Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P1603  Engine Stall History  P1605  Rough Idling  


DESCRIPTION

P1603

After starting the engine, this DTC is stored when the engine stops without the engine switch being operated.

Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle has ran out of fuel before performing troubleshooting, as this DTC is also stored when the engine stalls due to running out of fuel.

DTC No. DTC Detection Condition Trouble Area
P1603 After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the engine switch being operated for 0.5 seconds or more (1 trip detection logic).
·

Air leak in intake system

·

Purge VSV

·

Mass air flow meter assembly

·

Engine coolant temperature sensor

·

Wire harness or connector

·

Air fuel ratio sensor

·

Power supply circuit (purge VSV, fuel injector assembly, ignition coil assembly)

·

Fuel pump

·

Fuel pump control system

·

Fuel line

·

Throttle body assembly

·

Camshaft timing oil control valve assembly

·

Air conditioning system

·

Power steering system

·

Electrical load signal system

·

A/T system

·

Park/neutral position switch assembly

·

ECM



P1605

This DTC is stored if the engine speed drops below the set speed.

Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when idling is unstable due to running out of fuel.

DTC No. DTC Detection Condition Trouble Area
P1605 After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less (1 trip detection logic).
·

Air leak in intake system

·

Purge VSV

·

Mass air flow meter assembly

·

Engine coolant temperature sensor

·

Wire harness or connector

·

Air fuel ratio sensor

·

Power supply circuit (purge VSV, fuel injector assembly, ignition coil assembly)

·

Fuel pump

·

Fuel pump control system

·

Fuel line

·

Throttle body assembly

·

Camshaft timing oil control valve assembly

·

Knock sensor

·

Ignition coil assembly

·

Fuel injector assembly

·

Spark plug(s)

·

Air conditioning system

·

Power steering system

·

Electrical load signal system

·

A/T system

·

Park/neutral position switch assembly

·

ECM



CAUTION / NOTICE / HINT

HINT:
·

In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P1603 and P1605 are used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.

As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.

·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Use any information from the customer problem analysis about the condition of the vehicle at the time when the problem occurred (how the engine stopped, conditions when the engine was restarted, etc.) as a reference.

Symptom Suspected Area
Engine vibration occurs and engine stops Air-fuel ratio abnormal
Engine stops with no engine vibration Ignition system, injection stoppage, high load from external parts
Engine can be started with accelerator pedal depressed Insufficient air volume
Rough idling after engine started Air-fuel ratio abnormal, abnormal combustion

·

Read freeze frame data using the GTS. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

·

When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

·

When DTC P1603 (Engine Stall History) is stored, DTC P1605 (Rough Idling) is also stored. When confirming freeze frame data, check DTC P1605. The ECM stores DTC P1605 first. Therefore, 5 sets of freeze frame data can be confirmed through DTC P1605, enabling the technician to obtain more information.

·

When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.

·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.

·

Inspections take into account the fact that the malfunction may not have reoccurred and place emphasis on checking the vehicle conditions present at the time when the malfunction occurred.

·

When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.



Inspection flow:

Using freeze frame data, narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred.


P1603:

A226063E01
0.219,0.775 1.114,1.107 0.895,0.332 10 While idling or while driving? 1.824,0.778 3.155,1.478 1.332,0.700 10 Did the engine speed decrease slowly or rapidly when engine stall occurred? 0.189,0.599 0.373,0.783 0.184,0.184 10 1: 1.824,0.599 2.007,0.783 0.184,0.184 10 2: 3.925,0.778 4.961,1.295 1.036,0.517 10 Was the air-fuel ratio abnormal or normal? 3.925,0.599 4.109,0.783 0.184,0.184 10 3: 5.961,0.75 6.904,0.915 0.943,0.165 10 Intake air leak 5.781,1.758 7.031,1.923 1.250,0.165 10 Sensor malfunction 1.242,5.833 2.492,5.998 1.250,0.165 10 Sensor malfunction 5.748,2.763 7.061,2.928 1.313,0.165 10 Fuel supply problem 1.214,7.822 2.527,7.987 1.313,0.165 10 Fuel supply problem 6.036,3.459 6.746,3.809 0.710,0.350 10 Air volume insufficient 5.953,4.47 6.878,4.802 0.924,0.332 10 Ignition timing incorrect 3.41,4.481 4.492,4.822 1.082,0.341 10 Injection and ignition stoppage 1.337,6.554 2.418,6.895 1.082,0.341 10 Injection and ignition stoppage 3.497,5.48 4.394,5.821 0.897,0.341 10 Load from external parts 1.31,0.134 1.697,0.299 0.387,0.165 10 Idling 0.096,2.544 0.557,2.709 0.461,0.165 10 Driving 2.972,0.134 4.156,0.299 1.184,0.165 10 Decreased Slowly 1.16,2.544 2.400,2.746 1.239,0.202 10 Decreased Rapidly 5.027,0.134 5.692,0.317 0.665,0.184 10 Abnormal 3.832,2.544 4.330,2.709 0.498,0.165 10 Normal

1:
·

If the engine stalled when the intake air volume was low (during idling or deceleration), there may be a decrease in torque due to an incorrect air-fuel ratio, etc.

·

If the engine stalled when the intake air volume was high (during driving or acceleration), there may be a major malfunction such as continuous misfire due to ignition stoppage, fuel injection stoppage, etc. and the torque drops to zero.


2:
·

If the engine speed decreased slowly, there may have been a decrease in torque due to an air-fuel ratio that was incorrect (by approximately 20 to 30%), etc.

·

If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.


