Home › Engine / Hybrid System › 1UR-FE (LUBRICATION) › OIL PUMP › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052797 1UR-FE LUBRICATION _0255211 OIL PUMP A

1UR-FE LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 16322 1.INSTALL WATER INLET PIPE

a.

Apply soapy water to 2 new O-rings and install them to the water inlet pipe.


b.

Install the water inlet pipe to the No. 1 heat exchanger cover.


Hide 11302 2.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new gasket.


b.

Install the gasket to the cylinder block.


c.

Apply a light coat of engine oil to a new O-ring.


d.

Install the O-ring to the oil pan.


e.

Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.

A386005E01
1.333,1.99 1.479,2.115 1.479,2.115 1.615,2.115 false 4.354,1.927 4.198,1.948 4.198,1.948 4.042,1.948 false 0.781,3.844 1.396,4.042 0.615,0.198 10 false : *1 0.792,4.146 1.406,4.344 0.615,0.198 10 false : *2 0.781,4.427 1.396,4.625 0.615,0.198 10 false : *3 0.896,3.094 1.135,3.313 0.24,0.219 10 false *c 0.719,2.406 0.958,2.625 0.24,0.219 10 false *b 0.979,1.167 1.198,1.333 0.219,0.167 10 true *c 2.479,0.604 2.719,0.823 0.24,0.219 10 false *a 2.771,0.615 3.01,0.833 0.24,0.219 10 false *a 1.667,2.031 2.073,2.198 0.406,0.167 10 true B - B 2.115,1.76 2.333,1.927 0.219,0.167 10 true *d 3.156,1.781 3.375,1.948 0.219,0.167 10 true *c 3.625,1.844 4.031,2.01 0.406,0.167 10 true A - A 4.813,2.292 5.052,2.51 0.24,0.219 10 false *b 4.021,3.073 4.26,3.292 0.24,0.219 10 false *c 4.792,3.115 5.031,3.333 0.24,0.219 10 false *e 6.375,3.125 6.615,3.344 0.24,0.219 10 false *e 4.833,4.323 5.24,4.49 0.406,0.167 10 false A - A 6.26,4.344 6.667,4.51 0.406,0.167 10 false B - B

Text in Illustration
*1 Continuous Line Area *2 Dashed Line Area
*3 Diagonal Line Area - -
*a 20.0 mm (0.787 in.) *b 26.0 mm (1.02 in.)
*c 16.0 mm (0.630 in.) *d 18.0 mm (0.709 in.)
*e 7.0 mm (0.276 in.) - -

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


A229741E04
2.396,1.948 2.26,1.948 2.26,1.948 1.896,2.083 false 0.979,0.01 1.146,0.156 0.167,0.146 10 false *1 2.813,1.146 3.01,1.344 0.198,0.198 10 false *2 0.396,1.125 1.115,1.292 0.719,0.167 10 false 2.0 (0.079) 0.396,0.854 1.104,1.021 0.708,0.167 10 false 3.2 (0.126) 0.385,0.156 1.094,0.323 0.708,0.167 10 false 6.0 (0.236) 1.24,1.25 1.469,1.417 0.229,0.167 10 false 8.0 0.396,0.625 1.125,0.792 0.729,0.167 10 false 4.0 (0.157) 2.313,1.25 2.615,1.406 0.302,0.156 10 false 12.0 1.74,1.25 2.052,1.427 0.313,0.177 10 false 10.0 2.417,1.865 2.604,2.021 0.188,0.156 10 false *4 1.271,1.771 1.448,1.948 0.177,0.177 10 false *3 1.063,1.417 1.542,1.594 0.479,0.177 10 false (0.315) 1.667,1.417 2.146,1.604 0.479,0.188 10 false (0.394) 2.25,1.417 2.74,1.594 0.49,0.177 10 false (0.472)

Application Specification:
Area Seal Packing Diameter Application Position from Inside Edge of Cover
Continuous line area 3.0 to 4.0 mm (0.118 to 0.157 in.) 2.5 mm (0.0984 in.)
Dashed line area 6.4 mm (0.252 in.) or more, or within OK area shown in illustration 7.0 mm (0.276 in.)
Diagonal line area 3.0 to 4.0 mm (0.118 to 0.157 in.) 5.5 mm (0.217 in.)



