Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  Short in CAN Bus Lines  


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
·

Short between CAN bus lines

·

ECM

·

Center airbag sensor assembly*1

·

Headlight swivel ECU assembly*2

·

Multi-media module receiver assembly*3

·

Air conditioning amplifier assembly

·

Main body ECU (cowl side junction block LH)

·

Network gateway ECU*4

·

Combination meter assembly

·

4WD control ECU*5

·

Clearance warning ECU assembly*5, *6

·

Master cylinder solenoid (skid control ECU)*5

·

No. 1 junction connector

·

No. 2 junction connector

·

No. 3 junction connector

·

No. 6 junction connector*5



*1: w/ Airbag System

*2: w/ Dynamic Headlight Auto Leveling

*3: w/ Navigation System

*4: w/ Network Gateway ECU

*5: w/o Network Gateway ECU

*6: w/ TOYOTA Parking Assist-sensor System and w/o Side Monitor System


WIRING DIAGRAM

C258823E01
6.055,1.693 6.429,1.840 0.374,0.147 10 ECM 2.748,3.503 4.370,3.660 1.622,0.158 10 No. 1 Junction Connector 2.748,3.33 3.038,3.511 0.290,0.181 10 E72 2.748,7.657 4.370,7.814 1.622,0.158 10 No. 2 Junction Connector 2.748,7.484 3.038,7.665 0.290,0.181 10 E69 0.114,0.108 2.579,0.288 2.465,0.180 12 w/ Network Gateway ECU: 5.873,0.643 6.338,0.785 0.465,0.141 10 CANH 6.057,1.555 6.370,1.698 0.313,0.143 10 A38 3.85,0.639 4.050,0.810 0.200,0.170 10 2 3.85,1.096 4.050,1.266 0.200,0.170 10 13 3.85,2.447 4.050,2.617 0.200,0.170 10 1 3.85,2.903 4.050,3.073 0.200,0.170 10 12 3.85,3.998 4.050,4.169 0.200,0.170 10 1 3.85,4.455 4.050,4.625 0.200,0.170 10 12 3.09,3.998 3.190,4.169 0.100,0.170 10 2 3.018,4.455 3.190,4.625 0.172,0.170 10 13 3.85,5.827 4.050,5.997 0.200,0.170 10 3 3.85,6.283 4.050,6.453 0.200,0.170 10 14 5.587,5.827 5.764,5.997 0.177,0.170 10 16 5.587,6.283 5.764,6.453 0.177,0.170 10 15 3.09,5.827 3.190,5.997 0.100,0.170 10 5 3.018,6.283 3.190,6.453 0.172,0.170 10 16 5.873,1.283 6.338,1.425 0.465,0.141 10 CANL 0.184,1.708 1.583,2.012 1.399,0.304 10 Headlight Swivel ECU Assembly*3 0.184,1.542 0.528,1.711 0.345,0.169 10 E101 3.092,0.639 3.191,0.810 0.098,0.170 10 3 3.014,1.096 3.190,1.266 0.176,0.170 10 14 1.254,0.651 1.426,0.789 0.172,0.138 10 12 1.254,1.101 1.426,1.239 0.172,0.138 10 13 0.694,0.745 1.113,0.881 0.418,0.137 10 MPX1 0.717,1.194 1.113,1.331 0.396,0.137 10 MPX2 3.094,2.447 3.191,2.617 0.097,0.170 10 4 3.018,2.903 3.190,3.073 0.172,0.170 10 15 0.184,3.515 2.338,3.666 2.155,0.151 10 Center Airbag Sensor Assembly 0.184,3.349 0.487,3.518 0.303,0.169 10 E47 1.254,2.458 1.426,2.596 0.172,0.138 10 13 1.254,2.908 1.426,3.046 0.172,0.138 10 22 0.694,2.552 1.113,2.689 0.418,0.137 10 CANH 0.717,3.001 1.113,3.138 0.396,0.137 10 CANL 0.184,5.056 2.005,5.360 1.821,0.304 10 Multi-media Module Receiver Assembly*4 0.184,4.89 0.487,5.059 0.303,0.169 10 F77 1.254,3.998 1.426,4.136 0.172,0.138 10 1 1.254,4.449 1.426,4.587 0.172,0.138 10 2 0.694,4.092 1.113,4.229 0.418,0.137 10 CANH 0.717,4.541 1.113,4.678 0.396,0.137 10 CANL 5.089,0.621 5.759,0.767 0.670,0.145 10 10*1, 41*2 5.089,1.092 5.759,1.238 0.670,0.145 10 11*1, 49*2 0.18,8.044 1.840,8.191 1.661,0.147 10 *1: except 1VD-FTV 0.18,8.307 1.840,8.454 1.661,0.147 10 *2: for 1VD-FTV 0.18,8.57 2.785,8.717 2.605,0.147 10 *3: w/ Dynamic Headlight Auto Leveling 2.84,8.044 4.416,8.191 1.576,0.147 10 *4: w/ Navigation System 2.84,8.307 5.088,8.454 2.248,0.147 10 *5: w/ Rear Air Conditioning System 2.84,8.57 5.171,8.717 2.332,0.147 10 *6: w/o Rear Air Conditioning System 0.184,6.751 1.790,7.055 1.606,0.304 10 Air Conditioning Amplifier Assembly 1.269,6.386 1.540,6.523 0.270,0.136 10 E35 1.291,6.187 1.518,6.323 0.227,0.136 10 4*5 1.269,5.933 1.540,6.069 0.270,0.136 10 E35 1.291,5.733 1.518,5.869 0.227,0.136 10 3*5 1.657,6.386 1.927,6.523 0.270,0.136 10 E81 1.64,6.187 1.944,6.323 0.303,0.136 10 12*6 1.657,5.933 1.927,6.069 0.270,0.136 10 E81 1.639,5.733 1.945,5.869 0.307,0.136 10 11*6 5.873,5.934 6.291,6.071 0.419,0.137 10 CA1H 5.873,6.383 6.268,6.520 0.396,0.137 10 CA1L 0.694,5.934 1.113,6.071 0.418,0.137 10 CANH 0.717,6.383 1.113,6.520 0.396,0.137 10 CANL 5.54,6.882 7.014,7.024 1.474,0.142 10 Network Gateway ECU 5.54,6.716 5.843,6.885 0.303,0.169 10 E31 3.09,6.677 3.190,6.847 0.100,0.170 10 4 3.018,7.133 3.190,7.303 0.172,0.170 10 15

