Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering column (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD
2.REMOVE ENGINE ASSEMBLY
for 1UR-FE:
Remove the engine (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL).
for 1GR-FE:
Remove the engine (See page Engine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL).
for 1VD-FTV:
Remove the engine (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL).
for 3UR-FE:
Remove the engine (See page Engine / Hybrid System>3UR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL).
3.REMOVE FRONT WHEELS
48829A
4.LOOSEN NO. 1 FRONT STABILIZER BRACKET LH
w/ KDSS:
Loosen the bracket (See page Suspension>FRONT SUSPENSION>FRONT STABILIZER BAR(w/ KDSS)>REMOVAL).
w/o KDSS:
Loosen the bracket (See page Suspension>FRONT SUSPENSION>FRONT STABILIZER BAR(w/o KDSS)>REMOVAL).
48824A
5.LOOSEN NO. 1 FRONT STABILIZER BRACKET RH
Use the same procedures described for the LH side.
48810
6.REMOVE FRONT STABILIZER LINK ASSEMBLY LH
w/ KDSS:
Remove the front stabilizer link (See page Suspension>FRONT SUSPENSION>FRONT STABILIZER BAR(w/ KDSS)>REMOVAL).
w/o KDSS:
Remove the front stabilizer link (See page Suspension>FRONT SUSPENSION>FRONT STABILIZER BAR(w/o KDSS)>REMOVAL).
48820B
7.REMOVE FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedures described for the LH side.
48829A
8.REMOVE FRONT NO. 1 STABILIZER BRACKET LH
w/ KDSS:
Remove the stabilizer bracket (See page Suspension>FRONT SUSPENSION>FRONT STABILIZER BAR(w/ KDSS)>REMOVAL).
w/o KDSS:
Remove the front bracket (See page Suspension>FRONT SUSPENSION>FRONT STABILIZER BAR(w/o KDSS)>REMOVAL).
48824A
9.REMOVE FRONT NO. 1 STABILIZER BRACKET RH
Use the same procedures described for the LH side.
48811
10.REMOVE FRONT STABILIZER BAR
w/ KDSS:
Remove the stabilizer bar (See page Suspension>FRONT SUSPENSION>FRONT STABILIZER BAR(w/ KDSS)>REMOVAL).
w/o KDSS:
Remove the stabilizer bar (See page Suspension>FRONT SUSPENSION>FRONT STABILIZER BAR(w/o KDSS)>REMOVAL).
45203A
11.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT
for Manual Tilt and Telescopic:
Disconnect the No. 2 steering intermediate shaft (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>REMOVAL).
for Power Tilt and Power Telescopic:
Disconnect the No. 2 steering intermediate shaft (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>REMOVAL).
45047
12.DISCONNECT TIE ROD END SUB-ASSEMBLY LH
45046
13.DISCONNECT TIE ROD END SUB-ASSEMBLY RH
Use the same procedures described for the LH side.
45047
14.REMOVE TIE ROD END SUB-ASSEMBLY LH
Put matchmarks on the tie rod end LH and steering rack end.
Measure length A and record the measurement.
Remove the tie rod end LH.
45046
15.REMOVE TIE ROD END SUB-ASSEMBLY RH
Use the same procedures described for the LH side.
45544B
16.REMOVE STEERING RACK BOOT PROTECTOR LH
Remove the 2 bolts and steering rack boot protector.
45543D
17.REMOVE STEERING RACK BOOT PROTECTOR RH
Use the same procedures described for the LH side.
44410
18.DISCONNECT PRESSURE FEED TUBE ASSEMBLY
Remove the clamp and disconnect the pressure feed tube (return tube side) from the power steering link.
Using a union nut wrench, disconnect the pressure feed tube (pressure feed tube side) from the power steering link.
Remove the 2 bolts and disconnect the pressure feed tube clamp.
51602A
19.REMOVE FRONT SUSPENSION REBOUND STOPPER SUB-ASSEMBLY LH
51601A
20.REMOVE FRONT SUSPENSION REBOUND STOPPER SUB-ASSEMBLY RH
44200
21.REMOVE POWER STEERING LINK ASSEMBLY
Remove the 3 bolts, 3 nuts and power steering link.