Text in Illustration
*1 Seal Packing Thickness mm (in.)
*2 Seal Packing Width mm (in.)
*3 Thickness
*4 Width
V100155

OK Area

NOTICE:
·

When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.

·

Install the chain cover within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.




f.
A210031

Align the oil pump drive rotor spline and crankshaft as shown in the illustration and install the chain cover.


g.
U163317E02
2.698,0.823 2.844,1 0.146,0.177 10 false B 1.802,0.469 1.958,0.625 0.156,0.156 10 false *1 2.208,0.188 2.354,0.365 0.146,0.177 10 false A 1.802,1.99 1.948,2.167 0.146,0.177 10 true E 2.833,1.948 2.979,2.125 0.146,0.177 10 false D 1.26,1.708 1.406,1.885 0.146,0.177 10 false C 2.563,2.708 2.708,2.885 0.146,0.177 10 false A 2.208,3.01 2.354,3.188 0.146,0.177 10 false A 1.792,3.063 1.938,3.24 0.146,0.177 10 false A 1.458,3.063 1.604,3.24 0.146,0.177 10 false A 1.052,3 1.198,3.177 0.146,0.177 10 false A 0.198,1.865 0.344,2.042 0.146,0.177 10 false A 0.229,1 0.375,1.177 0.146,0.177 10 false A 1.365,0.375 1.51,0.552 0.146,0.177 10 false A 1.083,0.219 1.229,0.396 0.146,0.177 10 false A 3.125,1.854 3.271,2.031 0.146,0.177 10 false A 3.104,1.021 3.25,1.198 0.146,0.177 10 false A 0.823,2.604 0.969,2.781 0.146,0.177 10 false B 0.75,2.344 0.896,2.521 0.146,0.177 10 false B 2.625,2.417 2.771,2.594 0.146,0.177 10 false B 2.208,1.448 2.354,1.625 0.146,0.177 10 false D 2.375,1.323 2.521,1.5 0.146,0.177 10 true D 1.01,1.323 1.156,1.5 0.146,0.177 10 true E 0.406,2.01 0.552,2.188 0.146,0.177 10 false F 1.656,0.698 1.802,0.875 0.146,0.177 10 false F 0.854,1.042 1,1.219 0.146,0.177 10 true F 0.615,2 0.76,2.177 0.146,0.177 10 false D

Temporarily install the 26 bolts and nut.

Standard Bolt:
Item Length Thread Diameter
Bolt A 25 mm (0.984 in.) 8 mm (0.315 in.)
Bolt B 55 mm (2.17 in.) 8 mm (0.315 in.)
Bolt C 70 mm (2.76 in.) 8 mm (0.315 in.)
Bolt D 35 mm (1.38 in.) 10 mm (0.394 in.)
Bolt E 55 mm (2.17 in.) 10 mm (0.394 in.)
Bolt F 80 mm (3.15 in.) 10 mm (0.394 in.)


Text in Illustration
*1 Nut

NOTICE:

Make sure that there is no oil on the bolt threads.



h.
A214837E04
2.135,1.146 2.25,1.313 0.115,0.167 10 true 1 0.896,1.656 1.01,1.823 0.115,0.167 10 false 2 0.927,0.688 1.042,0.854 0.115,0.167 10 true 3

Tighten the 3 bolts in several steps in the sequence shown in the illustration.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


i.
A229735

Temporarily install the fan bracket with the 5 bolts.

Standard Bolt:
Item Length Thread Diameter
Bolt A 70 mm (2.76 in.) 8 mm (0.315 in.)
Bolt B 80 mm (3.15 in.) 10 mm (0.394 in.)


Text in Illustration
V100135

Bolt A
V100136

Bolt B


j.
A229736

Temporarily install the belt tensioner with the bolt and 6 mm hexagon bolt.