3:
·

If the air-fuel ratio is abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.

·

If the vehicle was normal, the air volume may have been insufficient, the ignition timing may have been incorrect or the EGR valve may have been stuck open.


P1603 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).

Vehicle State Engine Speed Suspected Area Primary Parts to Inspect Procedure
Idling or decelerating Slowly decreases and engine stalls Ignition system abnormal Igniter abnormal
·

Power supply circuit

·

Ignition coil assemblies

·

Spark plug


34, 48
Air-fuel ratio abnormal Air suction
·

Intake system connections

·

Purge VSV system

·

Brake booster


5, 6
Sensor malfunction (value from sensor too lean)
·

Mass air flow meter

·

Engine coolant temperature sensor

·

Air fuel ratio sensor system

·

Water inlet with thermostat sub-assembly


7 to 19
Sensor malfunction (value from sensor too rich) 35 to 47
Fuel supply problem
·

Fuel pump control circuit

·

Purge VSV system

·

Fuel line

·

ECM


20 to 33
Intake air volume insufficient Problem with air passage
·

Intake system connections

·

Mass air flow meter

·

Brake booster

·

PCV valve and hose

·

Purge VSV system


49 to 51
Excessive valve overlap
·

Camshaft timing oil control valve


52 to 55
Ignition timing incorrect Does not operate as expected
·

Knock sensor

·

Engine coolant temperature sensor

·

Mass air flow meter


56 to 60
Rapidly decreases and engine stalls* Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (fuel injector assembly, ignition coil assembly)


61, 62
External part malfunctioning Increase in load
·

Air conditioning system

·

Electrical load signal system

·

Power steering system

·

A/T system

·

Park/neutral position switch assembly


63 to 65
Accelerating - Crankshaft position sensor or VVT sensor malfunction Power temporarily cut
·

Check DTCs


1
Mass air flow meter Foreign matter adhesion
·

Mass air flow meter


66 to 69
Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (fuel injector assembly, ignition coil assembly)


70, 71
Fuel supply problem Fuel leak, clog
·

Fuel pump control circuit

·

Fuel line


72 to 76

*: If the engine stalls immediately after the injection method is switched from port injection to direct injection, the injector driver may be malfunctioning.

P1605:

A226064E01
0.498,0.514 0.668,0.688 0.170,0.174 10 1: 0.498,0.71 1.640,1.213 1.142,0.503 10 Did the engine speed decrease slowly or rapidly? 2.819,0.514 2.989,0.688 0.170,0.174 10 2: 2.819,0.71 3.961,1.213 1.142,0.503 10 Was the air-fuel ratio abnormal or normal? 5.69,0.715 6.633,0.881 0.943,0.165 10 Intake air leak 5.549,1.727 6.788,1.892 1.239,0.165 10 Sensor malfunction 5.522,2.722 6.799,2.924 1.276,0.202 10 Fuel supply problem 4.034,2.065 4.742,2.384 0.708,0.319 10 Air volume insufficient 3.925,3.05 4.850,3.382 0.924,0.332 10 Ignition timing incorrect 1.582,2.706 2.673,3.057 1.091,0.350 10 Injection and ignition stoppage 1.662,3.707 2.586,4.057 0.924,0.350 10 Load from external parts 1.908,0.876 2.628,1.226 0.721,0.350 10 Decreased Slowly 0.264,1.847 0.984,2.197 0.721,0.350 10 Decreased Rapidly 4.299,0.894 4.945,1.059 0.647,0.165 10 Abnormal 2.776,1.847 3.293,2.012 0.517,0.165 10 Normal

1:
·

If the engine speed decreased slowly, there may have been a decrease in torque due an air-fuel ratio that was incorrect (by approximately 20 to 30%), etc.

·

If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.


2:
·

If the air-fuel ratio is abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.

·

If the vehicle was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.


P1605 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).

Engine Speed Suspected Area Primary Parts to Inspect Procedure
Slowly decreases and engine stalls Ignition system abnormal Igniter abnormal
·

Power supply circuit

·

Ignition coil assemblies

·

Spark plug


34, 48
Air-fuel ratio abnormal Air suction
·

Intake system connections

·

Purge VSV system

·

Brake booster


5, 6
Sensor malfunction (value from sensor too lean)
·

Mass air flow meter

·

Engine coolant temperature sensor

·

Air fuel ratio sensor system

·

Water inlet with thermostat sub-assembly


7 to 19
Sensor malfunction (value from sensor too rich) 35 to 47
Fuel supply problem
·

Fuel pump control circuit

·

Purge VSV system

·

Fuel line

·

ECM


20 to 33
Intake air volume insufficient Problem with air passage
·

Intake system connections

·

Mass air flow meter

·

Brake booster

·

PCV valve and hose

·

Purge VSV system


49 to 51
Excessive valve overlap
·

Camshaft timing oil control valve


52 to 55
Ignition timing incorrect Does not operate as expected
·

Knock sensor

·

Engine coolant temperature sensor

·

Mass air flow meter


56 to 60
Rapidly decreases and engine stalls* Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (fuel injector assembly, ignition coil assembly)


61, 62
External part malfunctioning Increase in load
·

Air conditioning system

·

Electrical load signal system

·

Power steering system

·

A/T system

·

Park/neutral position switch assembly


63 to 65

*: If the engine stalls immediately after the injection method is switched from port injection to direct injection, the injector driver may be malfunctioning.

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Read the DTCs (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
Only DTC P1603 and P1605 are output A
DTCs other than P1603 and P1605 are output B

HINT:

If any DTCs other than P1603 or P1605 are output, troubleshoot those DTCs first.