C258824E01
5.69,4.03 6.890,4.335 1.200,0.305 10 Combination Meter Assembly 2.748,4.055 4.369,4.212 1.622,0.158 10 No. 3 Junction Connector 2.748,3.897 3.037,4.037 0.290,0.140 10 E75 0.113,0.073 2.578,0.253 2.465,0.180 12 w/ Network Gateway ECU: 5.872,2.981 6.337,3.122 0.465,0.141 10 CANH 5.693,3.893 6.005,4.035 0.313,0.143 10 E7 3.864,1.104 4.064,1.274 0.200,0.170 10 4 3.864,1.518 4.064,1.689 0.200,0.170 10 15 3.864,2.986 4.064,3.156 0.200,0.170 10 3 3.864,3.428 4.064,3.599 0.200,0.170 10 14 5.872,3.621 6.337,3.762 0.465,0.141 10 CANL 3.078,1.104 3.176,1.274 0.098,0.170 10 1 3,1.518 3.175,1.689 0.176,0.170 10 12 3.079,2.986 3.176,3.156 0.097,0.170 10 2 3.003,3.428 3.175,3.599 0.172,0.170 10 13 0.585,4.055 0.959,4.206 0.374,0.151 10 DLC3 0.585,3.897 0.888,4.042 0.303,0.144 10 E22 1.254,2.997 1.426,3.135 0.172,0.138 10 6 1.254,3.447 1.426,3.586 0.172,0.138 10 14 0.694,3.091 1.112,3.228 0.418,0.137 10 CANH 0.717,3.54 1.112,3.677 0.396,0.137 10 CANL 5.579,2.986 5.758,3.131 0.179,0.145 10 25 5.579,3.428 5.758,3.574 0.179,0.145 10 26 5.662,1.104 5.759,1.274 0.097,0.170 10 5 5.662,1.518 5.759,1.689 0.097,0.170 10 6 5.872,1.211 6.291,1.348 0.418,0.137 10 CANH 5.872,1.646 6.268,1.783 0.396,0.137 10 CANL 5.54,2.134 7.038,2.439 1.498,0.305 10 Main Body ECU (Cowl Side Junction Block LH) 5.54,1.996 5.843,2.165 0.303,0.169 10 E3

