Home › Suspension › SUSPENSION CONTROL › SUSPENSION CONTROL CYLINDER
RM2660E _53 Suspension _052813 SUSPENSION CONTROL _0255377 SUSPENSION CONTROL CYLINDER A

SUSPENSION CONTROL  SUSPENSION CONTROL CYLINDER  INSTALLATION  


PROCEDURE

Hide 49081 1.INSTALL CENTER SUSPENSION CONTROL CYLINDER SUB-ASSEMBLY

C172671

a.

Install the cylinder to the bracket with the 2 nuts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 489D0 2.INSTALL HEIGHT CONTROL BRACKET WITH CYLINDER ASSEMBLY

C172670

a.

Install the bracket with cylinder with the 2 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 48993 3.CONNECT NO. 3 HEIGHT CONTROL TUBE LH

C174889

a.

Install a new gasket to the No. 3 height control tube, and then connect the height control tube to the control cylinder with the union bolt.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 48984 4.CONNECT NO. 4 HEIGHT CONTROL TUBE

C174888

a.

Install a new gasket to the No. 4 height control tube, and then connect the height control tube to the control cylinder with the union bolt.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 48994F 5.CONNECT NO. 4 HEIGHT CONTROL TUBE LH

C174887

a.

Install a new gasket to the No. 4 height control tube, and then connect the height control tube to the control cylinder with the union bolt.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 48983 6.CONNECT NO. 3 HEIGHT CONTROL TUBE

C174886

a.

Install a new gasket to the No. 3 height control tube, and then connect the height control tube to the control cylinder with the union bolt.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 48940 7.INSTALL NO. 1 HEIGHT CONTROL VALVE ASSEMBLY

Hide 48997 8.CONNECT REAR NO. 4 HEIGHT CONTROL TUBE

Hide 48985 9.INSTALL NO. 5 HEIGHT CONTROL TUBE

Hide 48995E 10.INSTALL NO. 5 HEIGHT CONTROL TUBE LH

Hide 48996D 11.INSTALL NO. 6 HEIGHT CONTROL TUBE LH

Hide 48986 12.INSTALL NO. 6 HEIGHT CONTROL TUBE

Hide 49130F 14.INSTALL SUSPENSION CONTROL PUMP ACCUMULATOR ASSEMBLY

Hide 489D5 19.INSTALL HEIGHT CONTROL UNIT INSULATOR

Hide 17420 20.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.

for 1GR-FE:

Install the center exhaust pipe (See page Engine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION).


b.

for 1UR-FE:

Install the center exhaust pipe (See page Engine / Hybrid System>1UR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION).


c.

for 3UR-FE:

Install the center exhaust pipe (See page Engine / Hybrid System>3UR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION).


d.

for 1VD-FTV:

Install the center exhaust pipe (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE(w/o DPF)>INSTALLATION).


Hide 17430 21.INSTALL TAILPIPE ASSEMBLY

Hide 22.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.