Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › CAMSHAFT › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052778 1GR-FE ENGINE MECHANICAL _0255062 CAMSHAFT A

1GR-FE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 16711 1.REMOVE FAN SHROUD

Hide 17129 2.REMOVE INTAKE AIR SURGE TANK

Hide 17361 3.REMOVE AIR TUBE (w/ Secondary Air Injection System)

Hide 17362 4.REMOVE NO. 2 AIR TUBE (w/ Secondary Air Injection System)

Hide 25701B 5.REMOVE NO. 1 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

Hide 25702B 6.REMOVE NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

Hide 44310 8.DISCONNECT VANE PUMP ASSEMBLY

Hide 16604 9.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 17168 10.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 11452 12.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 16206 13.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 11202 17.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 11201 18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11324 19.REMOVE TIMING CHAIN COVER PLATE

a.
A224737

Remove the 4 bolts, timing chain cover plate and gasket.


Hide 20.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A072945

Turn the crankshaft pulley and align the notch with the "0" timing mark of the timing chain cover.


b.
A224754E01
0.05,0 0.286,0.194 0.236,0.194 10 *A 0.05,2.41 0.286,2.604 0.236,0.194 10 *B 0.131,1.72 0.299,1.914 0.168,0.194 10 *1 3.086,3.813 3.294,4.007 0.208,0.194 10 *1 0.319,1.802 0.453,1.802 0.453,1.802 0.979,1.45 false 3.065,3.903 2.831,3.903 2.831,3.903 2.279,3.674 false

Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.

Text in Illustration
*A for Bank 2
*B for Bank 1
*1 Paint Mark

HINT:

If the marks are not aligned, turn the crankshaft again to align the marks.



c.

Place paint marks on the timing marks and sprockets of each camshaft timing gear and on the links of the No. 1 chain.

HINT:

Be sure to place the paint marks on 2 links of the chain and on the sprockets of the camshaft timing gears at the locations of the timing marks of the camshaft timing gears.



Hide 13540 21.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A226510E07
2.74,0.177 3.063,0.448 0.323,0.271 10 true 30° 3.104,0.865 3.292,1.031 0.188,0.167 10 false 0°

Turn the crankshaft approximately 30° counterclockwise so that there is some slack in the chain.

HINT:

This prevents the valves and pistons from interfering with each other.



b.
A226547E01
1.531,0.243 1.716,0.405 0.185,0.162 10 *1 0.198,1.669 0.382,1.863 0.184,0.194 10 *2 1.508,0.328 1.357,0.328 1.357,0.328 1.074,0.992 false 0.415,1.752 0.611,1.752 0.611,1.752 1.006,1.116 false

Align the hole in the lever of the tensioner with the hole in the tensioner body as shown in the illustration, and then insert a pin with a diameter of 1.27 mm (0.0500 in.) into the hole.

Text in Illustration
*1 Lever Hole
*2 Tensioner Hole


c.

Turn the crankshaft clockwise and align the notch with the "0" timing mark of the timing chain cover.


d.
A224739

Remove the 2 bolts and chain tensioner.

NOTICE:

Do not drop the No. 1 chain tensioner assembly or bolts into the timing chain cover.



Hide 13506 22.DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 1)

a.
A226507E07
2.771,1.24 3.083,1.542 0.313,0.302 10 true 30°

Turn the crankshaft clockwise until it is in the position shown in the illustration so that there is some slack in the chain between the banks.

CAUTION:

As the camshafts turn suddenly, do not touch the camshafts or camshaft timing gears.


NOTICE:

When turning the crankshaft, engine oil may spray out of the oil holes.



b.
U163351E02
1.094,1.802 1.417,1.802 1.417,1.802 1.563,2.052 false 0.875,1.708 1.188,2.031 0.313,0.323 10 true *a

Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain can be removed easily.

Text in Illustration
*a 5° to 10°

NOTICE:

When turning the crankshaft, engine oil may spray out of the oil holes.



c.
A224759

Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.

CAUTION:

As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.