U165282E01
6.054,1.632 6.428,1.780 0.374,0.147 10 ECM 2.748,3.26 4.369,3.417 1.622,0.158 10 No. 1 Junction Connector 2.748,3.087 3.037,3.268 0.290,0.181 10 E72 0.113,0.048 2.578,0.228 2.465,0.180 12 w/o Network Gateway ECU: 5.872,0.583 6.337,0.724 0.465,0.141 10 CANH 6.057,1.495 6.369,1.637 0.313,0.143 10 A38 3.849,0.579 4.049,0.749 0.200,0.170 10 2 3.849,1.035 4.049,1.205 0.200,0.170 10 13 3.849,2.204 4.049,2.374 0.200,0.170 10 1 3.849,2.66 4.049,2.830 0.200,0.170 10 12 2.748,6.01 4.369,6.168 1.622,0.158 10 No. 2 Junction Connector 2.748,5.838 3.037,6.019 0.290,0.181 10 E69 3.849,3.755 4.049,3.926 0.200,0.170 10 1 3.849,4.212 4.049,4.382 0.200,0.170 10 12 3.089,3.755 3.190,3.926 0.100,0.170 10 2 3.017,4.212 3.189,4.382 0.172,0.170 10 13 3.849,4.928 4.049,5.099 0.200,0.170 10 5 3.849,5.385 4.049,5.555 0.200,0.170 10 16 3.089,4.928 3.190,5.099 0.100,0.170 10 4 3.017,5.385 3.189,5.555 0.172,0.170 10 15 2.748,8.517 4.369,8.675 1.622,0.158 10 No. 6 Junction Connector 2.748,8.373 3.037,8.554 0.290,0.181 10 F73 3.849,6.635 4.049,6.805 0.200,0.170 10 5 3.849,7.091 4.049,7.261 0.200,0.170 10 16 5.652,6.635 5.760,6.805 0.107,0.170 10 3 5.652,7.091 5.760,7.261 0.107,0.170 10 5 3.089,6.635 3.190,6.805 0.100,0.170 10 7 3.017,7.091 3.189,7.261 0.172,0.170 10 18 3.849,7.478 4.049,7.648 0.200,0.170 10 6 3.849,7.934 4.049,8.104 0.200,0.170 10 17 5.872,1.223 6.337,1.364 0.465,0.141 10 CANL 3.092,0.579 3.190,0.749 0.098,0.170 10 4 3.014,1.035 3.189,1.205 0.176,0.170 10 15 3.093,2.204 3.190,2.374 0.097,0.170 10 5 3.017,2.66 3.189,2.830 0.172,0.170 10 16 0.253,3.273 1.422,3.423 1.168,0.151 10 4WD Control ECU 0.253,3.106 0.556,3.275 0.303,0.169 10 A27 1.254,2.215 1.426,2.353 0.172,0.138 10 19 1.254,2.665 1.426,2.803 0.172,0.138 10 20 0.717,2.309 1.112,2.446 0.395,0.137 10 CAN+ 0.75,2.758 1.113,2.895 0.363,0.137 10 CAN- 0.183,4.813 2.004,5.117 1.821,0.304 10 Multi-media Module Receiver Assembly*4 0.183,4.647 0.486,4.816 0.303,0.169 10 F77 1.254,3.755 1.426,3.893 0.172,0.138 10 1 1.254,4.206 1.426,4.344 0.172,0.138 10 2 0.694,3.849 1.112,3.986 0.418,0.137 10 CANH 0.717,4.299 1.112,4.435 0.396,0.137 10 CANL 5.089,0.561 5.759,0.706 0.670,0.145 10 10*1, 41*2 5.089,1.032 5.759,1.177 0.670,0.145 10 11*1, 49*2 0.086,6.438 1.746,6.584 1.661,0.147 10 *1: for 1GR-FE, 1UR-FE 0.086,6.706 1.746,6.852 1.661,0.147 10 *2: for 1VD-FTV 0.086,7.242 2.115,7.389 2.029,0.147 10 *4: w/ Navigation System 0.086,6.974 2.115,7.121 2.029,0.147 10 *3: w/ Airbag System 0.086,7.51 2.425,7.657 2.339,0.147 10 *5: w/ Rear Air Conditioning System 0.086,7.778 2.452,7.925 2.367,0.147 10 *6: w/o Rear Air Conditioning System 0.086,8.046 2.656,8.351 2.570,0.305 10 *7: w/ TOYOTA Parking Assist-sensor System and w/o Side Monitor System 5.374,5.881 6.980,6.185 1.606,0.304 10 Air Conditioning Amplifier Assembly 5.56,7.69 7.120,7.995 1.560,0.304 10 Clearance Warning ECU Assembly*7 5.476,5.516 5.746,5.652 0.270,0.136 10 E35 5.498,5.316 5.725,5.453 0.227,0.136 10 4*5 5.476,5.062 5.746,5.199 0.270,0.136 10 E35 5.498,4.863 5.725,4.999 0.227,0.136 10 3*5 5.1,5.516 5.370,5.652 0.270,0.136 10 E81 5.083,5.316 5.387,5.453 0.303,0.136 10 12*6 5.1,5.062 5.370,5.199 0.270,0.136 10 E81 5.082,4.863 5.388,4.999 0.307,0.136 10 11*6 5.872,5.063 6.291,5.200 0.418,0.137 10 CANH 5.872,5.513 6.268,5.650 0.396,0.137 10 CANL 5.872,6.754 6.291,6.891 0.418,0.137 10 CANH 5.872,7.203 6.268,7.340 0.396,0.137 10 CANL 0.295,1.648 2.464,1.801 2.168,0.153 10 Center Airbag Sensor Assembly*3 0.295,1.481 0.598,1.650 0.303,0.169 10 E47 1.254,0.59 1.426,0.728 0.172,0.138 10 13 1.254,1.04 1.426,1.179 0.172,0.138 10 22 0.694,0.684 1.112,0.821 0.418,0.137 10 CANH 0.717,1.133 1.112,1.270 0.396,0.137 10 CANL 5.56,7.547 5.830,7.684 0.270,0.136 10 F12

C258826E01
5.691,5.064 6.890,5.369 1.200,0.305 10 Combination Meter Assembly 2.748,5.089 4.369,5.246 1.622,0.158 10 No. 3 Junction Connector 2.748,4.931 3.038,5.071 0.290,0.140 10 E75 0.113,0.08 2.579,0.259 2.465,0.180 12 w/o Network Gateway ECU: 5.873,4.015 6.337,4.156 0.465,0.141 10 CANH 5.693,4.927 6.006,5.069 0.313,0.143 10 E7 3.864,2.186 4.064,2.356 0.200,0.170 10 4 3.864,2.6 4.064,2.771 0.200,0.170 10 15 3.864,4.02 4.064,4.190 0.200,0.170 10 3 3.864,4.462 4.064,4.633 0.200,0.170 10 14 5.873,4.654 6.337,4.796 0.465,0.141 10 CANL 3.864,1.11 3.962,1.281 0.098,0.170 10 1 3.864,1.525 4.040,1.695 0.176,0.170 10 12 3.078,1.125 3.176,1.295 0.098,0.170 10 5 3,1.539 3.176,1.709 0.176,0.170 10 16 3.079,4.02 3.176,4.190 0.097,0.170 10 2 3.003,4.462 3.176,4.633 0.172,0.170 10 13 0.585,5.089 0.960,5.239 0.374,0.151 10 DLC3 0.585,4.931 0.888,5.076 0.303,0.144 10 E22 1.282,4.031 1.455,4.169 0.172,0.138 10 6 1.282,4.481 1.455,4.620 0.172,0.138 10 14 0.703,4.125 1.121,4.262 0.418,0.137 10 CANH 0.726,4.574 1.121,4.711 0.396,0.137 10 CANL 5.58,4.02 5.759,4.165 0.179,0.145 10 25 5.58,4.462 5.759,4.608 0.179,0.145 10 26 5.662,2.186 5.759,2.356 0.097,0.170 10 5 5.662,2.6 5.759,2.771 0.097,0.170 10 6 5.873,2.293 6.291,2.430 0.418,0.137 10 CANH 5.873,2.728 6.268,2.865 0.396,0.137 10 CANL 5.54,3.217 7.038,3.521 1.498,0.305 10 Main Body ECU (Cowl Side Junction Block LH) 5.54,3.078 5.843,3.247 0.303,0.169 10 E3 1.282,1.125 1.459,1.295 0.177,0.170 10 11 1.282,1.539 1.459,1.709 0.177,0.170 10 25 0.703,1.228 1.121,1.365 0.418,0.137 10 CANH 0.726,1.635 1.121,1.772 0.396,0.137 10 CANL 0.37,2.152 1.959,2.456 1.589,0.305 10 Master Cylinder Solenoid (Skid Control ECU) 0.37,2.014 0.673,2.182 0.303,0.169 10 A24

