Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  U1002 (CAN No. 2 BUS)  Lost Communication with Gateway Module (Network Gateway ECU)  


DESCRIPTION

·

The network gateway ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN movement control bus.

·

When the network gateway ECU receives a response signal from the ECUs connected to the CAN movement control bus, the network gateway ECU recognizes and memorizes that the ECU is connected to the CAN movement control bus. Based on this memorized data, the network gateway ECU monitors for malfunctions in the ECUs connected to the CAN movement control bus when communicating with those ECUs. If the network gateway ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN movement control bus, the network gateway ECU determines that a malfunction exists.

·

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).


DTC Code Symptoms Trouble Area
U1002 (CAN No. 2 BUS) Lost communication with the gateway module (network gateway ECU).
·

Movement control bus circuit

·

4WD control ECU CAN branch wire or connector

·

Power steering ECU assembly CAN branch wire or connector*1

·

Yaw rate sensor assembly CAN branch wire or connector*2

·

Distance control ECU assembly CAN branch wire or connector*3

·

Seat belt control ECU CAN branch wire or connector*4

·

Parking assist ECU CAN branch wire or connector*5

·

Clearance warning ECU assembly CAN branch wire or connector*6

·

Master cylinder solenoid (skid control ECU) CAN branch wire or connector

·

Steering angle sensor CAN branch wire or connector*2

·

Network gateway ECU CAN main wire or connector

·

Steering control ECU CAN branch wire or connector*7

·

Suspension control ECU CAN branch wire or connector*8

·

4WD control ECU

·

Power steering ECU assembly*1

·

Yaw rate sensor assembly*2

·

Distance control ECU assembly*3

·

Seat belt control ECU*4

·

Parking assist ECU*5

·

Clearance warning ECU assembly*6

·

Master cylinder solenoid (skid control ECU)

·

Steering angle sensor*2

·

Steering control ECU*7

·

Suspension control ECU*8

·

Network gateway ECU

·

No. 4 junction connector

·

No. 5 junction connector

·

No. 6 junction connector

·

No. 7 junction connector

·

No. 1 CAN junction connector



*1: for 1VD-FTV with DPF

*2: w/ Vehicle Stability Control System

*3: w/ Dynamic Radar Cruise Control System

*4: w/ Pre-crash Safety System

*5: w/ Side Monitor System

*6: w/ TOYOTA Parking Assist-sensor System and w/o Side Monitor System

*7: w/ Variable Gear Ratio Steering System

*8: w/ Active Height Control Suspension System

For vehicles with a network gateway ECU.


WIRING DIAGRAM

C259247E02
5.542,1.521 7.073,1.927 1.531,0.406 10 false Network Gateway ECU 5.865,0.438 6.385,0.677 0.521,0.24 10 false CA2H 5.542,1.365 5.885,1.573 0.344,0.208 10 false E31 3.854,0.448 4.125,0.729 0.271,0.281 10 false 2 3.854,0.906 4.135,1.146 0.281,0.24 10 false 13 5.875,1.094 6.354,1.323 0.479,0.229 10 false CA2L 0.271,1.521 1.615,1.781 1.344,0.26 10 false 4WD Control ECU 0.271,1.354 0.656,1.583 0.385,0.229 10 false A27 3.094,0.448 3.271,0.688 0.177,0.24 10 false 3 3.01,0.906 3.281,1.146 0.271,0.24 10 false 14 1.25,0.458 1.49,0.708 0.24,0.25 10 false 19 1.25,0.906 1.5,1.135 0.25,0.229 10 false 20 0.698,0.552 1.198,0.781 0.5,0.229 10 false CAN+ 0.719,1 1.188,1.26 0.469,0.26 10 false CAN- 2.75,3.24 4.49,3.583 1.74,0.344 10 false No. 4 Junction Connector 2.75,3.104 3.115,3.313 0.365,0.208 10 false E71 3.854,2.198 4.104,2.448 0.25,0.25 10 false 1 3.854,2.656 4.115,2.917 0.26,0.26 10 false 12 3.094,2.198 3.281,2.448 0.188,0.25 10 false 4 3.021,2.656 3.292,2.896 0.271,0.24 10 false 15 0.271,3.24 1.729,3.74 1.458,0.5 10 false Power Steering ECU Assembly*1 0.271,3.104 0.719,3.313 0.448,0.208 10 false E102 1.25,2.208 1.5,2.427 0.25,0.219 10 false 1 1.25,2.667 1.49,2.906 0.24,0.24 10 false 2 0.698,2.302 1.167,2.521 0.469,0.219 10 false CANH 0.719,2.75 1.198,2.979 0.479,0.229 10 false CANL 2.75,8.292 4.448,8.615 1.698,0.323 10 false No. 5 Junction Connector 2.75,8.156 3.104,8.365 0.354,0.208 10 false E68 3.854,5.802 4.052,5.969 0.198,0.167 10 false 4 3.854,6.26 4.094,6.49 0.24,0.229 10 false 15 3.854,7.292 4.052,7.521 0.198,0.229 10 false 2 3.854,7.75 4.104,7.969 0.25,0.219 10 false 13 3.094,5.802 3.271,6.042 0.177,0.24 10 false 5 3.021,6.26 3.271,6.51 0.25,0.25 10 false 16 0.271,6.865 1.948,7.188 1.677,0.323 10 false Seat Belt Control ECU*4 0.271,6.708 0.677,6.917 0.406,0.208 10 false E42 1.25,5.813 1.521,6.063 0.271,0.25 10 false 1 1.25,6.26 1.479,6.469 0.229,0.208 10 false 2 0.698,5.906 1.208,6.146 0.51,0.24 10 false CANH 0.719,6.354 1.188,6.573 0.469,0.219 10 false CANL 5.542,6.875 7.063,7.438 1.521,0.563 10 false Distance Control ECU Assembly*3 5.542,6.708 5.969,6.906 0.427,0.198 10 false E108 5.656,5.781 5.854,6.021 0.198,0.24 10 false 8 5.656,6.229 5.875,6.438 0.219,0.208 10 false 9 5.906,5.906 6.365,6.125 0.458,0.219 10 false CANH 5.906,6.354 6.354,6.583 0.448,0.229 10 false CANL 3.854,4.167 4.063,4.385 0.208,0.219 10 false 1 3.854,4.615 4.115,4.844 0.26,0.229 10 false 12 3.094,4.167 3.26,4.375 0.167,0.208 10 false 3 3.021,4.615 3.271,4.844 0.25,0.229 10 false 14 0.271,5.198 2.146,5.344 1.875,0.146 10 false Yaw Rate Sensor Assembly*2 0.271,5.063 0.625,5.229 0.354,0.167 10 false E50 1.25,4.177 1.448,4.385 0.198,0.208 10 false 3 1.25,4.625 1.469,4.833 0.219,0.208 10 false 2 0.688,4.281 1.177,4.469 0.49,0.188 10 false CANH 0.719,4.719 1.177,4.906 0.458,0.188 10 false CANL 5.594,0.427 5.833,0.635 0.24,0.208 10 false 13 5.594,0.906 5.865,1.104 0.271,0.198 10 false 12 0.104,7.344 2.083,7.604 1.979,0.26 10 false *1: for 1VD-FTV with DPF 0.104,7.615 2.646,7.906 2.542,0.292 10 false *2: w/ Vehicle Stability Control System 0.104,7.875 2.271,8.375 2.167,0.5 10 false *3: w/ Dynamic Radar Cruise Control System 0.104,8.458 2.26,8.792 2.156,0.333 10 false *4: w/ Pre-crash Safety System

