The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term and long-term fuel trims.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air-fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air-fuel ratio is rich and an increase in the fuel injection volume if it is lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0171
P0174 |
With a warm engine and stable air-fuel ratio feedback, the fuel trim is considerably in error to the lean side (2 trip detection logic). | ·
Air induction system ·
Fuel injector blockage ·
Mass air flow meter assembly ·
Engine coolant temperature sensor ·
Fuel pressure ·
Gas leak from exhaust system ·
Open or short in air fuel ratio sensor (for Sensor 1) circuit ·
Air fuel ratio sensor (for Sensor 1) ·
Air fuel ratio sensor heater (for Sensor 1) ·
No. 1 integration relay ·
Air fuel ratio sensor heater and No. 1 integration relay circuits ·
PCV valve and hose ·
PCV hose connections ·
ECM ·
Wire harness or connector |
| P0172
P0175 |
With a warm engine and stable air-fuel ratio feedback, the fuel trim is considerably in error to the rich side (2 trip detection logic). | ·
Fuel injector leak or blockage ·
Mass air flow meter assembly ·
Engine coolant temperature sensor ·
Ignition system ·
Fuel pressure ·
Gas leak from exhaust system ·
Open or short in air fuel ratio sensor (for Sensor 1) circuit ·
Air fuel ratio sensor (for Sensor 1) ·
Air fuel ratio sensor heater (for Sensor 1) ·
No. 1 integration relay ·
Air fuel ratio sensor heater and No. 1 integration relay circuits ·
ECM |
When DTC P0171 or P0174 is stored, the actual air-fuel ratio is on the lean side. When DTC P0172 or P0175 is stored, the actual air-fuel ratio is on the rich side.
If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 or P0174 may be stored. The MIL is then illuminated.
When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is higher than 75°C [167°F]), the system is functioning normally.
Under closed-loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the ECM estimated fuel injection volumes also affect the average fuel trim learning value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learning value of the air-fuel ratio). If the average fuel trim learning value exceeds the malfunction threshold, the ECM interprets this as a fault in the fuel system and stores a DTC.
Example:
If the average fuel trim learning value is +35% or more, or -35% or less, the ECM interprets this as a fuel system malfunction.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and turn the GTS on [A].
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [B].
With the engine warmed up, idle the engine for 2 minutes or more [C].
Drive the vehicle at a speed between 60 and 100 km/h (38 and 63 mph) for 5 minutes or more [D].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
Refer to DTC P2195 (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>P2195).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
A low air fuel ratio sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
A high air fuel ratio sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
| P0171, P0172, P0174 or P0175 is output | A |
| P0171, P0172, P0174 or P0175 and other DTCs are output | B |
If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.
A
B
Check the PCV hose connections (See page Engine / Hybrid System>1UR-FE (EMISSION CONTROL)>EMISSION CONTROL SYSTEM(w/ Secondary Air Injection System)>ON-VEHICLE INSPECTION).
PCV hose is connected correctly and is not damaged.
OK
NG
Check the air induction system for vacuum leaks (See page Engine / Hybrid System>1UR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).
No leaks in air induction system.
OK
NG
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
Perform the Control the Injection Volume operation with the engine idling.
Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the GTS.
Change the fuel injection volume within the range of -12.5% to +12.5%. The injection volume can be changed in fine gradations.
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
If the air fuel ratio sensor output voltage does not change (almost no reaction) while performing the Active Test, the air fuel ratio sensor may be malfunctioning.
| GTS Display (Sensor) | Injection Volume | Status | Voltage |
|---|---|---|---|
| AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio) |
+12.5% | Rich | Below 3.1 V |
| AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio) |
-12.5% | Lean | Higher than 3.4 V |
| O2S B1S2 or O2S B2S2
(Heated oxygen) |
+12.5% | Rich | Higher than 0.55 V |
| O2S B1S2 or O2S B2S2
(Heated oxygen) |
-12.5% | Lean | Below 0.4 V |
| Status of AFS Voltage B1S1 or AFS Voltage B2S1 | Status of O2S B1S2 or O2S B2S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition | Suspected Trouble Area | Proceed to |
|---|---|---|---|---|
| Lean/Rich | Lean/Rich | Normal | - | A |
| Lean | Lean | Actual air fuel ratio lean | ·
PCV valve and hose ·
PCV hose connections ·
Fuel injector assembly blockage ·
Gas leaks from exhaust system ·
Intake system ·
Fuel pressure ·
Mass air flow meter assembly ·
Engine coolant temperature sensor |
A |
| Rich | Rich | Actual air fuel ratio rich | ·
Fuel injector assembly leakage or blockage ·
Gas leaks from exhaust system ·
Ignition system ·
Fuel pressure ·
Mass air flow meter assembly ·
Engine coolant temperature sensor |
A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | Air fuel ratio sensor | B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | Air fuel ratio sensor | B |
Lean: During the Control the Injection Volume Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.
Rich: During the Control the Injection Volume Active Test, the AFS Voltage is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.
Lean/Rich: During the Control the Injection Volume Active Test, the output voltage of the heated oxygen sensor alternates correctly.
Refer to "Data List / Active Test" [AFS Voltage B1S1, AFS Voltage B2S1, O2S B1S2 and O2S B2S2] (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST).
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Read Coolant Temp twice, when the engine is both cold and warmed up.
With cold engine: Same as ambient air temperature.
With warm engine: Between 75°C and 100°C (167°F and 212°F).
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 3000 rpm.
Between 18.3 gm/sec. and 25.8 gm/sec. (shift lever: N; A/C: Off).
OK
NG
Check the fuel pressure (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Check for exhaust gas leaks.
No gas leaks.
OK
NG
OK
NG
Check the injection and volume (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL INJECTOR>INSPECTION).
OK
NG
OK
NG
OK
NG
OK
NG
Replace the air fuel ratio sensor (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
| DTC P0171, P0172, P0174 or P0175 is output | A |
| DTC is not output | B |
A
B
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).
Repair any problems.
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
| DTC P0171, P0172, P0174 or P0175 is output | A |
| DTC is not output | B |
A
B
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C50-3 (VG) - C46-74 (VG) | Always | Below 1 Ω |
| C50-2 (E2G) - C46-75 (E2G) | Always | Below 1 Ω |
| C50-3 (VG) or C46-74 (VG) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C50-3 (VG) - C45-74 (VG) | Always | Below 1 Ω |
| C50-2 (E2G) - C45-75 (E2G) | Always | Below 1 Ω |
| C50-3 (VG) or C45-74 (VG) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the mass air flow meter assembly (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL).
If the result of the inspection performed in step 6 indicated no problem, proceed to the next step without replacing the mass air flow meter assembly.
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P0171, P0172, P0174 or P0175 is output | B |
A
B
OK
NG
Inspect the No. 1 integration relay (A/F) (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).
OK
NG