CAUTION / NOTICE / HINT

HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR SHORT IN CAN BUS WIRES (DLC3 CAN BRANCH WIRE)
3.CHECK FOR SHORT IN CAN BUS WIRES (DLC3 CAN BRANCH WIRE)
a.
C253362C22
0.167,1.01 0.563,1.271 0.396,0.26 1.948,0.906 2.135,0.417 2.135,0.417 2.271,0.417 false 1.948,1.458 1.802,1.885 1.802,1.885 1.667,1.885 false 0.052,0.021 0.219,0.208 0.167,0.188 10 false *a 2.333,0.323 2.802,0.51 0.469,0.188 10 false CANH 1.26,1.813 1.667,2 0.406,0.188 10 false CANL 0.229,1.063 0.552,1.271 0.323,0.208 10 false E22

Disconnect the E75 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E22-6 (CANH) - E22-14 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Front view of DLC3



OK

4.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

4.CONNECT CONNECTOR
a.

Reconnect the E75 No. 3 junction connector.



NEXT

5.SYSTEM CHECK
5.SYSTEM CHECK
a.

Check the vehicle specifications.

Result
Result Proceed to
w/ Network Gateway ECU A
w/o Network Gateway ECU B



A

6.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)

B

28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)
6.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)
a.
C253362C22
0.167,1.01 0.563,1.271 0.396,0.26 1.948,0.906 2.135,0.417 2.135,0.417 2.271,0.417 false 1.948,1.458 1.802,1.885 1.802,1.885 1.667,1.885 false 0.052,0.021 0.219,0.208 0.167,0.188 10 false *a 2.333,0.323 2.802,0.51 0.469,0.188 10 false CANH 1.26,1.813 1.667,2 0.406,0.188 10 false CANL 0.229,1.063 0.552,1.271 0.323,0.208 10 false E22

Disconnect the E72 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E22-6 (CANH) - E22-14 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of DLC3



OK

7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - HEADLIGHT SWIVEL ECU ASSEMBLY)

NG

13.CONNECT CONNECTOR
7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - HEADLIGHT SWIVEL ECU ASSEMBLY)
NOTICE:

For vehicles without dynamic headlight auto leveling, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - Center Airbag Sensor Assembly)".


a.
U166153E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E72 2.581,1.872 3.000,2.014 0.419,0.142 10 CANH 2.472,2.78 2.891,2.922 0.419,0.142 10 CANL 2.04,2.461 2.283,2.856 2.283,2.856 2.449,2.856 false 2.04,2.325 2.392,1.938 2.392,1.938 2.558,1.938 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-3 (CANH) - E72-14 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

8.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

NG

10.CHECK FOR SHORT IN CAN BUS WIRES (HEADLIGHT SWIVEL ECU ASSEMBLY)
8.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)
a.
U166154E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E72 2.586,1.872 3.004,2.014 0.419,0.142 10 CANH 2.372,2.78 2.790,2.922 0.419,0.142 10 CANL 1.939,2.461 2.183,2.856 2.183,2.856 2.349,2.856 false 1.939,2.325 2.397,1.938 2.397,1.938 2.563,1.938 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-4 (CANH) - E72-15 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM)

NG

11.CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY)
9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM)
a.
U166155E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E72 2.595,2.04 3.014,2.182 0.419,0.142 10 CANH 2.577,2.694 2.996,2.836 0.419,0.142 10 CANL 2.144,2.461 2.388,2.77 2.388,2.77 2.554,2.77 false 2.144,2.325 2.406,2.106 2.406,2.106 2.572,2.106 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-2 (CANH) - E72-13 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

12.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
10.CHECK FOR SHORT IN CAN BUS WIRES (HEADLIGHT SWIVEL ECU ASSEMBLY)
a.
U166153E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E72 2.581,1.872 3.000,2.014 0.419,0.142 10 CANH 2.472,2.78 2.891,2.922 0.419,0.142 10 CANL 2.04,2.461 2.283,2.856 2.283,2.856 2.449,2.856 false 2.04,2.325 2.392,1.938 2.392,1.938 2.558,1.938 false