C259248E01
3.822,0.522 3.920,0.693 0.098,0.170 10 7 3.822,0.937 3.998,1.107 0.176,0.170 10 18 3.036,0.537 3.134,0.707 0.098,0.170 10 5 2.958,0.951 3.134,1.121 0.176,0.170 10 16 1.24,0.537 1.417,0.707 0.177,0.170 10 40 1.24,0.951 1.417,1.121 0.177,0.170 10 39 0.661,0.64 1.079,0.777 0.418,0.137 10 CANH 0.684,1.048 1.079,1.185 0.396,0.137 10 CANL 0.267,1.578 1.640,1.726 1.372,0.148 10 Parking Assist ECU*5 0.267,1.44 0.570,1.609 0.303,0.169 10 F76 3.822,2.009 3.999,2.180 0.177,0.170 10 6 3.822,2.424 3.999,2.594 0.177,0.170 10 17 1.24,2.009 1.417,2.180 0.177,0.170 10 3 1.24,2.424 1.417,2.594 0.177,0.170 10 5 0.661,2.113 1.079,2.250 0.418,0.137 10 CANH 0.684,2.52 1.079,2.657 0.396,0.137 10 CANL 0.267,3.065 1.802,3.375 1.534,0.310 10 Clearance Warning ECU Assembly*6 0.267,2.912 0.570,3.081 0.303,0.169 10 F12 2.706,3.043 4.327,3.201 1.622,0.158 10 No. 6 Junction Connector 2.706,2.886 2.996,3.026 0.290,0.140 10 F73 2.706,7.873 4.327,8.031 1.622,0.158 10 No. 7 Junction Connector 5.186,9.221 7.118,9.378 1.932,0.158 10 No. 1 CAN Junction Connector 2.706,7.716 2.996,7.855 0.290,0.140 10 E74 1.24,3.771 1.417,3.941 0.177,0.170 10 9 1.24,4.213 1.417,4.383 0.177,0.170 10 20 0.661,3.874 1.079,4.011 0.418,0.137 10 CANH 0.684,4.324 1.079,4.461 0.396,0.137 10 CANL 0.267,4.798 1.802,5.108 1.534,0.310 10 Steering Control ECU*7 0.267,4.66 0.570,4.829 0.303,0.169 10 E79 3.822,3.771 4.022,3.941 0.200,0.170 10 2 3.822,4.213 4.022,4.383 0.200,0.170 10 13 3.037,3.771 3.134,3.941 0.097,0.170 10 3 2.961,4.213 3.134,4.383 0.172,0.170 10 14 5.619,5.718 5.726,5.888 0.107,0.170 10 9 5.549,5.276 5.725,5.446 0.177,0.170 10 10 5.873,5.379 6.291,5.516 0.418,0.137 10 CANH 5.873,5.828 6.268,5.965 0.396,0.137 10 CANL 5.524,6.303 7.067,6.469 1.543,0.166 10 Steering Angle Sensor*2 5.524,6.165 5.827,6.333 0.303,0.169 10 E11 1.24,5.276 1.417,5.446 0.177,0.170 10 11 1.24,5.718 1.417,5.888 0.177,0.170 10 25 0.661,5.379 1.079,5.516 0.418,0.137 10 CANH 0.684,5.828 1.079,5.965 0.396,0.137 10 CANL 0.267,6.303 1.864,6.613 1.597,0.310 10 Master Cylinder Solenoid (Skid Control ECU) 0.267,6.165 0.570,6.333 0.303,0.169 10 A24 3.822,5.276 4.022,5.446 0.200,0.170 10 4 3.822,5.718 4.022,5.888 0.200,0.170 10 15 3.037,5.276 3.134,5.446 0.097,0.170 10 5 2.961,5.718 3.134,5.888 0.172,0.170 10 16 4.332,8.341 4.509,8.511 0.177,0.170 10 7 4.332,8.783 4.509,8.954 0.177,0.170 10 8 3.752,8.444 4.171,8.581 0.418,0.137 10 CANH 3.775,8.894 4.171,9.031 0.396,0.137 10 CANL 3.266,9.368 4.971,9.516 1.706,0.148 10 Suspension Control ECU*8 3.266,9.23 3.569,9.399 0.303,0.169 10 K34 3.822,6.843 4.022,7.013 0.200,0.170 10 1 3.822,7.285 4.022,7.456 0.200,0.170 10 12 0.121,8.323 2.840,8.465 2.718,0.142 10 *5: w/ Side Monitor System 0.121,8.581 3.006,8.886 2.885,0.306 10 *6: w/ TOYOTA Parking Assist-sensor System and w/o Side Monitor System 0.121,9.18 3.006,9.322 2.885,0.142 10 *7: w/ Variable Gear Ratio Steering System 0.121,9.444 3.111,9.586 2.989,0.142 10 *8: w/ Active Height Control Suspension System 5.452,7.393 5.716,7.533 0.264,0.140 10 K29 5.536,7.203 5.633,7.342 0.097,0.140 10 2 5.452,6.946 5.716,7.085 0.264,0.140 10 K29 5.536,6.755 5.633,6.895 0.097,0.140 10 1 5.452,8.894 5.716,9.034 0.264,0.140 10 K39 5.536,8.704 5.633,8.844 0.097,0.140 10 2 5.452,8.447 5.716,8.587 0.264,0.140 10 K39 5.536,8.257 5.633,8.397 0.097,0.140 10 1 0.129,8.052 2.502,8.198 2.373,0.147 10 *2: w/ Vehicle Stability Control System