Text in Illustration
V100135

Bolt
V100136

6 mm Hexagon Bolt


k.
U115393E01
1.635,0.042 1.76,0.219 0.125,0.177 10 false 4 2.281,0.719 2.406,0.896 0.125,0.177 10 false 5 2.865,1.385 2.99,1.563 0.125,0.177 10 false 6 2.99,1.146 3.115,1.323 0.125,0.177 10 false 7 2.438,0.292 2.563,0.469 0.125,0.177 10 true 8 1.375,0 1.5,0.177 0.125,0.177 10 false 9 0.177,1.063 0.365,1.24 0.188,0.177 10 false 10 2.646,1.552 2.833,1.729 0.188,0.177 10 false 11

Tighten the 8 bolts labeled 4 to 11 in several steps in the sequence shown in the illustration.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


l.
A214839E04
0.635,1.906 0.833,2.083 0.198,0.177 10 false 12 1.75,0.677 1.948,0.854 0.198,0.177 10 false 13 0.646,2.104 0.844,2.281 0.198,0.177 10 false 19 2.542,2.677 2.74,2.854 0.198,0.177 10 false 18 2.625,2.396 2.823,2.573 0.198,0.177 10 false 17 1.531,2.031 1.729,2.208 0.198,0.177 10 true 16 1.073,1.552 1.271,1.729 0.198,0.177 10 true 15 2.063,1.75 2.26,1.927 0.198,0.177 10 true 14 0.698,2.323 0.896,2.5 0.198,0.177 10 false 20 1.458,0.458 1.656,0.635 0.198,0.177 10 false 28 0.271,1.021 0.469,1.198 0.198,0.177 10 false 27 0.323,1.906 0.521,2.083 0.198,0.177 10 false 26 2.177,3.042 2.375,3.219 0.198,0.177 10 false 25 1.448,3.073 1.646,3.25 0.198,0.177 10 false 22 1.781,3.073 1.979,3.25 0.198,0.177 10 false 24 1.031,3.021 1.229,3.198 0.198,0.177 10 false 23 0.792,2.594 0.99,2.771 0.198,0.177 10 false 21 2.448,1.615 2.646,1.792 0.198,0.177 10 true 30 1.063,0.219 1.26,0.396 0.198,0.177 10 false 29 3.031,1.031 3.229,1.208 0.198,0.177 10 false 34 3.219,1.771 3.417,1.948 0.198,0.177 10 false 33 2.198,0.188 2.396,0.365 0.198,0.177 10 false 32 1.917,0.427 2.115,0.604 0.198,0.177 10 false 31

Tighten the 22 bolts and nut labeled 12 to 34 in several steps in the sequence shown in the illustration.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)

NOTICE:
·

Do not start the engine for at least 2 hours after the installation.

·
A210033

After the installation, if the seal packing has seeped out at the areas labeled A shown in the illustration, wipe it off.



Text in Illustration
V100144

Labeled A


m.

Check the torque of each bolt and nut again.


Hide 11202 4.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.

Install 5 new gaskets to the camshaft bearing caps (No. 2, No. 3).


b.

Install a new cylinder head cover gasket LH to the cylinder head cover sub-assembly LH.

NOTICE:

Remove any oil from the contact surface.



c.
A229737

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Text in Illustration
V100143

Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




d.

Install a new seal washer to the bolt.


e.
A229739E03
1.292,0.094 1.396,0.26 0.104,0.167 10 false 1 1.688,1.906 1.792,2.073 0.104,0.167 10 true 2 1.844,0.094 1.948,0.26 0.104,0.167 10 false 3 1.156,1.896 1.26,2.063 0.104,0.167 10 true 4 0.958,0 1.063,0.167 0.104,0.167 10 false 5 2.208,1.896 2.313,2.063 0.104,0.167 10 true 6 2.542,0.104 2.646,0.271 0.104,0.167 10 false 7 0.198,1.854 0.302,2.021 0.104,0.167 10 false 8 0.042,0.052 0.146,0.219 0.104,0.167 10 false 9 0.031,1.323 0.219,1.479 0.188,0.156 10 false 10 2.823,1.813 3.01,1.969 0.188,0.156 10 true 11 3.219,0.135 3.406,0.292 0.188,0.156 10 false 12 3.229,1.5 3.417,1.656 0.188,0.156 10 false 13 1.885,1.49 2.073,1.646 0.188,0.156 10 true 14

Temporarily install the cylinder head cover sub-assembly LH with the 14 bolts. Tighten the bolts uniformly in several steps.