Disconnect the E101 headlight swivel ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-3 (CANH) - E72-14 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO HEADLIGHT SWIVEL ECU ASSEMBLY (MPX1, MPX2)

11.CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY)
a.
U166154E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E72 2.586,1.872 3.004,2.014 0.419,0.142 10 CANH 2.372,2.78 2.790,2.922 0.419,0.142 10 CANL 1.939,2.461 2.183,2.856 2.183,2.856 2.349,2.856 false 1.939,2.325 2.397,1.938 2.397,1.938 2.563,1.938 false

Disconnect the E47 center airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-4 (CANH) - E72-15 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)

12.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
U166155E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E72 2.595,2.04 3.014,2.182 0.419,0.142 10 CANH 2.577,2.694 2.996,2.836 0.419,0.142 10 CANL 2.144,2.461 2.388,2.77 2.388,2.77 2.554,2.77 false 2.144,2.325 2.406,2.106 2.406,2.106 2.572,2.106 false

Disconnect the A38 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-2 (CANH) - E72-13 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)

Result
Result Proceed to
OK (for 1GR-FE) A
OK (for 1UR-FE) B
OK (for 3UR-FE) C
OK (for 1VD-FTV) D
NG E



A

B

C

D

E

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

13.CONNECT CONNECTOR
a.

Reconnect the E72 No. 1 junction connector.



NEXT

14.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
14.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
a.
U166156E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E69 2.62,2.082 3.039,2.224 0.419,0.142 10 CANH 2.62,2.608 3.039,2.750 0.419,0.142 10 CANL 2.253,2.478 2.414,2.685 2.414,2.685 2.58,2.685 false 2.253,2.325 2.423,2.165 2.423,2.165 2.589,2.165 false

Disconnect the E69 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-1 (CANH) - E69-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

15.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

15.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)
a.
C253362C22
0.167,1.01 0.563,1.271 0.396,0.26 1.948,0.906 2.135,0.417 2.135,0.417 2.271,0.417 false 1.948,1.458 1.802,1.885 1.802,1.885 1.667,1.885 false 0.052,0.021 0.219,0.208 0.167,0.188 10 false *a 2.333,0.323 2.802,0.51 0.469,0.188 10 false CANH 1.26,1.813 1.667,2 0.406,0.188 10 false CANL 0.229,1.063 0.552,1.271 0.323,0.208 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E22-6 (CANH) - E22-14 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of DLC3



OK

16.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - MULTI-MEDIA MODULE RECEIVER ASSEMBLY)

NG

22.CONNECT CONNECTOR
16.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - MULTI-MEDIA MODULE RECEIVER ASSEMBLY)
NOTICE:

For vehicles without a navigation system, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Air Conditioning Amplifier Assembly)".


a.
U166157E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E69 2.595,2.04 3.014,2.182 0.419,0.142 10 CANH 2.577,2.694 2.996,2.836 0.419,0.142 10 CANL 2.144,2.461 2.388,2.77 2.388,2.77 2.554,2.77 false 2.144,2.325 2.406,2.106 2.406,2.106 2.572,2.106 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-2 (CANH) - E69-13 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

17.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

19.CHECK FOR SHORT IN CAN BUS WIRES (MULTI-MEDIA MODULE RECEIVER ASSEMBLY)
17.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.
U166158E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E69 2.586,1.786 3.005,1.928 0.419,0.142 10 CANH 2.349,2.905 2.768,3.047 0.419,0.142 10 CANL 1.826,2.496 2.16,2.981 2.16,2.981 2.326,2.981 false 1.827,2.325 2.397,1.852 2.397,1.852 2.563,1.852 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-5 (CANH) - E69-16 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

18.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

NG

20.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)
18.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
a.
U166159E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E69 2.595,1.957 3.014,2.099 0.419,0.142 10 CANH 2.491,2.78 2.910,2.922 0.419,0.142 10 CANL 2.034,2.461 2.302,2.856 2.302,2.856 2.468,2.856 false 2.034,2.325 2.406,2.023 2.406,2.023 2.572,2.023 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-3 (CANH) - E69-14 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

21.CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU)
19.CHECK FOR SHORT IN CAN BUS WIRES (MULTI-MEDIA MODULE RECEIVER ASSEMBLY)
a.
U166157E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E69 2.595,2.04 3.014,2.182 0.419,0.142 10 CANH 2.577,2.694 2.996,2.836 0.419,0.142 10 CANL 2.144,2.461 2.388,2.77 2.388,2.77 2.554,2.77 false 2.144,2.325 2.406,2.106 2.406,2.106 2.572,2.106 false

Disconnect the F77 multi-media module receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-2 (CANH) - E69-13 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTI-MEDIA MODULE RECEIVER ASSEMBLY (CANH, CANL)

20.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.
U166158E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E69 2.586,1.786 3.005,1.928 0.419,0.142 10 CANH 2.349,2.905 2.768,3.047 0.419,0.142 10 CANL 1.826,2.496 2.16,2.981 2.16,2.981 2.326,2.981 false 1.827,2.325 2.397,1.852 2.397,1.852 2.563,1.852 false

Disconnect the E35*1 or E81*2 air conditioning amplifier assembly connector.