Hide 23.REMOVE CAMSHAFT BEARING CAP (for Bank 1)

a.
U147630E04
2.802,4.063 3,4.26 0.198,0.198 2.802,4.052 3,4.25 0.198,0.198 3.198,2.646 3.396,2.844 0.198,0.198 3.198,2.646 3.396,2.844 0.198,0.198 0.229,2.875 0.427,3.073 0.198,0.198 0.229,2.875 0.427,3.073 0.198,0.198 0.073,3.75 0.271,3.948 0.198,0.198 0.083,3.75 0.281,3.948 0.198,0.198 2.333,2.844 2.531,3.042 0.198,0.198 2.333,2.844 2.531,3.042 0.198,0.198 2.021,4.094 2.219,4.292 0.198,0.198 2.021,4.094 2.219,4.292 0.198,0.198 0.917,2.792 1.115,2.99 0.198,0.198 0.917,2.813 1.115,3.01 0.198,0.198 1.01,3.823 1.208,4.021 0.198,0.198 1.01,3.823 1.208,4.021 0.198,0.198 0.51,0.531 0.688,0.531 0.688,0.531 1.167,0.969 true 1.531,1.208 2.052,1.208 true 1.667,1.354 1.875,1.354 1.875,1.354 1.875,1.219 true 3,3.229 3.115,3.396 0.115,0.167 10 false 1 2.854,3.833 2.969,4 0.115,0.167 10 false 2 2.865,4.073 2.979,4.24 0.115,0.167 10 false 3 2.917,2.198 3.063,2.365 0.146,0.167 10 false 4 3,2.677 3.115,2.844 0.115,0.167 10 false 5 3.229,2.656 3.365,2.823 0.135,0.167 10 true 6 0.292,3.323 0.406,3.49 0.115,0.167 10 false 7 0.406,3.771 0.521,3.938 0.115,0.167 10 false 8 0.354,2.24 0.469,2.406 0.115,0.167 10 false 9 0.24,2.688 0.417,2.854 0.177,0.167 10 false 10 0.24,2.896 0.417,3.063 0.177,0.167 10 true 11 0.083,3.76 0.26,3.927 0.177,0.167 10 false 12 2.323,3.396 2.5,3.563 0.177,0.167 10 false 13 2.021,3.865 2.198,4.031 0.177,0.167 10 false 14 2.156,2.177 2.333,2.344 0.177,0.167 10 false 15 2.333,2.635 2.51,2.802 0.177,0.167 10 false 16 2.333,2.865 2.51,3.031 0.177,0.167 10 true 17 2.031,4.104 2.208,4.271 0.177,0.167 10 false 18 0.948,3.396 1.125,3.563 0.177,0.167 10 false 19 1.271,3.844 1.448,4.01 0.177,0.167 10 false 20 1.146,2.146 1.323,2.313 0.177,0.167 10 false 21 0.938,2.615 1.115,2.781 0.177,0.167 10 false 22 0.927,2.833 1.104,3 0.177,0.167 10 true 23 1.021,3.844 1.198,4.01 0.177,0.167 10 true 24 0.302,0.448 0.479,0.615 0.177,0.167 10 false *1 0.594,4.115 0.781,4.281 0.188,0.167 10 false *a 0.604,4.406 0.792,4.573 0.188,0.167 10 false *b 2.042,1.104 2.271,1.281 0.229,0.177 10 true *2

Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install bolts and washers for temporary installation of the camshaft housing in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 Bolt
*2 Washer
*a Part Removal
*b Installation of Bolts and Washers for Temporary Installation of Camshaft Housing

NOTICE:
·

Do not install the bearing caps when installing bolts and washers for temporary installation of the camshaft housing.

·

Be sure to follow the numerical order when performing this procedure.

·

Do not allow bolts and washers for temporary installation of the camshaft housing to contact the camshaft.

·

Do not drop bolts and washers for temporary installation of the camshaft housing into the cylinder head.



HINT:
·

Arrange the removed parts so that they can be reinstalled in their original locations.