Torque:
for bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for bolt B : 12 N*m (122 kgf*cm, 9 ft.*lbf)

Standard Bolt:
Item Length Thread Diameter
Bolt A 70 mm (2.76 in.) 8 mm (0.315 in.)
Bolt B 25 mm (0.984 in.) 6 mm (0.236 in.)


Text in Illustration
V100135

Bolt A
V100136

Bolt B

NOTICE:

Do not start the engine for at least 2 hours after the installation.



Hide 11201 5.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH

a.

Install 5 new gaskets to the camshaft bearing caps. (No. 1, No. 3).


b.

Install a new cylinder head cover gasket RH to the cylinder head cover sub-assembly RH.

NOTICE:

Remove any oil from the contact surface.



c.
A229738

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Text in Illustration
V100143

Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




d.

Install a new seal washer to the bolt.


e.
A229740E03
2.063,0.063 2.167,0.229 0.104,0.167 10 true 1 1.688,1.854 1.792,2.021 0.104,0.167 10 true 2 1.406,0.052 1.51,0.219 0.104,0.167 10 true 3 2.208,1.854 2.313,2.021 0.104,0.167 10 true 4 2.615,0 2.719,0.167 0.104,0.167 10 true 5 1.167,1.854 1.271,2.021 0.104,0.167 10 true 6 0.865,0.063 0.969,0.229 0.104,0.167 10 true 7 3.146,1.802 3.25,1.969 0.104,0.167 10 false 8 3.281,0.021 3.385,0.188 0.104,0.167 10 false 9 3.208,1.281 3.396,1.438 0.188,0.156 10 false 10 0.594,1.875 0.781,2.031 0.188,0.156 10 true 11 0.063,0.073 0.25,0.229 0.188,0.156 10 false 12 0.031,1.458 0.219,1.615 0.188,0.156 10 false 13 1.375,1.438 1.563,1.594 0.188,0.156 10 true 14

Temporarily install the cylinder head cover sub-assembly RH with the 14 bolts. Tighten the bolts uniformly in several steps.

Torque:
for bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for bolt B : 12 N*m (122 kgf*cm, 9 ft.*lbf)

Standard Bolt:
Item Length Thread Diameter
Bolt A 70 mm (2.76 in.) 8 mm (0.315 in.)
Bolt B 25 mm (0.984 in.) 6 mm (0.236 in.)


Text in Illustration
V100135

Bolt A
V100136

Bolt B

NOTICE:

Do not start the engine for at least 2 hours after the installation.



Hide 13471 7.INSTALL CRANKSHAFT PULLEY

a.

Align the key groove of the pulley with the pulley set key, and slide on the pulley to install it.


b.
A164230E05
1.792,1.458 2.073,1.854 2.073,1.854 2.021,1.365 true 0.167,0.542 0.354,0.729 0.188,0.188 10 false *a 1.948,1.896 2.281,2.063 0.333,0.167 10 false SST

Using SST, install the pulley set bolt.

SST
09213-70011  
09330-00021  

Torque:
300 N*m (3059 kgf*cm, 221 ft.*lbf)

Text in Illustration
*a Hold
V100135

Turn


Hide 16603 8.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.

Install the No. 1 idler pulley with the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16355 10.INSTALL FRONT WATER BY-PASS JOINT

a.

Install 2 new gaskets and the water by-pass joint with the 4 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16206 12.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Install the water by-pass pipe sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 2 water by-pass hose from the front water by-pass joint.


Hide 16281F 13.CONNECT NO. 5 WATER BY-PASS HOSE

Hide 16278K 14.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16261G 15.INSTALL NO. 1 WATER BY-PASS HOSE

Hide 16261L 16.CONNECT WATER BY-PASS HOSE

Hide 16268 17.INSTALL NO. 1 WATER BY-PASS PIPE

a.

Connect the No. 1 water by-pass pipe with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Connect the heater water hose.


Hide 17363Q 18.INSTALL NO. 3 AIR TUBE (w/ Secondary Air Injection System)

a.