A

2.CHECK FREEZE FRAME DATA

B

2.CHECK FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

OK:

Immobiliser Fuel Cut is OFF.


Result
Result Proceed to
Abnormal A
Normal B



A

3.CHECK ENGINE IMMOBILISER SYSTEM

B

4.READ FREEZE FRAME DATA
3.CHECK ENGINE IMMOBILISER SYSTEM
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Idle the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Immobiliser Communication and Immobiliser Fuel Cut.


e.

Check the Data List indication.

Result
Data List Item Result
Immobiliser Communication ON
Immobiliser Fuel Cut OFF



OK

4.READ FREEZE FRAME DATA

NG

CHECK ENGINE IMMOBILISER SYSTEM

4.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Problem Symptom Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
Closed Throttle Position SW Engine Speed Total of Short FT and Long FT
When idling or decelerating, engine speed slowly decreases and engine stalls All 5 sets of freeze frame data are ON Decreases slowly*1 All 5 sets of freeze frame data are +15% or more*2
·

Air suction


·

Sensor malfunction (value from sensor too lean)


·

Fuel supply problem


A
At least 1 of the 5 sets of freeze frame data is -15% or less*3 Sensor malfunction (value from sensor too rich) B
All 5 sets of freeze frame data are from -15% to +15%
·

Intake air volume insufficient


·

Ignition timing incorrect


C
When idling or decelerating, engine speed rapidly decreases and engine stalls Decreases rapidly*1 -
·

Injection stoppage, ignition stoppage


·

Load from external parts


D
When accelerating or driving at constant speed, engine stalls*4 At least one is OFF - -
·

Sensor malfunction


·

Injection stoppage, ignition stoppage


·

Fuel supply problem


E

A215381E01
0.072,0.032 2.177,0.197 2.105,0.165 10 Rapid Decrease in Engine Speed 2.333,0.377 2.702,0.561 0.369,0.184 10 (rpm) 2.389,0.723 2.665,0.869 0.276,0.147 10 800 2.389,0.928 2.665,1.075 0.276,0.147 10 600 2.389,1.126 2.665,1.272 0.276,0.147 10 400 2.389,1.331 2.665,1.478 0.276,0.147 10 200 2.548,1.529 2.689,1.675 0.142,0.147 10 0 3.038,1.642 3.235,1.798 0.198,0.156 10 #1 3.472,1.642 3.670,1.798 0.198,0.156 10 #2 3.935,1.642 4.132,1.798 0.198,0.156 10 #3 4.153,1.642 4.350,1.798 0.198,0.156 10 #4 4.377,1.642 4.574,1.798 0.198,0.156 10 #5 4.985,1.105 6.058,1.261 1.073,0.156 10 400 rpm or more 1.216,1.019 2.122,1.203 0.906,0.184 10 Engine Speed 2.702,1.944 4.816,2.128 2.114,0.184 10 Freeze Frame Data Storage Point

HINT:
·

*1: A rapid decrease in engine speed may be caused by an electrical fault in the shared wiring of all or a number of cylinders, an increase in load from external parts, etc. The engine speed is considered to have decreased rapidly if either of the following conditions applies.

Otherwise, the engine speed is considered to have decreased slowly.

(a)

In the freeze frame data, the decrease in engine speed from #3 to #5 is 400 rpm or more.

(b)

In the freeze frame data, the engine speed at #5 is 120 rpm or less.



·

If the vehicle speed is 30 km/h or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transmission. Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.

·

*2: When a DTC is stored, feedback compensation increases because the air-fuel ratio is determined to be lean.

·

*3: When a DTC is stored, feedback compensation decreases because the air-fuel ratio is determined to be rich.

·

*4: This item should be checked when DTC P1603 is output and is not necessary to check when only P1605 is output.





A

5.CHECK INTAKE SYSTEM

B

34.CHECK IGNITION SYSTEM

C

48.CHECK IGNITION SYSTEM

D

61.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)

E

66.CHECK FREEZE FRAME DATA
5.CHECK INTAKE SYSTEM
a.

Check for air leakage in the intake system [due to vacuum hose disconnection, cracks, damaged gaskets, etc.] (See page Engine / Hybrid System>1UR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

HINT:
·

If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.

·

If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.



OK:

There is no air leakage.




OK

6.CHECK PURGE VSV

NG

REPAIR OR REPLACE INTAKE SYSTEM

6.CHECK PURGE VSV
a.
A201060

Disconnect the purge hose (on the canister side) of the purge VSV.


b.

Start the engine.


c.

Idle the engine.


d.

Disconnect the connector of the purge VSV.


e.

Check if air flows through the purge VSV.

OK:

Air does not flow.



f.

Connect the connector of the purge VSV.


g.

Connect the purge hose of the purge VSV.

HINT:

When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).




OK

7.READ FREEZE FRAME DATA

NG

7.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Calculate Load Below 90% of the current value of the vehicle*1 Mass air flow meter assembly A
AFS Voltage B1S1
AFS Voltage B2S1
3.3 V or higher*2
·

Air fuel ratio sensor

·

Wire harness or connector

·

Actual air-fuel ratio abnormal


B

HINT:
·

*1: If the mass air flow meter is malfunctioning and incorrectly measures the pressure to be less than the actual intake manifold pressure, the freeze frame data will show a low engine load value.

·

*2: If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air-fuel ratio is lean, the actual air-fuel ratio will become rich and the engine may stall.





A

8.CHECK MASS AIR FLOW METER ASSEMBLY

B

11.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)
8.CHECK MASS AIR FLOW METER ASSEMBLY
a.

