Home › Suspension › REAR SUSPENSION › REAR STABILIZER BAR(w/ KDSS) › 2014.08–2015.08
RM2660E _53 Suspension _052816 REAR SUSPENSION _0255394 REAR STABILIZER BAR(w/ KDSS) A

REAR SUSPENSION  REAR STABILIZER BAR(w/ KDSS)  INSTALLATION  


PROCEDURE

Hide 49189C 1.INSTALL REAR SUSPENSION CONTROL BLEEDER PLUG

a.
C175252

Install the 2 suspension control bleeder plugs to the rear stabilizer control cylinder.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


Hide 48830 2.INSTALL REAR STABILIZER LINK ASSEMBLY

a.
C175236E01
2.146,1.099 2.482,1.275 0.336,0.177 10 Bolt 2.103,1.167 1.811,1.167 false 1.811,1.167 1.195,1.749 false

Install the rear stabilizer link with the bolt and nut.

Torque:
208 N*m (2121 kgf*cm, 153 ft.*lbf)

NOTICE:

Make sure the bolt is facing the correct direction.



Hide 48831 3.INSTALL REAR NO. 2 STABILIZER LINK

a.
C175235

Install the No. 2 rear stabilizer link with the 2 bolts and 2 nuts.

Torque:
97 N*m (989 kgf*cm, 72 ft.*lbf)

NOTICE:

Make sure the bolts are facing the correct direction.



Hide 48885 4.TEMPORARILY INSTALL REAR STABILIZER CONTROL CYLINDER

a.

Temporarily install the rear stabilizer control cylinder to the frame with the bolt.


b.
C357468E01
0.438,0.438 0.438,0.323 0.438,0.323 0.646,0.323 false 0.115,2.219 0.531,1.802 false 2.229,3.042 2.229,2.844 2.229,2.844 2.354,2.292 true 2.948,2.188 3.292,2.188 true 3.281,2.188 3.281,0.24 3.281,0.24 3.042,0.24 false 0.229,1.052 0.5,1.052 0.5,1.052 0.5,1.219 false 0.135,0.448 0.844,0.656 0.708,0.208 10 false Union Bolt 2.083,0.135 3.031,0.615 0.948,0.479 10 true Rear Stabilizer Control Tube 0.208,1.219 0.917,1.427 0.708,0.208 10 false Union Bolt 2.104,3.063 2.531,3.313 0.427,0.25 10 false Bolt

Install the rear stabilizer control tube and 2 new gaskets to the rear stabilizer control cylinder with the 2 union bolts.

Torque:
69 N*m (704 kgf*cm, 51 ft.*lbf)


c.

Install the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 48802 5.INSTALL STABILIZER LINK SUB-ASSEMBLY

a.
C175253E04
1.385,1.25 1.74,1.583 0.354,0.333 10 true Bolt

Install the stabilizer link to the stabilizer bar with the bolt and nut.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)

NOTICE:

Make sure the bolt is facing the correct direction.



b.
C175256E04
0.927,0.333 1.031,0.333 1.031,0.333 1.083,0.677 false 0.792,0.865 0.896,0.865 0.896,0.865 1,1.083 false 2.604,0.26 2.729,0.26 2.729,0.26 2.729,1.188 true 2.198,2.656 2.344,2.656 2.344,2.656 2.531,2.167 false 2.385,1.146 2.49,1.146 2.49,1.146 2.594,1.552 false 0.229,0.781 0.927,0.948 0.698,0.167 10 false Cushion 2.042,0.167 2.615,0.396 0.573,0.229 10 false Retainer 0.354,0.24 0.927,0.469 0.573,0.229 10 false Retainer 1.604,2.573 2.156,2.844 0.552,0.271 10 true Retainer 1.833,1.052 2.344,1.333 0.51,0.281 10 true Cushion

Make sure that all parts are facing as shown in the illustration and install the stabilizer end bracket, retainers and cushions with a new nut.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 48805 6.INSTALL REAR STABILIZER BAR SUB-ASSEMBLY

a.
C357472E01
0.708,1.615 1.146,1.615 1.146,1.615 1.323,1.188 true 0.188,0.677 0.938,0.906 0.75,0.229 10 true Inner Side 0.281,1.521 0.76,1.76 0.479,0.24 10 true Bump

Install the 2 bushes to the outer side of the bush stoppers on the rear stabilizer bar as shown in the illustration.