*1: w/ Rear Air Conditioning System

*2: w/o Rear Air Conditioning System


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-5 (CANH) - E69-16 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

21.CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU)
a.
U166159E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E69 2.595,1.957 3.014,2.099 0.419,0.142 10 CANH 2.491,2.78 2.910,2.922 0.419,0.142 10 CANL 2.034,2.461 2.302,2.856 2.302,2.856 2.468,2.856 false 2.034,2.325 2.406,2.023 2.406,2.023 2.572,2.023 false

Disconnect the E31 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-3 (CANH) - E69-14 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NETWORK GATEWAY ECU (CA1H, CA1L)

22.CONNECT CONNECTOR
a.

Reconnect the E69 No. 2 junction connector.



NEXT

23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
a.
U166160E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E75 2.63,2.075 3.049,2.217 0.419,0.142 10 CANH 2.654,2.617 3.073,2.759 0.419,0.142 10 CANL 2.265,2.461 2.465,2.694 2.465,2.694 2.631,2.694 false 2.265,2.325 2.441,2.141 2.441,2.141 2.607,2.141 false

Disconnect the E75 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E75-1 (CANH) - E75-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

24.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

24.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U166161E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E75 2.569,1.864 2.988,2.006 0.419,0.142 10 CANH 2.418,2.806 2.837,2.948 0.419,0.142 10 CANL 1.943,2.461 2.229,2.882 2.229,2.882 2.395,2.882 false 1.943,2.325 2.38,1.93 2.38,1.93 2.546,1.93 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E75-4 (CANH) - E75-15 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

25.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

26.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
25.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U166162E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E75 2.603,1.886 3.022,2.028 0.419,0.142 10 CANH 2.491,2.806 2.910,2.948 0.419,0.142 10 CANL 2.041,2.461 2.285,2.882 2.285,2.882 2.468,2.882 false 2.041,2.325 2.38,1.952 2.38,1.952 2.58,1.952 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E75-3 (CANH) - E75-14 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

27.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
26.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
a.
U166161E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E75 2.569,1.864 2.988,2.006 0.419,0.142 10 CANH 2.418,2.806 2.837,2.948 0.419,0.142 10 CANL 1.943,2.461 2.229,2.882 2.229,2.882 2.395,2.882 false 1.943,2.325 2.38,1.93 2.38,1.93 2.546,1.93 false

Disconnect the E3 main body ECU (cowl side junction block LH) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E75-4 (CANH) - E75-15 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)

27.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
a.
U166162E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E75 2.603,1.886 3.022,2.028 0.419,0.142 10 CANH 2.491,2.806 2.910,2.948 0.419,0.142 10 CANL 2.041,2.461 2.285,2.882 2.285,2.882 2.468,2.882 false 2.041,2.325 2.38,1.952 2.38,1.952 2.58,1.952 false

Disconnect the E7 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E75-3 (CANH) - E75-14 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)

Result
Result Proceed to
OK (w/ Multi-information Display) A
OK (w/o Multi-information Display) B
NG C



A

B

C

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)
a.
C253362C22
0.167,1.01 0.563,1.271 0.396,0.26 1.948,0.906 2.135,0.417 2.135,0.417 2.271,0.417 false 1.948,1.458 1.802,1.885 1.802,1.885 1.667,1.885 false 0.052,0.021 0.219,0.208 0.167,0.188 10 false *a 2.333,0.323 2.802,0.51 0.469,0.188 10 false CANH 1.26,1.813 1.667,2 0.406,0.188 10 false CANL 0.229,1.063 0.552,1.271 0.323,0.208 10 false E22

Disconnect the E72 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E22-6 (CANH) - E22-14 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of DLC3



OK

29.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

NG

35.CONNECT CONNECTOR
29.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)
NOTICE:

For vehicles without an airbag system, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - 4WD Control ECU)".


a.
U166154E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E72 2.586,1.872 3.004,2.014 0.419,0.142 10 CANH 2.372,2.78 2.790,2.922 0.419,0.142 10 CANL 1.939,2.461 2.183,2.856 2.183,2.856 2.349,2.856 false 1.939,2.325 2.397,1.938 2.397,1.938 2.563,1.938 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-4 (CANH) - E72-15 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - 4WD CONTROL ECU)

NG

32.CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY)
30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - 4WD CONTROL ECU)
a.
U166163E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E72 2.53,1.76 2.948,1.902 0.419,0.142 10 CANH 2.3,2.852 2.718,2.994 0.419,0.142 10 CANL 1.819,2.461 2.111,2.928 2.111,2.928 2.277,2.928 false 1.819,2.325 2.341,1.826 2.341,1.826 2.507,1.826 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-5 (CANH) - E72-16 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM)

NG

33.CHECK FOR SHORT IN CAN BUS WIRES (4WD CONTROL ECU)
31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM)
a.
U166155E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E72 2.595,2.04 3.014,2.182 0.419,0.142 10 CANH 2.577,2.694 2.996,2.836 0.419,0.142 10 CANL 2.144,2.461 2.388,2.77 2.388,2.77 2.554,2.77 false 2.144,2.325 2.406,2.106 2.406,2.106 2.572,2.106 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-2 (CANH) - E72-13 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

34.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
32.CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY)
a.
U166154E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E72 2.586,1.872 3.004,2.014 0.419,0.142 10 CANH 2.372,2.78 2.790,2.922 0.419,0.142 10 CANL 1.939,2.461 2.183,2.856 2.183,2.856 2.349,2.856 false 1.939,2.325 2.397,1.938 2.397,1.938 2.563,1.938 false

Disconnect the E47 center airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-4 (CANH) - E72-15 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)