Remove the mass air flow meter assembly.


b.

Check for foreign matter in the airflow passage of the mass air flow meter.

Result
Result Proceed to
Visible foreign matter is not present A
Visible foreign matter is present B


c.

Install the mass air flow meter assembly.

HINT:

Even if the results are normal, the mass air flow meter may have been malfunctioning. Continue this inspection procedure until step 22, and if there are no problems with other parts, replace the mass air flow meter assembly (refer to step 55).




A

9.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)

B

9.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)
a.

Check the harnesses and connectors, referring to DTC P0102 inspection procedure (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>P0102).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

10.PERFORM DRIVE TEST

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.PERFORM DRIVE TEST
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the GTS, read the value of Calculate Load in the Data List.

Standard
Data List Specified Condition
Calculate Load 90 to 110% of the current value of the vehicle

Result
Result Proceed to
Abnormal A
Normal B



A

B

14.READ FREEZE FRAME DATA
11.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)
a.
A385106E01
0.865,0.021 2.021,0.26 1.156,0.24 10 false Injection Volume 0.979,0.406 1.521,0.646 0.542,0.24 10 false +12.5% 1.021,0.698 1.5,0.938 0.479,0.24 10 false -12.5% 0.427,1.604 3.25,1.875 2.823,0.271 10 false Air Fuel Ratio Sensor Output Voltage 0.417,2.156 1.688,2.354 1.271,0.198 10 false Higher than 3.4 V 0.75,2.51 1.594,2.729 0.844,0.219 10 false Below 3.1 V 2.854,2.281 3.188,2.521 0.333,0.24 10 false OK 2.781,4.031 3.115,4.271 0.333,0.24 10 false OK 0.375,3.406 2.896,3.646 2.521,0.24 10 false Heated Oxygen Sensor Output Voltage 0.385,3.865 1.646,4.094 1.26,0.229 10 false Higher than 0.55 V 0.792,4.25 1.625,4.49 0.833,0.24 10 false Below 0.4 V

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.


d.

Idle the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.


f.

Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.

Standard:
GTS Display Specified Condition
Control the Injection Volume (+12.5%) Air fuel ratio sensor output voltage is below 3.1 V
Control the Injection Volume (-12.5%) Air fuel ratio sensor output voltage is higher than 3.4 V


Result
Result Proceed to
Abnormal A
Normal B

HINT:
·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.





A

12.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR POWER SOURCE)

B

14.READ FREEZE FRAME DATA
12.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR POWER SOURCE)
a.

Check the harnesses and connectors, referring to DTC P0031 inspection procedure (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>P0031).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P2237 inspection procedure (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>P2237).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

14.READ FREEZE FRAME DATA

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Proceed to
Initial Engine Coolant Temp, Ambient Temperature, Initial Intake Air Temp Difference in temperature between each item is less than 10°C*1 A
Difference in temperature between each item is 10°C or more*2 B

HINT:
·

*1: A long time had elapsed after stopping the engine.

·

*2: A long time had not elapsed after stopping the engine.





A

15.READ FREEZE FRAME DATA

B

17.READ FREEZE FRAME DATA
15.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

A217929E01
0.467,0.856 2.887,1.519 2.420,0.663 10 Engine Coolant Temperature Increase after Engine Start (Engine Coolant Temperature - Engine Coolant Temperature at Engine Start) 3.423,0.037 3.718,0.234 0.295,0.198 10 (°C) 5.609,2.116 6.223,2.286 0.614,0.170 10 (Minutes) 5.16,1.69 5.316,1.846 0.156,0.156 10 A 4.964,0.779 5.120,0.935 0.156,0.156 10 C 3.891,0.493 4.047,0.649 0.156,0.156 10 B 3.563,2.39 5.573,2.546 2.010,0.156 10 Time Elapsed after Engine Start

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time Range A
·

Engine coolant temperature sensor

·

Thermostat


A
Range B Engine coolant temperature sensor B
Range C - C

HINT:

This step is not directly related to engine stall.




A

16.INSPECT THERMOSTAT

B

18.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

C

20.READ FREEZE FRAME DATA
16.INSPECT THERMOSTAT
HINT:

For the thermostat inspection, refer to the following procedures (See page Engine / Hybrid System>1UR-FE (COOLING)>THERMOSTAT>INSPECTION).


Result
Result Proceed to
Abnormal A
Normal B


A

B

18.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
17.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Coolant Temp 120°C or higher Engine coolant temperature sensor A
Coolant Temp, Ambient Temp for A/C Engine coolant temperature is lower than outside temperature by 15°C or more Engine coolant temperature sensor
Both freeze frame data items listed above Values are other than above - B



A

18.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

20.READ FREEZE FRAME DATA
18.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
HINT:

For the engine coolant temperature sensor inspection, refer to the following procedures (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).


Result
Result Proceed to
Abnormal A
Normal B


A

19.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE)

B

19.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE)
a.

Disconnect the ECM connector.


b.

Disconnect the engine coolant temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C18-2 - C46-76 (THW) Always Below 1 Ω
C18-1 - C46-98 (E2) Always Below 1 Ω
C18-2 or C46-76 (THW) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C18-2 - C45-76 (THW) Always Below 1 Ω
C18-1 - C45-98 (E2) Always Below 1 Ω
C18-2 or C45-76 (THW) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

20.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
EVAP (Purge) VSV At least 1 of the 5 sets of freeze frame data is not 0% Purge VSV A
All 5 sets of freeze frame data are 0% - B

HINT:

If the purge VSV is stuck closed, air-fuel ratio compensation by the purge VSV is incorrectly adjusted, and then the air-fuel ratio becomes lean and the engine may stall.