NOTICE:

Install the stabilizer bush so that the bump is on the inner side of the vehicle.



b.
C175231E04
1.958,4.073 2.396,4.073 true 1.646,1.865 0.865,1.865 true 0.156,1.76 0.938,1.99 0.781,0.229 10 false Protrusion 2.448,3.99 3.177,4.25 0.729,0.26 10 true Protrusion 2.333,1.781 2.667,2.021 0.333,0.24 10 true 1, 3 2.208,0.396 2.594,0.677 0.385,0.281 10 true 2, 4 1.021,4.094 1.365,4.448 0.344,0.354 10 true 1, 3 1.042,2.875 1.375,3.167 0.333,0.292 10 true 2, 4

Install the 2 stabilizer bar brackets with the 4 bolts.

Torque:
58 N*m (591 kgf*cm, 43 ft.*lbf)

NOTICE:
·

Install the stabilizer bar bracket so that the protrusion is on the lower side.

·

Tighten the bolts in 4 steps, in the order shown in the illustration.




c.
C175234

Install the stabilizer end bracket with the 2 bolts.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


d.
C178731E03
0.844,0.135 0.552,0.135 false 0.552,0.135 0.552,0.448 0.552,0.448 1.542,0.448 false 2.552,0.698 2.344,0.698 false 1.24,1.354 1.323,1.354 false 1.156,1.469 1.323,1.469 false 0.896,0.063 2.958,0.281 2.063,0.219 10 false Ball Joint Dust Cover Protector 2.615,0.604 3.24,1.24 0.625,0.635 10 false Stabilizer Link Assembly 0.167,1.385 1.146,1.76 0.979,0.375 10 false Rear Stabilizer Bar

Install the stabilizer link assembly to the ball joint dust cover protector.


e.
C178880

Install the stabilizer bar to the stabilizer link with the nut.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

HINT:
·

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud bolt.

·

If the rear stabilizer control cylinder extends and it is difficult to temporarily install the stabilizer link to the stabilizer bar, raise the stabilizer control arm with a jack and temporarily install the stabilizer link.




Hide 7.BLEED AIR FROM SUSPENSION FLUID

a.

Bleed air from the suspension fluid (See page Suspension>SUSPENSION CONTROL>SUSPENSION CONTROL SYSTEM (w/ KDSS)>BLEEDING).


Hide 17420 9.INSTALL EXHAUST CENTER PIPE ASSEMBLY

a.

for 1GR-FE:

Install the center exhaust pipe (See page Engine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION).


b.

for 1UR-FE:

Install the center exhaust pipe (See page Engine / Hybrid System>1UR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION).


c.

for 3UR-FE:

Install the center exhaust pipe (See page Engine / Hybrid System>3UR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION).


d.

for 1VD-FTV:

Install the center exhaust pipe (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE(w/o DPF)>INSTALLATION).


Hide 17430 10.INSTALL TAILPIPE ASSEMBLY

Hide 48885 12.TIGHTEN REAR STABILIZER CONTROL CYLINDER

a.

Tighten the bolt.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)

NOTICE:

Perform this procedure with all 4 wheels on the ground.



Hide 48884 13.INSTALL REAR STABILIZER CONTROL TUBE INSULATOR

a.
C174360

Install the rear stabilizer control tube insulator with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 48860D 15.CLOSE STABILIZER CONTROL WITH ACCUMULATOR HOUSING SHUTTER VALVE

Hide 48826D 16.INSTALL STABILIZER CONTROL VALVE PROTECTOR