·

Part number of bolt for temporary installation of camshaft housing: 91551-G0845 (quantity: 8)

·

Part number of washer for temporary installation of camshaft housing: 90201-12028 (quantity: 16)




Hide 13512 24.REMOVE NO. 2 CAMSHAFT

a.
A224761

Remove the bolt of the No. 2 chain tensioner assembly.


b.
A224769

Remove the No. 2 chain tensioner assembly while lifting up the No. 2 camshaft.


c.
A224763

While lifting up the No. 2 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.


Hide 13511 25.REMOVE CAMSHAFT

a.

Lift up the rear of the camshaft so that it is at an angle.


b.
A224767

Remove the chain from the camshaft timing gear and pull out the camshaft and No. 2 chain towards the rear of the vehicle to remove them.

NOTICE:

Do not drop the chain into the gap between the engine and cover.



c.
A224765

Suspend the chain with a string or equivalent.


Hide 13506 26.DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 2)

a.

Turn the crankshaft counterclockwise and align the notch with the "0" timing mark of the timing chain cover.


b.
A224760

Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.

CAUTION:

As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.



Hide 27.REMOVE CAMSHAFT BEARING CAP (for Bank 2)

a.
U147631E04
0.792,4.156 0.99,4.354 0.198,0.198 0.792,4.156 0.99,4.354 0.198,0.198 0.198,2.688 0.396,2.885 0.198,0.198 0.198,2.688 0.396,2.885 0.198,0.198 3.177,2.906 3.375,3.104 0.198,0.198 3.177,2.896 3.375,3.094 0.198,0.198 2.958,4.094 3.156,4.292 0.198,0.198 2.958,4.094 3.156,4.292 0.198,0.198 1.198,2.917 1.396,3.115 0.198,0.198 1.198,2.917 1.396,3.115 0.198,0.198 1.469,4.115 1.667,4.313 0.198,0.198 1.469,4.115 1.667,4.313 0.198,0.198 2.552,2.865 2.75,3.063 0.198,0.198 2.552,2.865 2.75,3.063 0.198,0.198 2.24,4.135 2.438,4.333 0.198,0.198 2.24,4.135 2.438,4.333 0.198,0.198 2.26,1.031 2.896,1.031 true 1.75,1.365 1.583,1.365 1.583,1.365 1.583,1.229 true 1.885,1.229 1.406,1.229 true 0.479,3.396 0.594,3.563 0.115,0.167 10 false 1 0.844,3.927 0.958,4.094 0.115,0.167 10 false 2 0.844,4.177 0.958,4.344 0.115,0.167 10 false 3 0.781,2.167 0.896,2.333 0.115,0.167 10 false 4 0.5,2.708 0.615,2.875 0.115,0.167 10 false 5 0.24,2.698 0.365,2.927 0.125,0.229 10 true 6 3.24,3.365 3.354,3.531 0.115,0.167 10 false 7 3,3.865 3.115,4.031 0.115,0.167 10 false 8 2.958,2.25 3.073,2.417 0.115,0.167 10 false 9 3.167,2.698 3.344,2.865 0.177,0.167 10 false 10 3.188,2.927 3.365,3.094 0.177,0.167 10 false 11 2.958,4.104 3.135,4.271 0.177,0.167 10 true 12 1.24,3.479 1.417,3.646 0.177,0.167 10 false 13 1.469,3.896 1.646,4.063 0.177,0.167 10 false 14 1.448,2.24 1.625,2.406 0.177,0.167 10 false 15 1.208,2.708 1.385,2.875 0.177,0.167 10 false 16 1.208,2.938 1.385,3.104 0.177,0.167 10 true 17 1.479,4.125 1.656,4.292 0.177,0.167 10 false 18 2.552,3.406 2.729,3.573 0.177,0.167 10 false 19 2.24,3.906 2.417,4.073 0.177,0.167 10 false 20 2.365,2.271 2.542,2.438 0.177,0.167 10 false 21 2.552,2.677 2.729,2.844 0.177,0.167 10 false 22 2.563,2.885 2.74,3.052 0.177,0.167 10 true 23 2.26,4.146 2.438,4.313 0.177,0.167 10 false 24 2.938,0.948 3.115,1.146 0.177,0.198 10 false *1 0.438,4.146 0.625,4.313 0.188,0.167 10 false *a 0.448,4.438 0.635,4.604 0.188,0.167 10 false *b 1.104,1.146 1.385,1.406 0.281,0.26 10 true *2

Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install bolts and washers for temporary installation of the camshaft housing in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 Bolt
*2 Washer
*a Part Removal
*b Installation of Bolts and Washers for Temporary Installation of Camshaft Housing

NOTICE:
·

Do not install the bearing caps when installing bolts and washers for temporary installation of the camshaft housing.

·

Be sure to follow the numerical order when performing this procedure.

·

Do not allow bolts and washers for temporary installation of the camshaft housing to contact the camshaft.

·

Do not drop bolts and washers for temporary installation of the camshaft housing into the cylinder head.



HINT:
·

Arrange the removed parts so that they can be reinstalled in their original locations.

·

Part number of bolt for temporary installation of camshaft housing: 91551-G0845 (quantity: 8)

·

Part number of washer for temporary installation of camshaft housing: 90201-12028 (quantity: 16)




Hide 13054 28.REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY

a.
A224762

Remove the bolt of the No. 3 chain tensioner assembly.


b.
A224770

Remove the No. 3 chain tensioner assembly while lifting up the No. 4 camshaft.


c.
A224764

While lifting up the No. 4 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.


Hide 13053 29.REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY

a.
A224768

Lift up the rear of the camshaft so that it is at an angle.


b.

Remove the chain from the camshaft timing gear and pull out the No. 3 camshaft and No. 2 chain towards the rear of the vehicle to remove them.

NOTICE:

Do not drop the chain into the gap between the engine and cover.



c.
A224766

Suspend the chain with a string or equivalent.


Hide 13050 30.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.

Fix the camshaft in place.

NOTICE:

Be careful not to damage the camshaft.



b.
A227959E01
0.351,0.118 0.534,0.297 0.184,0.179 10 *1 2.106,1.754 2.290,1.927 0.184,0.174 10 *1 2.566,0 2.760,0.174 0.193,0.173 10 *2 0.672,1.803 0.874,1.989 0.202,0.186 10 *3 2.064,0.823 2.451,0.089 2.451,0.089 2.549,0.089 false 0.653,1.897 0.506,1.897 0.506,1.897 0.335,1.617 false 0.977,0.855 0.734,0.204 0.734,0.204 0.564,0.204 false 1.384,1.062 1.94,1.845 false 1.261,1.516 1.495,1.846 1.495,1.846 2.088,1.846 false

Remove the flange bolt and camshaft timing gear assembly.

Text in Illustration
*1 Do not remove
*2 Straight Pin
*3 Flange Bolt

NOTICE:
·

Do not remove the other 3 bolts.

·

If planning to reuse the camshaft timing gear, be sure to release the straight pin lock before installing the camshaft timing gear.




Hide 13070A 31.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Fix the camshaft in place.

NOTICE:

Be careful not to damage the camshaft.



b.
A227960E01
2.424,0.069 2.612,0.254 0.188,0.185 10 *2 0.641,1.767 0.838,1.944 0.197,0.178 10 *3 0.18,0.43 0.357,0.613 0.176,0.183 10 *1 1.869,1.719 2.045,1.902 0.176,0.183 10 *1 0.318,1.633 0.484,1.853 0.484,1.853 0.615,1.853 false 0.398,0.517 0.653,0.517 0.653,0.517 0.926,0.821 false 0.851,1.147 0.653,0.517 false 1.226,1.616 1.368,1.805 1.368,1.805 1.843,1.805 false 1.312,1.247 1.74,1.806 false 2.01,0.782 2.248,0.159 2.248,0.159 2.385,0.159 false

Remove the flange bolt and camshaft timing exhaust gear assembly.

Text in Illustration
*1 Do not remove
*2 Straight Pin
*3 Flange Bolt

NOTICE:
·

Be sure not to remove the other 4 bolts.

·

If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.