A

21.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)

B

29.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY)
21.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A200511E01
0.55,0.157 1.109,0.306 0.559,0.149 10 VSV ON 2.222,0.157 2.843,0.306 0.621,0.149 10 VSV OFF 0.593,1.471 1.152,1.627 0.559,0.156 10 Air flows 1.985,1.471 3.058,1.627 1.073,0.156 10 Air does not flow

Disconnect the purge hose (on the canister side) of the purge VSV.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.


f.

Operate the purge VSV and check the airflow.

Standard:
Activate the VSV for Evap Control Specified Condition
ON Air flows
OFF Air does not flow


Result
Result Proceed to
NG A
OK B


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.




A

22.INSPECT PURGE VSV

B

29.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY)
22.INSPECT PURGE VSV

OK

23.CHECK TERMINAL VOLTAGE (PURGE VSV POWER SOURCE)

NG

23.CHECK TERMINAL VOLTAGE (PURGE VSV POWER SOURCE)
a.
U162866E01
0.4,1.812 0.674,1.954 0.274,0.142 10 C55 0.242,0.212 0.425,0.402 0.184,0.191 10 *a

Disconnect the purge VSV connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C55-1 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Purge VSV)

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

24.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

REPAIR VACUUM SWITCHING VALVE ASSEMBLY NO.1

24.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C55-2 - C46-63 (PRG) Always Below 1 Ω
C55-2 or C46-63 (PRG) - Body ground Always 10 kΩ or higher

foe LHD
Tester Connection Condition Specified Condition
C55-2 - C45-63 (PRG) Always Below 1 Ω
C55-2 or C45-63 (PRG) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

25.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.




NEXT

26.READ VALUE USING GTS (EVAP (Purge) VSV)
26.READ VALUE USING GTS (EVAP (Purge) VSV)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine for 15 minutes or more.


d.

Using the GTS, read the value of EVAP (Purge) VSV in the Data List.

Standard
Data List Specified Condition
EVAP (Purge) VSV Value other than 0% is displayed

Result
Result Proceed to
Abnormal A
Normal B



A

27.PERFORM ACTIVE TEST USING GTS

B

27.PERFORM ACTIVE TEST USING GTS
a.
A200511E01
0.55,0.157 1.109,0.306 0.559,0.149 10 VSV ON 2.222,0.157 2.843,0.306 0.621,0.149 10 VSV OFF 0.593,1.471 1.152,1.627 0.559,0.156 10 Air flows 1.985,1.471 3.058,1.627 1.073,0.156 10 Air does not flow

Disconnect the purge hose (on the canister side) of the purge VSV.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.


f.

Operate the purge VSV and check the airflow.

Standard:
Activate the VSV for Evap Control Specified Condition
ON Air flows
OFF Air does not flow


Result
Result Proceed to
NG A
OK B


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.




A

28.CHECK CONNECTOR CONNECTION CONDITION (ECM)

B

28.CHECK CONNECTOR CONNECTION CONDITION (ECM)
a.

Check the ECM connector connection condition.

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

NG

CONNECTOR CORRECTLY

29.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Duty.


e.

When performing the Active Test, check for an operating sound from the fuel pump.

Standard
Control the Fuel Pump Duty Specified Condition
25 or 80% Operating sound heard
OFF Operating sound not heard

Result
Result Proceed to
Abnormal A
Normal B

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.

·

If the fuel pump operating noise is abnormal, proceed to step 30.





A

30.INSPECT FUEL PUMP

B

31.CHECK FUEL SYSTEM
30.INSPECT FUEL PUMP
a.


OK

NG

31.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check the fuel leaks.

·

Check the fuel pressure.

·

Check the fuel pressure (for high pressure).

HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



Result
Result Proceed to
Abnormal A
Normal B



A

32.CHECK FUEL SYSTEM

B

32.CHECK FUEL SYSTEM
a.

Check for foreign matter, such as iron particles, around the fuel pump, fuel pump filter and inside the fuel tank, and for signs that the fuel pump was stuck.

Result
Result Proceed to
There is foreign matter or signs that fuel pump was stuck A
There is no foreign matter and no signs that fuel pump was stuck B

HINT:

If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.




A

33.CHECK FUEL SYSTEM

B

REPAIR OR REPLACE FUEL SYSTEM

33.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check the fuel leaks.

·

Check the fuel pressure.

·

Check the fuel pressure (for high pressure).

HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



Result
Result Proceed to
Abnormal A
Normal B



OK

END

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

34.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).



OK

35.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

35.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Calculate Load Below 90% of the current value of the vehicle*1 Mass air flow meter assembly A
AFS Voltage B1S1
AFS Voltage B2S1
3.3 V or higher*2
·

Air fuel ratio sensor

·

Wire harness or connector

·

Actual air-fuel ratio abnormal


B

HINT:
·

*1: If the mass air flow meter is malfunctioning and incorrectly measures the pressure to be less than the actual intake manifold pressure, the freeze frame data will show a low engine load value.

·

*2: If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air-fuel ratio is lean, the actual air-fuel ratio will become rich and the engine may stall.





A

36.CHECK MASS AIR FLOW METER ASSEMBLY

B

39.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)

C

42.READ FREEZE FRAME DATA
36.CHECK MASS AIR FLOW METER ASSEMBLY
a.

Remove the mass air flow meter assembly.


b.

Check for foreign matter in the airflow passage of the mass air flow meter.