Install a new gasket to the No. 3 air tube.


b.
A272656E01
2.069,0.805 2.224,0.952 0.155,0.147 10 *1 2.065,1.59 2.220,1.737 0.155,0.147 10 *3 2.481,1.189 2.637,1.337 0.155,0.147 10 *2 2.278,1.371 2.419,1.275 2.419,1.275 2.474,1.275 false

Install the No. 3 air tube with the 2 stud bolts, 2 nuts and bolt.

Torque:
for bolt and nut : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for stud bolt : 5.0 N*m (51 kgf*cm, 44 in.*lbf)

Text in Illustration
*1 No. 3 Air Tube
*2 Claw
*3 Exhaust Manifold

NOTICE:

Make sure the claws of the gasket are not caught between the No. 3 air tube and exhaust manifold.



Hide 17364A 19.INSTALL NO. 4 AIR TUBE (w/ Secondary Air Injection System)

a.

Install a new gasket to the No. 4 air tube.


b.
A272655E02
1.208,0.531 1.313,0.271 1.313,0.271 1.385,0.271 false 1.625,0.594 1.781,0.75 0.156,0.156 10 false *1 1.396,0.188 1.552,0.344 0.156,0.156 10 false *2 0.802,0.583 0.958,0.74 0.156,0.156 10 false *3

Install the No. 4 air tube with the 2 stud bolts, 2 nuts and bolt.

Torque:
for bolt and nut : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for stud bolt : 5.0 N*m (51 kgf*cm, 44 in.*lbf)

Text in Illustration
*1 No. 4 Air Tube
*2 Claw
*3 Exhaust Manifold

NOTICE:

Make sure the claws of the gasket are not caught between the No. 4 air tube and exhaust manifold.



c.

Install the wire harness clamp bracket with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 77259E 20.INSTALL FUEL HOSE


b.

Install the fuel pipe clamp.


c.

Connect the 2 clamps.


Hide 23902 21.INSTALL FUEL TUBE SUB-ASSEMBLY


b.

Install the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 44310 26.CONNECT VANE PUMP ASSEMBLY

HINT:

Before performing the following procedures, move the spacer until the vane pump can be installed.


A229744

Text in Illustration
V100144

Spacer

a.

Connect the vane pump to the timing chain cover with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 27.CONNECT POWER STEERING OIL PRESSURE SWITCH CONNECTOR

Hide 83520 31.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 33.CONNECT ENGINE WIRE

a.

Connect the clamp and engine wire with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

for Engine Room RH Side:

i.

Connect the 6 clamps.


ii.

Connect the noise filter connector.


iii.

Connect the injector connector.


iv.

Connect the 2 VVT sensor connectors.


v.

Connect the 4 ignition coil connectors.


vi.

Connect the 2 camshaft timing oil control valve connectors.



c.

for Engine Room LH Side:

i.

Install the ground wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


ii.

Connect the 8 clamps.


iii.

Connect the noise filter connector.


iv.

Connect the engine coolant temperature sensor connector.


v.

Connect the camshaft position sensor connector.


vi.

Connect the 2 VVT sensor connectors.


vii.

Connect the 4 ignition coil connectors.


viii.

Connect the 2 camshaft timing oil control valve connectors.


ix.

Connect the injector connector.



Hide 17361 34.INSTALL AIR TUBE (w/ Secondary Air Injection System)

a.

Install the air tube with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 3 air injection system hose.


c.

Attach the wire harness clamp.


Hide 25710 35.INSTALL AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System)

Hide 88320 36.CONNECT COOLER COMPRESSOR ASSEMBLY

a.
A178491E02
3.101,1.544 3.212,1.698 0.111,0.154 10 1 3.169,1.847 3.289,1.999 0.119,0.152 10 2 3.295,1.349 3.411,1.512 0.115,0.163 10 3 2.615,1.92 2.724,2.074 0.109,0.154 10 4

Install the cooler compressor with the stud bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install the 3 bolts and nut.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)

NOTICE:

Tighten the bolts and nut in the order shown in the illustration to install the cooler compressor.



Hide 16400 38.INSTALL RADIATOR ASSEMBLY

Hide 53782 40.INSTALL FRONT FENDER APRON TRIM PACKING A

Hide 43.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).