CAUTION / NOTICE / HINT

HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT CIRCUIT)
3.CHECK CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT CIRCUIT)
U165155E01
1.386,0.948 1.116,0.586 1.116,0.586 1.017,0.586 false 2.062,0.948 2.332,0.586 2.332,0.586 2.431,0.586 false 1.659,1.08 1.923,1.592 1.923,1.592 2.003,1.592 false 1.562,1.08 1.298,1.592 1.298,1.592 1.219,1.592 false 2.022,1.51 2.388,1.651 0.366,0.140 10 CA2L 0.733,1.51 1.124,1.651 0.390,0.140 10 CA2H 0.62,0.505 1.010,0.645 0.390,0.140 10 GND 2.452,0.505 2.842,0.645 0.390,0.140 10 BATT 0.063,0.042 0.369,0.182 0.306,0.140 10 *a 1.511,0.377 1.781,0.514 0.270,0.137 10 E31

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition Resistance Malfunction
E31-13 (CA2H) - E31-12 (CA2L) Ignition switch off 54 to 69 Ω Below 53 Ω: Short in line
E31-13 (CA2H) - E31-12 (CA2L) Ignition switch off 54 to 69 Ω 70 Ω or higher: Open in CAN main bus line
E31-13 (CA2H) - E31-2 (BATT) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
E31-12 (CA2L) - E31-2 (BATT) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
E31-13 (CA2H) - E31-4 (GND) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short
E31-12 (CA2L) - E31-4 (GND) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short


Text in Illustration
*a Component with harness connected
(Network Gateway ECU)

Result
Result Proceed to
NG
·

Open in CAN main wire


A
NG
·

Short in line

·

+B short

·

Ground short


B
OK C



A

4.CHECK FOR OPEN IN MAIN BUS WIRE (NO. 7 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

B

19.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR SIDE)

C

69.CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND)
4.CHECK FOR OPEN IN MAIN BUS WIRE (NO. 7 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
a.
U166199E01
0.447,2.262 0.711,2.398 0.264,0.136 10 E74 0.086,0.087 0.256,0.248 0.170,0.161 10 *a 2.6,2.64 2.998,2.779 0.397,0.139 10 CANL 2.647,1.941 3.067,2.080 0.420,0.139 10 CANH 2.149,2.438 2.349,2.724 2.349,2.724 2.584,2.724 false 2.153,2.215 2.434,2.012 2.434,2.012 2.622,2.012 false

Disconnect the E74 No. 7 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E74-2 (CANH) - E74-13 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 7 Junction Connector)



OK

5.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 7 JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

NG

6.CONNECT CONNECTOR
5.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 7 JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)
a.
U166200E01
0.447,2.262 0.711,2.398 0.264,0.136 10 E74 0.086,0.087 0.256,0.248 0.170,0.161 10 *a 2.686,2.568 3.083,2.707 0.397,0.139 10 CANL 2.737,1.961 3.158,2.100 0.420,0.139 10 CANH 2.26,2.438 2.434,2.652 2.434,2.652 2.669,2.652 false 2.264,2.215 2.473,2.033 2.473,2.033 2.713,2.033 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E74-1 (CANH) - E74-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 7 Junction Connector)



OK

REPLACE NO. 7 JUNCTION CONNECTOR

NG

15.CONNECT CONNECTOR
6.CONNECT CONNECTOR
a.

