There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
| Symptom | Trouble Area |
|---|---|
| The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω. | ·
Short between CAN bus lines and GND ·
ECM ·
Center airbag sensor assembly*1 ·
Headlight swivel ECU assembly*2 ·
Multi-media module receiver assembly*3 ·
Air conditioning amplifier assembly ·
Main body ECU (cowl side junction block LH) ·
Network gateway ECU*4 ·
Combination meter assembly ·
4WD control ECU*5 ·
Clearance warning ECU assembly*5, *6 ·
Master cylinder solenoid (skid control ECU)*5 ·
No. 1 junction connector ·
No. 2 junction connector ·
No. 3 junction connector ·
No. 6 junction connector*5 |
*1: w/ Airbag System
*2: w/ Dynamic Headlight Auto Leveling
*3: w/ Navigation System
*4: w/ Network Gateway ECU
*5: w/o Network Gateway ECU
*6: w/ TOYOTA Parking Assist-sensor System and w/o Side Monitor System
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
NEXT
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
For vehicles with an SRS system:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
NEXT
Disconnect the E75 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E22-6 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E22-14 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
OK
NG
Reconnect the E75 No. 3 junction connector.
NEXT
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| w/ Network Gateway ECU | A |
| w/o Network Gateway ECU | B |
A
B
Disconnect the E72 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E22-6 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E22-14 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
OK
NG
For vehicles without dynamic headlight auto leveling, go to "Check for Short to GND in CAN Bus Wire (No. 1 Junction Connector - Center Airbag Sensor Assembly)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-3 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E72-14 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-4 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E72-15 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-2 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E72-13 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the E101 headlight swivel ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-3 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E72-14 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the E47 center airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-4 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E72-15 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the A38 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-2 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E72-13 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
| Result | Proceed to |
|---|---|
| OK (for 1GR-FE) | A |
| OK (for 1UZ-FE) | B |
| OK (for 3UR-FE) | C |
| OK (for 1VD-FTV) | D |
| NG | E |
A
B
C
D
E
Reconnect the E72 No. 1 junction connector.
NEXT
Disconnect the E69 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-1 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E69-12 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E22-6 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E22-14 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
OK
NG
For vehicles without a navigation system, go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - Air Conditioning Amplifier Assembly)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-2 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E69-13 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-5 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E69-16 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-3 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E69-14 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the F77 multi-media module receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-2 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E69-13 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the E35*1 or E81*2 air conditioning amplifier assembly connector.
*1: w/ Rear Air Conditioning System
*2: w/o Rear Air Conditioning System
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-5 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E69-16 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the E31 network gateway ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-3 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E69-14 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the E69 No. 2 junction connector.
NEXT
Disconnect the E75 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E75-1 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E75-12 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E75-4 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E75-15 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E75-3 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E75-14 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the E3 main body ECU (cowl side junction block LH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E75-4 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E75-15 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the E7 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E75-3 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E75-14 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
| Result | Proceed to |
|---|---|
| OK (w/ Multi-information Display) | A |
| OK (w/o Multi-information Display) | B |
| NG | C |
A
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/ Multi-information Display)>REMOVAL)
B
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/o Multi-information Display)>REMOVAL)
C
Disconnect the E72 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E22-6 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E22-14 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
OK
NG
For vehicles without an airbag system, go to "Check for Short to GND in CAN Bus Wire (No. 1 Junction Connector - 4WD Control ECU)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-4 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E72-15 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-5 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E72-16 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-2 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E72-13 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the E47 center airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-4 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E72-15 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the A27 4WD control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-5 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E72-16 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the A38 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-2 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E72-13 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
| Result | Proceed to |
|---|---|
| OK (for 1GR-FE) | A |
| OK (for 1UZ-FE) | B |
| OK (for 1VD-FTV) | C |
| NG | D |
A
B
C
D
Reconnect the E72 No. 1 junction connector.
NEXT
Disconnect the E69 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-1 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E69-12 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E22-6 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E22-14 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
OK
NG
For vehicles without a navigation system, go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - Air Conditioning Amplifier)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-2 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E69-13 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-5 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E69-16 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the F77 multi-media module receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-2 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E69-13 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the E35*1 or E81*2 air conditioning amplifier connector.
*1: w/ Rear Air Conditioning System
*2: w/o Rear Air Conditioning System
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-5 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E69-16 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the E69 No. 2 junction connector.
NEXT
Disconnect the F73 No. 6 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F73-7 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| F73-18 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 6 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E22-6 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E22-14 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
| Result | Proceed to |
|---|---|
| OK (w/ TOYOTA parking assist-sensor system) | A |
| OK (w/o TOYOTA parking assist-sensor system) | B |
| NG | C |
A
B
C
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F73-5 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| F73-16 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 6 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the F12 clearance warning ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F73-5 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| F73-16 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 6 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the F73 No. 6 junction connector.
NEXT
Disconnect the E75 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E75-1 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E75-12 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E75-4 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E75-15 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E75-5 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E75-16 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E75-3 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E75-14 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the E3 main body ECU (cowl side junction block LH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E75-4 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E75-15 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the A24 master cylinder solenoid (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E75-5 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E75-16 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the E7 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E75-3 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E75-14 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
| Result | Proceed to |
|---|---|
| OK (w/ Multi-information Display) | A |
| OK (w/o Multi-information Display) | B |
| NG | C |
A
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/ Multi-information Display)>REMOVAL)
B
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/o Multi-information Display)>REMOVAL)
C