Result
Result Proceed to
Visible foreign matter is present A
Visible foreign matter is not present B



A

37.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)

B

37.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)
a.

Check the harnesses and connectors, referring to DTC P0102 inspection procedure (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>P0102).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

38.PERFORM DRIVE TEST

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

38.PERFORM DRIVE TEST
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the GTS, read the value of Calculate Load in the Data List.

Standard
Data List Specified Condition
Calculate Load 90 to 110% of the current value of the vehicle



OK

39.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)

NG

39.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)
a.
A385106E01
0.865,0.021 2.021,0.26 1.156,0.24 10 false Injection Volume 0.979,0.406 1.521,0.646 0.542,0.24 10 false +12.5% 1.021,0.698 1.5,0.938 0.479,0.24 10 false -12.5% 0.427,1.604 3.25,1.875 2.823,0.271 10 false Air Fuel Ratio Sensor Output Voltage 0.417,2.156 1.688,2.354 1.271,0.198 10 false Higher than 3.4 V 0.75,2.51 1.594,2.729 0.844,0.219 10 false Below 3.1 V 2.854,2.281 3.188,2.521 0.333,0.24 10 false OK 2.781,4.031 3.115,4.271 0.333,0.24 10 false OK 0.375,3.406 2.896,3.646 2.521,0.24 10 false Heated Oxygen Sensor Output Voltage 0.385,3.865 1.646,4.094 1.26,0.229 10 false Higher than 0.55 V 0.792,4.25 1.625,4.49 0.833,0.24 10 false Below 0.4 V

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.


d.

Idle the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.


f.

Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.

Standard:
GTS Display Specified Condition
Control the Injection Volume (+12.5%) Air fuel ratio sensor output voltage is below 3.1 V
Control the Injection Volume (-12.5%) Air fuel ratio sensor output voltage is higher than 3.4 V


Result
Result Proceed to
Abnormal A
Normal B

HINT:
·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.





A

40.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR POWER SOURCE)

B

42.READ FREEZE FRAME DATA
40.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR POWER SOURCE)
a.

Check the harnesses and connectors, referring to DTC P0031 inspection procedure (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>P0031).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

41.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

41.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P2237 inspection procedure (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>P2237).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

42.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

42.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Proceed to
Initial Engine Coolant Temp, Ambient Temperature, Initial Intake Air Temp Difference in temperature between each item is less than 10°C*1 A
Difference in temperature between each item is 10°C or more*2 B

HINT:
·

*1: A long time had elapsed after stopping the engine.

·

*2: A long time had not elapsed after stopping the engine.





A

43.READ FREEZE FRAME DATA

B

45.READ FREEZE FRAME DATA
43.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

A217929E01
0.467,0.856 2.887,1.519 2.420,0.663 10 Engine Coolant Temperature Increase after Engine Start (Engine Coolant Temperature - Engine Coolant Temperature at Engine Start) 3.423,0.037 3.718,0.234 0.295,0.198 10 (°C) 5.609,2.116 6.223,2.286 0.614,0.170 10 (Minutes) 5.16,1.69 5.316,1.846 0.156,0.156 10 A 4.964,0.779 5.120,0.935 0.156,0.156 10 C 3.891,0.493 4.047,0.649 0.156,0.156 10 B 3.563,2.39 5.573,2.546 2.010,0.156 10 Time Elapsed after Engine Start

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time Range A
·

Engine coolant temperature sensor

·

Thermostat


A
Range B Engine coolant temperature sensor B
Range C - C

HINT:

This step is not directly related to engine stall.




A

44.INSPECT THERMOSTAT

B

46.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

C

74.CHECK FUEL SYSTEM
44.INSPECT THERMOSTAT
HINT:

For the thermostat inspection, refer to the following procedures (See page Engine / Hybrid System>1UR-FE (COOLING)>THERMOSTAT>INSPECTION).


Result
Result Proceed to
Abnormal A
Normal B


A

B

46.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
45.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Coolant Temp 120°C or higher Engine coolant temperature sensor A
Coolant Temp, Ambient Temperature Engine coolant temperature is lower than outside temperature by 15°C or more Engine coolant temperature sensor
Both freeze frame data items listed above Values are other than above - B



A

46.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

77.CLEAR DTC
46.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
HINT:

For the engine coolant temperature sensor inspection, refer to the following procedures (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).


Result
Result Proceed to
Normal A
Abnormal B


A

47.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE)

B

47.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE)
a.

Disconnect the ECM connector.


b.

Disconnect the engine coolant temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C18-2 - C46-76 (THW) Always Below 1 Ω
C18-1 - C46-98 (E2) Always Below 1 Ω
C18-2 or C46-76 (THW) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C18-2 - C45-76 (THW) Always Below 1 Ω
C18-1 - C45-98 (E2) Always Below 1 Ω
C18-2 or C45-76 (THW) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

48.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).



OK

49.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

49.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC
P1605
Result Suspected Area Proceed to
Total of ISC Learning Value and ISC Feedback Value Below 80% of the current value of the vehicle Intake air volume insufficient A
80% or more of the current value of the vehicle B



A

50.CHECK INTAKE SYSTEM

B

52.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)
50.CHECK INTAKE SYSTEM
a.

Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.] (See page Engine / Hybrid System>1UR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

HINT:
·

If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.

·

If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.

OK:

There is no air leakage.






OK

51.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE INTAKE SYSTEM

51.CHECK INTAKE SYSTEM
a.

Check the intake system.

·

Inspect the mass air flow meter.

·

Check the PCV hose.

·

Inspect the PCV valve.

·

Inspect the purge VSV.