Reconnect the E74 No. 7 junction connector.



NEXT

7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
a.
U166201E01
0.447,2.263 0.711,2.399 0.264,0.136 10 F73 0.086,0.089 0.256,0.249 0.170,0.161 10 *a 2.222,2.809 2.619,2.948 0.397,0.139 10 CANL 2.561,1.65 2.981,1.789 0.420,0.139 10 CANH 1.723,2.44 1.97,2.893 1.97,2.893 2.205,2.893 false 1.727,2.217 2.348,1.722 2.348,1.722 2.537,1.722 false

Disconnect the F73 No. 6 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F73-6 (CANH) - F73-17 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)



OK

8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
a.
U166202E01
2.655,2.263 2.920,2.399 0.264,0.136 10 F73 0.086,0.089 0.256,0.249 0.170,0.161 10 *a 0.607,2.757 1.004,2.896 0.397,0.139 10 CANL 0.404,1.679 0.824,1.818 0.420,0.139 10 CANH 1.58,2.44 1.324,2.842 1.324,2.842 1.089,2.842 false 1.575,2.217 1.122,1.751 1.122,1.751 0.934,1.751 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F73-7 (CANH) - F73-18 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)



OK

REPLACE NO. 6 JUNCTION CONNECTOR

NG

9.CONNECT CONNECTOR
9.CONNECT CONNECTOR
a.

Reconnect the F73 No. 6 junction connector.



NEXT

10.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
10.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
a.
U166203E01
0.447,2.263 0.711,2.399 0.264,0.136 10 E68 0.086,0.089 0.256,0.249 0.170,0.161 10 *a 2.6,2.641 2.998,2.780 0.397,0.139 10 CANL 2.647,1.942 3.067,2.081 0.420,0.139 10 CANH 2.149,2.44 2.349,2.726 2.349,2.726 2.584,2.726 false 2.153,2.217 2.434,2.014 2.434,2.014 2.622,2.014 false

Disconnect the E68 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E68-2 (CANH) - E68-13 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)



OK

11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
a.
U166204E01
0.447,2.263 0.711,2.399 0.264,0.136 10 E68 0.086,0.089 0.256,0.249 0.170,0.161 10 *a 2.712,2.641 3.109,2.780 0.397,0.139 10 CANL 2.653,2.007 3.073,2.146 0.420,0.139 10 CANH 2.26,2.44 2.46,2.726 2.46,2.726 2.695,2.726 false 2.264,2.217 2.441,2.078 2.441,2.078 2.629,2.078 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E68-1 (CANH) - E68-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)



OK

REPLACE NO. 5 JUNCTION CONNECTOR

NG

12.CONNECT CONNECTOR
12.CONNECT CONNECTOR
a.

Reconnect the E68 No. 5 junction connector.



NEXT

13.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
13.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
a.
U166205E01
0.447,2.263 0.711,2.399 0.264,0.136 10 E71 0.086,0.089 0.256,0.249 0.170,0.161 10 *a 2.712,2.641 3.109,2.780 0.397,0.139 10 CANL 2.672,1.981 3.093,2.120 0.420,0.139 10 CANH 2.26,2.44 2.46,2.726 2.46,2.726 2.695,2.726 false 2.264,2.217 2.46,2.053 2.46,2.053 2.648,2.053 false

Disconnect the E71 No. 4 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E71-1 (CANH) - E71-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 4 Junction Connector)



OK

14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
a.
U166206E01
0.447,2.263 0.711,2.399 0.264,0.136 10 E71 0.086,0.089 0.256,0.249 0.170,0.161 10 *a 2.6,2.641 2.998,2.780 0.397,0.139 10 CANL 2.647,1.942 3.067,2.081 0.420,0.139 10 CANH 2.149,2.44 2.349,2.726 2.349,2.726 2.584,2.726 false 2.153,2.217 2.434,2.014 2.434,2.014 2.622,2.014 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E71-2 (CANH) - E71-13 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 4 Junction Connector)



OK

REPLACE NO. 4 JUNCTION CONNECTOR

NG

17.CONNECT CONNECTOR
15.CONNECT CONNECTOR
a.

Reconnect the E74 No. 7 junction connector.



NEXT

16.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 CAN JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
16.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 CAN JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
a.
U165371E01
1.888,1.343 2.098,1.139 2.098,1.139 2.267,1.139 false 1.888,1.499 2.058,1.683 2.058,1.683 2.227,1.683 false 2.285,1.062 2.700,1.209 0.415,0.147 10 CANH 2.244,1.606 2.659,1.752 0.415,0.147 10 CANL 0.079,0.057 0.494,0.204 0.415,0.147 10 *a 0.941,1.288 1.208,1.427 0.267,0.140 10 K29

Disconnect the K29 No. 1 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
K29-1 (CANH) - K29-2 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

17.CONNECT CONNECTOR
a.

Reconnect the E71 No. 4 junction connector.