33.CHECK FOR SHORT IN CAN BUS WIRES (4WD CONTROL ECU)
a.
U166163E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E72 2.53,1.76 2.948,1.902 0.419,0.142 10 CANH 2.3,2.852 2.718,2.994 0.419,0.142 10 CANL 1.819,2.461 2.111,2.928 2.111,2.928 2.277,2.928 false 1.819,2.325 2.341,1.826 2.341,1.826 2.507,1.826 false

Disconnect the A27 4WD control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-5 (CANH) - E72-16 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CAN+, CAN-)

34.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
U166155E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E72 2.595,2.04 3.014,2.182 0.419,0.142 10 CANH 2.577,2.694 2.996,2.836 0.419,0.142 10 CANL 2.144,2.461 2.388,2.77 2.388,2.77 2.554,2.77 false 2.144,2.325 2.406,2.106 2.406,2.106 2.572,2.106 false

Disconnect the A38 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-2 (CANH) - E72-13 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)

Result
Result Proceed to
OK (for 1GR-FE) A
OK (for 1UZ-FE) B
OK (for 1VD-FTV) C
NG D



A

B

C

D

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

35.CONNECT CONNECTOR
a.

Reconnect the E72 No. 1 junction connector.



NEXT

36.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
36.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
a.
U166156E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E69 2.62,2.082 3.039,2.224 0.419,0.142 10 CANH 2.62,2.608 3.039,2.750 0.419,0.142 10 CANL 2.253,2.478 2.414,2.685 2.414,2.685 2.58,2.685 false 2.253,2.325 2.423,2.165 2.423,2.165 2.589,2.165 false

Disconnect the E69 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-1 (CANH) - E69-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

37.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

37.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)
a.
C253362C22
0.167,1.01 0.563,1.271 0.396,0.26 1.948,0.906 2.135,0.417 2.135,0.417 2.271,0.417 false 1.948,1.458 1.802,1.885 1.802,1.885 1.667,1.885 false 0.052,0.021 0.219,0.208 0.167,0.188 10 false *a 2.333,0.323 2.802,0.51 0.469,0.188 10 false CANH 1.26,1.813 1.667,2 0.406,0.188 10 false CANL 0.229,1.063 0.552,1.271 0.323,0.208 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E22-6 (CANH) - E22-14 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of DLC3



OK

38.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - MULTI-MEDIA MODULE RECEIVER ASSEMBLY)

NG

42.CONNECT CONNECTOR
38.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - MULTI-MEDIA MODULE RECEIVER ASSEMBLY)
NOTICE:

For vehicles without a navigation system, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Air Conditioning Amplifier)".


a.
U166157E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E69 2.595,2.04 3.014,2.182 0.419,0.142 10 CANH 2.577,2.694 2.996,2.836 0.419,0.142 10 CANL 2.144,2.461 2.388,2.77 2.388,2.77 2.554,2.77 false 2.144,2.325 2.406,2.106 2.406,2.106 2.572,2.106 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-2 (CANH) - E69-13 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

40.CHECK FOR SHORT IN CAN BUS WIRES (MULTI-MEDIA MODULE RECEIVER ASSEMBLY)
39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.
U166158E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E69 2.586,1.786 3.005,1.928 0.419,0.142 10 CANH 2.349,2.905 2.768,3.047 0.419,0.142 10 CANL 1.826,2.496 2.16,2.981 2.16,2.981 2.326,2.981 false 1.827,2.325 2.397,1.852 2.397,1.852 2.563,1.852 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-5 (CANH) - E69-16 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

41.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)
40.CHECK FOR SHORT IN CAN BUS WIRES (MULTI-MEDIA MODULE RECEIVER ASSEMBLY)
a.
U166157E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E69 2.595,2.04 3.014,2.182 0.419,0.142 10 CANH 2.577,2.694 2.996,2.836 0.419,0.142 10 CANL 2.144,2.461 2.388,2.77 2.388,2.77 2.554,2.77 false 2.144,2.325 2.406,2.106 2.406,2.106 2.572,2.106 false

Disconnect the F77 multi-media module receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-2 (CANH) - E69-13 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTI-MEDIA MODULE RECEIVER ASSEMBLY (CANH, CANL)

41.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.
U166158E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E69 2.586,1.786 3.005,1.928 0.419,0.142 10 CANH 2.349,2.905 2.768,3.047 0.419,0.142 10 CANL 1.826,2.496 2.16,2.981 2.16,2.981 2.326,2.981 false 1.827,2.325 2.397,1.852 2.397,1.852 2.563,1.852 false

Disconnect the E35*1 or E81*2 air conditioning amplifier connector.

*1: w/ Rear Air Conditioning System

*2: w/o Rear Air Conditioning System



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-5 (CANH) - E69-16 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

42.CONNECT CONNECTOR
a.

Reconnect the E69 No. 2 junction connector.



