A24-20 (RL+) - Nz1-2
    Always
    Below 1 Ω
    A24-20 (RL+) - Body ground
    Always
    10 kΩ or higher
    A24-6 (RL-) - Nz1-1
    Always
    Below 1 Ω
    A24-6 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT MASTER CYLINDER SOLENOID (SKID CONTROL ECU OUTPUT VOLTAGE)

  1. C173272E07
    Reconnect the A24 skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH:
    Tester Connection
    Switch Condition
    Specified Condition
    Nz1-4 - Body ground
    Ignition switch ON
    7.5 to 12 V
    for LH:
    Tester Connection
    Switch Condition
    Specified Condition
    Nz1-2 - Body ground
    Ignition switch ON
    7.5 to 12 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Skid Control Sensor Wire)
    Result 
    Result
    Proceed to
    OK
    A
    NG
    for LHD
    B
    for RHD
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A


10. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.

  1. Check if the same DTCs are output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output (When troubleshooting in accordance with the Diagnostic Trouble Code Chart)
    B
    DTC is not output (When troubleshooting in accordance with the Problem Symptoms Table)
    C



B
USE SIMULATION METHOD TO CHECK (Click here)

C
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A


11. REPLACE REAR SPEED SENSOR
  1. Replace the rear speed sensor (Click here).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


12. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.

  1. Check if the same DTCs are output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A


13. INSPECT SPEED SENSOR ROTOR
  1. Remove the rear axle hub and bearing assembly (Click here).

  1. Check the sensor rotor.

    OK:
    No scratches, oil, or foreign matter on the rotors.

    NOTICE:
    Check the speed sensor signal after cleaning/replacement (Click here).

    Result 
    Result
    Proceed to
    NG
    A
    OK
    for LHD
    B
    for RHD
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

CLEAN OR REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (SPEED SENSOR ROTOR) (Click here)


← C0200/31 Front Speed Sensor RH Circuit (+ C0205/32, C1235/35, C1236/36) (Sep 2011 – Dec 2011)C0226/21 SFR Solenoid Circuit (+ 7 more codes) (Sep 2011 – Dec 2011) →