NEXT

18.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NETWORK GATEWAY ECU - NO. 4 JUNCTION CONNECTOR)
18.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NETWORK GATEWAY ECU - NO. 4 JUNCTION CONNECTOR)
a.
U165158E01
2.784,1.121 3.057,1.259 0.273,0.137 10 E31 1.599,1.295 1.216,1.633 1.216,1.633 1.093,1.633 false 1.434,1.919 1.58,1.919 1.58,1.919 1.707,1.293 false 0.603,1.558 0.992,1.696 0.389,0.137 10 CA2H 0.984,1.833 1.373,1.971 0.389,0.137 10 CA2L 0.07,0.056 0.371,0.193 0.301,0.137 10 *a

Disconnect the E31 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E31-13 (CA2H) - E31-12 (CA2L) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO NETWORK GATEWAY ECU (NETWORK GATEWAY ECU - NO. 4 JUNCTION CONNECTOR)

19.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR SIDE)
a.
U165155E01
1.386,0.948 1.116,0.586 1.116,0.586 1.017,0.586 false 2.062,0.948 2.332,0.586 2.332,0.586 2.431,0.586 false 1.659,1.08 1.923,1.592 1.923,1.592 2.003,1.592 false 1.562,1.08 1.298,1.592 1.298,1.592 1.219,1.592 false 2.022,1.51 2.388,1.651 0.366,0.140 10 CA2L 0.733,1.51 1.124,1.651 0.390,0.140 10 CA2H 0.62,0.505 1.010,0.645 0.390,0.140 10 GND 2.452,0.505 2.842,0.645 0.390,0.140 10 BATT 0.063,0.042 0.369,0.182 0.306,0.140 10 *a 1.511,0.377 1.781,0.514 0.270,0.137 10 E31

Disconnect the E74 No. 7 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E31-13 (CA2H) - E31-12 (CA2L) Ignition switch off 108 to 132 Ω
E31-13 (CA2H) - E31-4 (GND) Ignition switch off 200 Ω or higher
E31-12 (CA2L) - E31-4 (GND) Ignition switch off 200 Ω or higher
E31-13 (CA2H) - E31-2 (BATT) Ignition switch off 6 kΩ or higher
E31-12 (CA2L) - E31-2 (BATT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Component with harness connected
(Network Gateway ECU)



OK

20.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - STEERING CONTROL ECU)

NG

24.CONNECT CONNECTOR
20.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - STEERING CONTROL ECU)
NOTICE:

For vehicles without a variable gear ratio steering system, go to "Check for Short in CAN Bus Wires (No. 7 Junction Connector - Steering Angle Sensor)".


a.
U165343E02
2,1.115 2.302,0.854 2.302,0.854 2.479,0.854 false 2.021,1.281 2.281,1.594 2.281,1.594 2.448,1.594 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.51,0.781 3.021,0.99 0.51,0.208 10 false CANH 2.5,1.51 3.01,1.719 0.51,0.208 10 false CANL 2.583,3.094 3.042,3.333 0.458,0.24 10 false BAT 0.917,2.052 1.208,2.26 0.292,0.208 10 false CG 0.063,0.063 0.448,0.302 0.385,0.24 10 false *a 0.052,1.823 0.469,2.042 0.417,0.219 10 false *b 0.583,1.104 0.927,1.323 0.344,0.219 10 false E74 0.427,2.656 0.792,2.865 0.365,0.208 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E74-3 (CANH) - E74-14 (CANL) Ignition switch off 200 Ω or higher
E74-3 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E74-14 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E74-3 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E74-14 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 7 Junction Connector)
*b Front view of DLC3



OK

21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

NG

40.CONNECT CONNECTOR
21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)
NOTICE:

For vehicles without a vehicle stability control system, go to "Check for Short in CAN Bus Wires (No. 7 Junction Connector - Skid Control ECU)".


a.
U165344E02
1.896,1.104 2.292,0.771 2.292,0.771 2.469,0.771 false 1.917,1.281 2.104,1.635 2.104,1.635 2.281,1.635 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.5,0.688 3.042,0.917 0.542,0.229 10 false CANH 2.323,1.563 2.802,1.76 0.479,0.198 10 false CANL 2.604,3.094 3.083,3.323 0.479,0.229 10 false BAT 0.917,2.052 1.271,2.271 0.354,0.219 10 false CG 0.063,0.063 0.49,0.271 0.427,0.208 10 false *a 0.063,1.823 0.479,2.021 0.417,0.198 10 false *b 0.583,1.104 0.938,1.302 0.354,0.198 10 false E74 0.438,2.677 0.792,2.854 0.354,0.177 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E74-4 (CANH) - E74-15 (CANL) Ignition switch off 200 Ω or higher
E74-4 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E74-15 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E74-4 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E74-15 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 7 Junction Connector)
*b Front view of DLC3



OK

22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - SKID CONTROL ECU)

NG

42.CONNECT CONNECTOR
22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - SKID CONTROL ECU)
a.
U165345E02
1.802,1.104 2.365,0.635 2.365,0.635 2.531,0.635 false 1.823,1.281 2.167,1.677 2.167,1.677 2.333,1.677 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.573,0.552 3.083,0.781 0.51,0.229 10 false CANH 2.385,1.604 2.875,1.865 0.49,0.26 10 false CANL 2.615,3.094 3.073,3.313 0.458,0.219 10 false BAT 0.917,2.052 1.208,2.25 0.292,0.198 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.594,1.104 0.948,1.302 0.354,0.198 10 false E74 0.427,2.677 0.802,2.875 0.375,0.198 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E74-5 (CANH) - E74-16 (CANL) Ignition switch off 200 Ω or higher
E74-5 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E74-16 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E74-5 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E74-16 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 7 Junction Connector)
*b Front view of DLC3