Result
Result Proceed to
Abnormal A
Normal B




A

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

NG

56.READ FREEZE FRAME DATA
52.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)
a.

Connect the GTS to the DLC3.


b.

Turn the GTS on.


c.

Warm up the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank1) or Control the VVT Linear (Bank2).

HINT:

When performing the Active Test, make sure the A/C is on and the shift lever is in N or P.



e.

Check the engine speed while operating the camshaft timing oil control valve using the GTS.

OK:
GTS Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.

·

If the camshaft timing oil control valve is stuck ON, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.





OK

53.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

53.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Check the harnesses and connectors, referring to DTC P0010 inspection procedure (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>P0010).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

54.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

54.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR)
a.

Connect the GTS to the DLC3.


b.

Turn the GTS on.


c.

Warm up the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank1) or Control the VVT Exhaust Linear (Bank2).

HINT:

When performing the Active Test, make sure the A/C is on and the shift lever is in N or P.



e.

Check the engine speed while operating the camshaft timing oil control valve using the GTS.

OK:
GTS Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.

·

If the camshaft timing oil control valve is stuck ON, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.





OK

55.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE)

NG

70.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)
55.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE)
a.

Check the harnesses and connectors, referring to DTC P0013 inspection procedure (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>P0013).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

56.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

56.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
IGN Advance Knock Correct Learn Value
Differs from the current value of the vehicle by 10deg(CA) or more Less than 3deg(CA)
·

Engine coolant temperature sensor

·

Mass air flow meter assembly

·

Knock sensor


A
3deg(CA) or more - B
Differs from the current value of the vehicle by less than 10deg(CA) - -



A

57.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

57.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.


OK

58.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE)

NG

58.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE)
a.

Disconnect the ECM connector.


b.

Disconnect the engine coolant temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C18-2 - C46-76 (THW) Always Below 1 Ω
C18-1 - C46-98 (E2) Always Below 1 Ω
C18-2 or C46-76 (THW) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C18-2 - C45-76 (THW) Always Below 1 Ω
C18-1 - C45-98 (E2) Always Below 1 Ω
C18-2 or C45-76 (THW) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

59.INSPECT MASS AIR FLOW METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

59.INSPECT MASS AIR FLOW METER ASSEMBLY
a.

Inspect the mass air flow meter assembly (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION).

HINT:

If the intake air temperature sent to the ECM is higher than the standard due to the mass air flow meter (intake air temperature sensor) malfunctioning, the ignition timing may become delayed.




OK

60.READ VALUE USING GTS

NG

60.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the GTS, read the value of IGN Advance and Knock Correct Learn Value in the Data List.

Result
Freeze Frame Data Item for DTC P1605 Proceed to
IGN Advance Knock Correct Learn Value
Differs from the current value of the vehicle by 10° or more Less than 3° A
3° or more B
Differs from the current value of the vehicle by less than 10° -

HINT:

If the results of the checks performed in steps 56 to 64 were all normal and the sum of ISC Feedback Value and ISC Learning Value in the Data List is 120% of the normal value or more, check for carbon deposits in the throttle body assembly. If there are carbon deposits, clean them off to finish the troubleshooting procedure.




A

CHECK KNOCK SENSOR CIRCUIT

B

END

61.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)
U163282E01
0.159,0.133 0.472,0.317 0.313,0.184 10 *a 0.281,1.248 0.502,1.413 0.221,0.165 10 a1 0.79,1.248 1.006,1.413 0.216,0.165 10 a5 0.281,1.591 0.502,1.757 0.221,0.165 10 a2 0.79,1.591 1.006,1.757 0.216,0.165 10 a6 0.281,1.935 0.502,2.100 0.221,0.165 10 a3 0.79,1.935 1.006,2.100 0.216,0.165 10 a7 0.281,2.279 0.502,2.444 0.221,0.165 10 a4 0.79,2.279 1.006,2.444 0.216,0.165 10 a8

a.

Disconnect the fuel injector connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Cylinder Tester Connection Switch Condition Specified Condition
No. 1 a5-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 2 a1-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 3 a6-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 4 a2-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 5 a7-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 6 a3-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 7 a8-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 8 a4-2 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Fuel Injector Assembly)

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. There may be an electrical malfunction in the wiring shared by all the cylinders.





OK

62.CHECK IGNITION SYSTEM

NG

CHECK FUEL INJECTOR ASSEMBLY

62.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).



OK

63.CHECK FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

63.CHECK FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
A/C Signal Air Conditioner FB Val Power Steering Signal
A/C Signal display does not change from OFF Value displayed for Air Conditioner FB Val does not increase Does not change from OFF Power steering system A
Changes from OFF to ON -
A/C Signal display changes from OFF to ON Value displayed for Air Conditioner FB Val increases Changes from OFF to ON Power steering system
Does not change from OFF A/C system B

HINT:
·

*1: Check not only the on/off state of the air conditioner, but also the change in air conditioner load.

·

The normal value for the ISC learned value is engine displacement (liters) x 0.9.

·

Even if the results are normal, the power steering system may have been malfunctioning. Continue this inspection procedure until step 47, and if there are no problems with other parts, inspect the power steering system (refer to step 55).