NEXT

43.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
43.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
a.
U166152E02
1.594,2.49 1.271,2.938 1.271,2.938 1.146,2.938 false 1.594,2.323 1.094,1.833 1.094,1.833 0.958,1.833 false 2.688,2.323 2.99,2.531 0.302,0.208 10 false F73 0.104,0.094 0.354,0.333 0.25,0.24 10 false *a 0.438,1.76 0.948,1.99 0.51,0.229 10 false CANH 0.646,2.865 1.115,3.094 0.469,0.229 10 false CANL

Disconnect the F73 No. 6 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F73-7 (CANH) - F73-18 (CANL) Ignition switch off 108 to 132 Ω

Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)




OK

44.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR SIDE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

44.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR SIDE)
a.
C253362C22
0.167,1.01 0.563,1.271 0.396,0.26 1.948,0.906 2.135,0.417 2.135,0.417 2.271,0.417 false 1.948,1.458 1.802,1.885 1.802,1.885 1.667,1.885 false 0.052,0.021 0.219,0.208 0.167,0.188 10 false *a 2.333,0.323 2.802,0.51 0.469,0.188 10 false CANH 1.26,1.813 1.667,2 0.406,0.188 10 false CANL 0.229,1.063 0.552,1.271 0.323,0.208 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E22-6 (CANH) - E22-14 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of DLC3

Result
Result Proceed to
OK (w/ TOYOTA parking assist-sensor system) A
OK (w/o TOYOTA parking assist-sensor system) B
NG C



A

45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)

B

REPLACE NO. 6 JUNCTION CONNECTOR

C

47.CONNECT CONNECTOR
45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)
a.
U166164E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 F73 2.577,1.855 2.995,1.997 0.419,0.142 10 CANH 2.274,2.858 2.693,3.000 0.419,0.142 10 CANL 1.825,2.496 2.085,2.934 2.085,2.934 2.252,2.934 false 1.825,2.308 2.388,1.921 2.388,1.921 2.554,1.921 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F73-5 (CANH) - F73-16 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)



OK

REPLACE NO. 6 JUNCTION CONNECTOR

NG

46.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
46.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.
U166164E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 F73 2.577,1.855 2.995,1.997 0.419,0.142 10 CANH 2.274,2.858 2.693,3.000 0.419,0.142 10 CANL 1.825,2.496 2.085,2.934 2.085,2.934 2.252,2.934 false 1.825,2.308 2.388,1.921 2.388,1.921 2.554,1.921 false

Disconnect the F12 clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F73-5 (CANH) - F73-16 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CLEARANCE WARNING ECU ASSEMBLY (CANH, CANL)

47.CONNECT CONNECTOR
a.

Reconnect the F73 No. 6 junction connector.



NEXT

48.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
48.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
a.
U166165E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E75 2.602,2.061 3.021,2.203 0.419,0.142 10 CANH 2.604,2.668 3.022,2.810 0.419,0.142 10 CANL 2.262,2.496 2.415,2.745 2.415,2.745 2.581,2.745 false 2.262,2.325 2.413,2.127 2.413,2.127 2.58,2.127 false

Disconnect the E75 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E75-1 (CANH) - E75-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

49.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

49.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U166161E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E75 2.569,1.864 2.988,2.006 0.419,0.142 10 CANH 2.418,2.806 2.837,2.948 0.419,0.142 10 CANL 1.943,2.461 2.229,2.882 2.229,2.882 2.395,2.882 false 1.943,2.325 2.38,1.93 2.38,1.93 2.546,1.93 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E75-4 (CANH) - E75-15 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

50.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - SKID CONTROL ECU)

NG

52.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
50.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - SKID CONTROL ECU)
a.
U166166E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E75 2.595,1.736 3.013,1.878 0.419,0.142 10 CANH 2.272,2.841 2.691,2.983 0.419,0.142 10 CANL 1.822,2.496 2.066,2.917 2.066,2.917 2.249,2.917 false 1.822,2.325 2.371,1.802 2.371,1.802 2.572,1.802 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E75-5 (CANH) - E75-16 (CANL) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

51.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

53.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)
51.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U166162E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E75 2.603,1.886 3.022,2.028 0.419,0.142 10 CANH 2.491,2.806 2.910,2.948 0.419,0.142 10 CANL 2.041,2.461 2.285,2.882 2.285,2.882 2.468,2.882 false 2.041,2.325 2.38,1.952 2.38,1.952 2.58,1.952 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E75-3 (CANH) - E75-14 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

54.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
52.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
a.
U166161E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E75 2.569,1.864 2.988,2.006 0.419,0.142 10 CANH 2.418,2.806 2.837,2.948 0.419,0.142 10 CANL 1.943,2.461 2.229,2.882 2.229,2.882 2.395,2.882 false 1.943,2.325 2.38,1.93 2.38,1.93 2.546,1.93 false

Disconnect the E3 main body ECU (cowl side junction block LH) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E75-4 (CANH) - E75-15 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)

53.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)
a.
U166166E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E75 2.595,1.736 3.013,1.878 0.419,0.142 10 CANH 2.272,2.841 2.691,2.983 0.419,0.142 10 CANL 1.822,2.496 2.066,2.917 2.066,2.917 2.249,2.917 false 1.822,2.325 2.371,1.802 2.371,1.802 2.572,1.802 false

Disconnect the A24 master cylinder solenoid (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E75-5 (CANH) - E75-16 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

54.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
a.
U166162E01
0.066,0.073 0.239,0.215 0.173,0.142 10 *a 0.418,2.334 0.684,2.476 0.266,0.142 10 E75 2.603,1.886 3.022,2.028 0.419,0.142 10 CANH 2.491,2.806 2.910,2.948 0.419,0.142 10 CANL 2.041,2.461 2.285,2.882 2.285,2.882 2.468,2.882 false 2.041,2.325 2.38,1.952 2.38,1.952 2.58,1.952 false

Disconnect the E7 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E75-3 (CANH) - E75-14 (CANL) Ignition switch off 1 MΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)

Result
Result Proceed to
OK (w/ Multi-information Display) A
OK (w/o Multi-information Display) B
NG C



A

B

C

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)