OK

23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

NG

44.CONNECT CONNECTOR
23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)
a.
U165346E02
2.188,1.104 2.385,0.917 2.385,0.917 2.552,0.917 false 2.219,1.281 2.406,1.521 2.406,1.521 2.573,1.521 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.604,0.833 3.104,1.042 0.5,0.208 10 false CANH 2.615,1.448 3.135,1.698 0.521,0.25 10 false CANL 2.594,3.094 3.094,3.323 0.5,0.229 10 false BAT 0.917,2.052 1.208,2.25 0.292,0.198 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.604,1.104 0.938,1.313 0.333,0.208 10 false E74 0.427,2.677 0.771,2.896 0.344,0.219 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E74-1 (CANH) - E74-12 (CANL) Ignition switch off 108 to 132 Ω
E74-1 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E74-12 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E74-1 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E74-12 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 7 Junction Connector)
*b Front view of DLC3

Result
Result Proceed to
OK A
NG (w/ Active Height Control Suspension) B
NG (w/o Active Height Control Suspension) C



A

REPLACE NO. 7 JUNCTION CONNECTOR

B

46.CONNECT CONNECTOR

C

51.CONNECT CONNECTOR
24.CONNECT CONNECTOR
a.

Reconnect the E74 No. 7 junction connector.



NEXT

25.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
25.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
a.
U165347E02
1.719,1.104 2.281,0.635 2.281,0.635 2.448,0.635 false 1.729,1.281 2.073,1.677 2.073,1.677 2.24,1.677 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.479,0.552 2.979,0.792 0.5,0.24 10 false CANH 2.292,1.604 2.823,1.844 0.531,0.24 10 false CANL 2.604,3.094 3.094,3.323 0.49,0.229 10 false BAT 0.917,2.052 1.208,2.25 0.292,0.198 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.604,1.104 0.948,1.313 0.344,0.208 10 false F73 0.417,2.667 0.771,2.885 0.354,0.219 10 false E22

Disconnect the F73 No. 6 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F73-6 (CANH) - F73-17 (CANL) Ignition switch off 108 to 132 Ω
F73-6 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
F73-17 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
F73-6 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
F73-17 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)
*b Front view of DLC3



OK

26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR SIDE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR SIDE)
a.
U165155E01
1.386,0.948 1.116,0.586 1.116,0.586 1.017,0.586 false 2.062,0.948 2.332,0.586 2.332,0.586 2.431,0.586 false 1.659,1.08 1.923,1.592 1.923,1.592 2.003,1.592 false 1.562,1.08 1.298,1.592 1.298,1.592 1.219,1.592 false 2.022,1.51 2.388,1.651 0.366,0.140 10 CA2L 0.733,1.51 1.124,1.651 0.390,0.140 10 CA2H 0.62,0.505 1.010,0.645 0.390,0.140 10 GND 2.452,0.505 2.842,0.645 0.390,0.140 10 BATT 0.063,0.042 0.369,0.182 0.306,0.140 10 *a 1.511,0.377 1.781,0.514 0.270,0.137 10 E31

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E31-13 (CA2H) - E31-12 (CA2L) Ignition switch off 108 to 132 Ω
E31-13 (CA2H) - E31-4 (GND) Ignition switch off 200 Ω or higher
E31-12 (CA2L) - E31-4 (GND) Ignition switch off 200 Ω or higher
E31-13 (CA2H) - E31-2 (BATT) Ignition switch off 6 kΩ or higher
E31-12 (CA2L) - E31-2 (BATT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Component with harness connected
(Network Gateway ECU)

Result
Result Proceed to
OK (w/o TOYOTA Parking Assist-sensor System and w/o Side Monitor System) A
OK (w/ TOYOTA Parking Assist-sensor System and w/o Side Monitor System) B
OK (w/ Side Monitor System) C
NG D



A

REPLACE NO. 6 JUNCTION CONNECTOR

B

27.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)

C

28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - PARKING ASSIST ECU)

D

29.CONNECT CONNECTOR
27.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)
a.
U165348E02
1.813,1.104 2.271,0.635 2.271,0.635 2.438,0.635 false 1.833,1.281 2.073,1.677 2.073,1.677 2.24,1.677 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.479,0.563 2.969,0.75 0.49,0.188 10 false CANH 2.281,1.604 2.792,1.833 0.51,0.229 10 false CANL 2.615,3.094 3.083,3.323 0.469,0.229 10 false BAT 0.917,2.052 1.208,2.229 0.292,0.177 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.604,1.104 0.917,1.292 0.313,0.188 10 false F73 0.417,2.667 0.75,2.865 0.333,0.198 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F73-5 (CANH) - F73-16 (CANL) Ignition switch off 200 Ω or higher
F73-5 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
F73-16 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
F73-5 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
F73-16 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 6 JUNCTION CONNECTOR

NG

53.CONNECT CONNECTOR
28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - PARKING ASSIST ECU)
a.
U165348E02
1.813,1.104 2.271,0.635 2.271,0.635 2.438,0.635 false 1.833,1.281 2.073,1.677 2.073,1.677 2.24,1.677 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.479,0.563 2.969,0.75 0.49,0.188 10 false CANH 2.281,1.604 2.792,1.833 0.51,0.229 10 false CANL 2.615,3.094 3.083,3.323 0.469,0.229 10 false BAT 0.917,2.052 1.208,2.229 0.292,0.177 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.604,1.104 0.917,1.292 0.313,0.188 10 false F73 0.417,2.667 0.75,2.865 0.333,0.198 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F73-5 (CANH) - F73-16 (CANL) Ignition switch off 200 Ω or higher
F73-5 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
F73-16 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
F73-5 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
F73-16 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 6 JUNCTION CONNECTOR

NG

55.CONNECT CONNECTOR
29.CONNECT CONNECTOR
a.