A

64.CHECK FREEZE FRAME DATA

B

64.CHECK FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
Electrical Load Signal or Electric Load Feedback Val Electric Load Feedback Val Difference between Engine Speed and Turbine Speed Vehicle Speed
Electrical Load Signal display changes from OFF to ON*1, or value displayed for Electric Load Feedback Val increases*1 Value displayed for Electric Load Val changes - - Electrical load signal circuit C
Value displayed for Electric Load Val does not change At least 1 of the 5 sets of freeze frame data is less than 100 rpm Less than 30 km/h A/T system B
30 km/h or more - A
All 5 sets of freeze frame data are 100 rpm or more - - A
Electrical Load Signal display does not change from OFF, or value displayed for Electric Load Feedback Val does not increase - At least 1 of the 5 sets of freeze frame data is less than 100 rpm Less than 30 km/h A/T system B
30 km/h or more - A
All 5 sets of freeze frame data are 100 rpm or more - - A

HINT:
·

*1: If the Electrical Load Signal display changes from OFF to ON, or the "Electric Load Feedback Val" increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.

·

The normal value for the ISC learned value is engine displacement (liters) x 0.9.

·

Even if the results are normal, the electrical load signal system and/or A/T system may have been malfunctioning. Continue this inspection procedure until step 47, and if there are no problems with other parts, inspect the electrical load system and/or A/T system (refer to step 55).





A

65.CHECK FREEZE FRAME DATA

B

CHECK AUTOMATIC TRANSMISSION SYSTEM

C

65.CHECK FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
P Position or N Position Park/Neutral Position Switch
P and N position are both OFF in at least one data set In D or R, NSW is ON Park/neutral position switch assembly A
In D or R, NSW is OFF A/T system B
All 5 sets of freeze frame data are ON - - C

HINT:

Even if the results are normal, the park/neutral position switch and/or A/T system may have been malfunctioning. If there are no problems with other parts, inspect the park/neutral position switch and/or A/T system (refer to step 55).




A

B

CHECK AUTOMATIC TRANSMISSION SYSTEM

C

66.CHECK FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Result Suspected Area Proceed to
Throttle Sensor Position, Calculate Load Calculate Load decreases while Throttle Sensor Position increases Mass air flow meter assembly A
Calculate Load does not decrease while Throttle Sensor Position increases - B



A

67.CHECK MASS AIR FLOW METER ASSEMBLY

B

70.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)
67.CHECK MASS AIR FLOW METER ASSEMBLY
a.

Remove the mass air flow meter assembly.


b.

Check for foreign matter in the airflow passage of the mass air flow meter.

Result
Result Proceed to
Visible foreign matter is present A
Visible foreign matter is not present B


c.

Install the mass air flow meter.

HINT:

Even if the results are normal, the mass air flow meter may have been malfunctioning. Continue this inspection procedure until step 54, and if there are no problems with other parts, replace the mass air flow meter assembly (refer to step 55).




A

68.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)

B

68.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)
a.

Check the harnesses and connectors, referring to DTC P0102 inspection procedure (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>P0102).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

69.PERFORM DRIVE TEST

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

69.PERFORM DRIVE TEST
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the GTS, read the value of Calculate Load in the Data List.

Standard
Data List Specified Condition
Calculate Load 90 to 110% of the current value of the vehicle



OK

70.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)

NG

70.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)
U163282E01
0.159,0.133 0.472,0.317 0.313,0.184 10 *a 0.281,1.248 0.502,1.413 0.221,0.165 10 a1 0.79,1.248 1.006,1.413 0.216,0.165 10 a5 0.281,1.591 0.502,1.757 0.221,0.165 10 a2 0.79,1.591 1.006,1.757 0.216,0.165 10 a6 0.281,1.935 0.502,2.100 0.221,0.165 10 a3 0.79,1.935 1.006,2.100 0.216,0.165 10 a7 0.281,2.279 0.502,2.444 0.221,0.165 10 a4 0.79,2.279 1.006,2.444 0.216,0.165 10 a8

a.

Disconnect the fuel injector connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Cylinder Tester Connection Switch Condition Specified Condition
No. 1 a5-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 2 a1-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 3 a6-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 4 a2-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 5 a7-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 6 a3-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 7 a8-2 - Body ground Engine switch on (IG) 11 to 14 V
No. 8 a4-2 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Fuel Injector Assembly)

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. There may be an electrical malfunction in the wiring shared by all the cylinders.





OK

71.CHECK IGNITION SYSTEM

NG

CHECK FUEL INJECTOR ASSEMBLY

71.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).



OK

72.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

72.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Duty.


e.

When performing the Active Test, check for an operating sound from the fuel pump.

Standard
Control the Fuel Pump Duty Specified Condition
25 or 80% Operating sound heard
OFF Operating sound not heard

Result
Result Proceed to
Abnormal A
Normal B

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.

·

If the fuel pump operating noise is abnormal, proceed to step 77.





A

73.INSPECT FUEL PUMP

B

74.CHECK FUEL SYSTEM
73.INSPECT FUEL PUMP
a.


OK

NG

74.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check the fuel leaks.

·

Check the fuel pressure.

·

Check the fuel pressure (for high pressure).

HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



Result
Result Proceed to
Abnormal A
Normal B



A

75.CHECK FUEL SYSTEM

B

75.CHECK FUEL SYSTEM
a.

Check for foreign matter, such as iron particles, around the fuel pump, fuel pump filter and inside the fuel tank, and for signs that the fuel pump was stuck.

Result:
Result Proceed to
There is foreign matter or signs that fuel pump was stuck A
There is no foreign matter and no signs that fuel pump was stuck B


HINT:

If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.




A

76.CHECK FUEL SYSTEM

B

REPAIR OR REPLACE FUEL SYSTEM

76.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check the fuel leaks.

·

Check the fuel pressure.

·

Check the fuel pressure (for high pressure).

HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).





OK

END

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

77.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).




NEXT

END