Reconnect the F73 No. 6 junction connector.



NEXT

30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
a.
U165349E02
2.094,1.115 2.354,0.896 2.354,0.896 2.531,0.896 false 2.115,1.281 2.26,1.552 2.26,1.552 2.427,1.552 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.573,0.823 3.052,1.021 0.479,0.198 10 false CANH 2.458,1.479 2.948,1.719 0.49,0.24 10 false CANL 2.604,3.094 3.094,3.302 0.49,0.208 10 false BAT 0.917,2.052 1.219,2.229 0.302,0.177 10 false CG 0.063,0.063 0.469,0.271 0.406,0.208 10 false *a 0.073,1.844 0.49,2.073 0.417,0.229 10 false *b 0.583,1.104 0.938,1.323 0.354,0.219 10 false E68 0.427,2.667 0.823,2.875 0.396,0.208 10 false E22

Disconnect the E68 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E68-2 (CANH) - E68-13 (CANL) Ignition switch off 108 to 132 Ω
E68-2 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E68-13 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E68-2 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E68-13 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)
*b Front view of DLC3



OK

31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR SIDE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR SIDE)
a.
U165155E01
1.386,0.948 1.116,0.586 1.116,0.586 1.017,0.586 false 2.062,0.948 2.332,0.586 2.332,0.586 2.431,0.586 false 1.659,1.08 1.923,1.592 1.923,1.592 2.003,1.592 false 1.562,1.08 1.298,1.592 1.298,1.592 1.219,1.592 false 2.022,1.51 2.388,1.651 0.366,0.140 10 CA2L 0.733,1.51 1.124,1.651 0.390,0.140 10 CA2H 0.62,0.505 1.010,0.645 0.390,0.140 10 GND 2.452,0.505 2.842,0.645 0.390,0.140 10 BATT 0.063,0.042 0.369,0.182 0.306,0.140 10 *a 1.511,0.377 1.781,0.514 0.270,0.137 10 E31

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E31-13 (CA2H) - E31-12 (CA2L) Ignition switch off 108 to 132 Ω
E31-13 (CA2H) - E31-4 (GND) Ignition switch off 200 Ω or higher
E31-12 (CA2L) - E31-4 (GND) Ignition switch off 200 Ω or higher
E31-13 (CA2H) - E31-2 (BATT) Ignition switch off 6 kΩ or higher
E31-12 (CA2L) - E31-2 (BATT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Component with harness connected
(Network Gateway ECU)



OK

32.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - DISTANCE CONTROL ECU ASSEMBLY)

NG

35.CONNECT CONNECTOR
32.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - DISTANCE CONTROL ECU ASSEMBLY)
NOTICE:

For vehicles without a dynamic radar cruise control system, go to "Check for Short in CAN Bus Wires (No. 5 Junction Connector - Seat Belt Control ECU)".


a.
U165350E02
1.896,1.115 2.313,0.823 2.313,0.823 2.479,0.823 false 1.906,1.281 2.135,1.615 2.135,1.615 2.302,1.615 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.51,0.75 2.99,1.01 0.479,0.26 10 false CANH 2.323,1.531 2.854,1.813 0.531,0.281 10 false CANL 2.583,3.094 3.073,3.333 0.49,0.24 10 false BAT 0.917,2.052 1.219,2.25 0.302,0.198 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.583,1.104 0.948,1.292 0.365,0.188 10 false E68 0.427,2.667 0.802,2.906 0.375,0.24 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E68-4 (CANH) - E68-15 (CANL) Ignition switch off 200 Ω or higher
E68-4 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E68-15 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E68-4 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E68-15 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)
*b Front view of DLC3



OK

33.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - SEAT BELT CONTROL ECU)

NG

57.CONNECT CONNECTOR
33.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - SEAT BELT CONTROL ECU)
NOTICE:

For vehicles without a pre-crash safety system, go to "Check for Short in CAN Bus Wires (No. 5 Junction Connector - Yaw Rate Sensor Assembly)".


a.
U165351E02
1.813,1.104 2.271,0.635 2.271,0.635 2.438,0.635 false 1.833,1.281 2.073,1.677 2.073,1.677 2.24,1.677 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.5,0.563 3.021,0.792 0.521,0.229 10 false CANH 2.281,1.604 2.771,1.906 0.49,0.302 10 false CANL 2.583,3.094 3.094,3.302 0.51,0.208 10 false BAT 0.917,2.052 1.292,2.292 0.375,0.24 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.583,1.104 0.969,1.302 0.385,0.198 10 false E68 0.438,2.677 0.802,2.875 0.365,0.198 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E68-5 (CANH) - E68-16 (CANL) Ignition switch off 200 Ω or higher
E68-5 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E68-16 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E68-5 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E68-16 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)
*b Front view of DLC3



OK

34.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)

NG

59.CONNECT CONNECTOR
34.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)
NOTICE:

For vehicles without a vehicle stability control system, replace No. 5 junction connector.


a.
U165352E02
2,1.104 2.354,0.771 2.354,0.771 2.521,0.771 false 2.021,1.281 2.313,1.625 2.313,1.625 2.479,1.625 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.552,0.698 3.073,0.906 0.521,0.208 10 false CANH 2.521,1.542 2.99,1.771 0.469,0.229 10 false CANL 2.604,3.094 3.073,3.292 0.469,0.198 10 false BAT 0.917,2.052 1.208,2.25 0.292,0.198 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.583,1.104 0.896,1.302 0.313,0.198 10 false E68 0.427,2.656 0.781,2.854 0.354,0.198 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E68-3 (CANH) - E68-14 (CANL) Ignition switch off 200 Ω or higher
E68-3 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E68-14 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E68-3 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E68-14 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 5 JUNCTION CONNECTOR

NG

61.CONNECT CONNECTOR
35.CONNECT CONNECTOR
a.

Reconnect the E68 No. 5 junction connector.



NEXT

36.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
36.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
a.
U165353E02
2.188,1.104 2.375,0.938 2.375,0.938 2.552,0.938 false 2.208,1.281 2.354,1.469 2.354,1.469 2.521,1.469 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.604,0.854 3.104,1.073 0.5,0.219 10 false CANH 2.563,1.396 3.052,1.615 0.49,0.219 10 false CANL 2.583,3.094 3,3.313 0.417,0.219 10 false BAT 0.917,2.052 1.219,2.26 0.302,0.208 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.604,1.104 0.958,1.313 0.354,0.208 10 false E71 0.427,2.677 0.813,2.896 0.385,0.219 10 false E22

Disconnect the E71 No. 4 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E71-1 (CANH) - E71-12 (CANL) Ignition switch off 108 to 132 Ω
E71-1 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E71-12 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E71-1 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E71-12 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 4 Junction Connector)
*b Front view of DLC3

Result
Result Proceed to
OK (for 1VD-FTV with DPF) A
OK (except 1VD-FTV with DPF) B
NG C



A

37.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

B

38.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - 4WD CONTROL ECU)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

37.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.
U165354E02
1.896,1.115 2.354,0.781 2.354,0.781 2.521,0.781 false 1.917,1.281 2.156,1.625 2.156,1.625 2.323,1.625 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.563,0.708 3.073,0.948 0.51,0.24 10 false CANH 2.344,1.552 2.938,1.771 0.594,0.219 10 false CANL 2.604,3.094 3.073,3.323 0.469,0.229 10 false BAT 0.917,2.052 1.25,2.25 0.333,0.198 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.604,1.104 0.927,1.302 0.323,0.198 10 false E71 0.417,2.667 0.771,2.875 0.354,0.208 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E71-4 (CANH) - E71-15 (CANL) Ignition switch off 200 Ω or higher
E71-4 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E71-15 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E71-4 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E71-15 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 4 Junction Connector)
*b Front view of DLC3



OK

38.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - 4WD CONTROL ECU)

NG

63.CONNECT CONNECTOR
38.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - 4WD CONTROL ECU)
a.
U165355E02
2,1.104 2.354,0.771 2.354,0.771 2.521,0.771 false 2.021,1.281 2.313,1.625 2.313,1.625 2.479,1.625 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.552,0.688 3.083,0.896 0.531,0.208 10 false CANH 2.51,1.552 3.083,1.792 0.573,0.24 10 false CANL 2.604,3.094 3.052,3.323 0.448,0.229 10 false BAT 0.917,2.052 1.271,2.24 0.354,0.188 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.604,1.104 0.938,1.313 0.333,0.208 10 false E71 0.427,2.667 0.813,2.865 0.385,0.198 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E71-3 (CANH) - E71-14 (CANL) Ignition switch off 200 Ω or higher
E71-3 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E71-14 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E71-3 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E71-14 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 4 Junction Connector)
*b Front view of DLC3



OK

39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

NG

65.CONNECT CONNECTOR
39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
a.
U165356E02
2.094,1.115 2.385,0.875 2.385,0.875 2.552,0.875 false 2.104,1.281 2.354,1.521 2.354,1.521 2.521,1.521 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.583,0.792 3.167,1.042 0.583,0.25 10 false CANH 2.563,1.448 3.073,1.698 0.51,0.25 10 false CANL 2.604,3.094 3.135,3.313 0.531,0.219 10 false BAT 0.917,2.052 1.219,2.25 0.302,0.198 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.615,1.104 0.979,1.292 0.365,0.188 10 false E71 0.427,2.667 0.771,2.854 0.344,0.188 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E71-2 (CANH) - E71-13 (CANL) Ignition switch off 108 to 132 Ω
E71-2 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E71-13 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E71-2 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E71-13 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 4 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 4 JUNCTION CONNECTOR

NG

67.CONNECT CONNECTOR
40.CONNECT CONNECTOR
a.

Reconnect the E74 No. 7 junction connector.



NEXT

41.CHECK FOR SHORT IN CAN BUS WIRES (STEERING CONTROL ECU)
41.CHECK FOR SHORT IN CAN BUS WIRES (STEERING CONTROL ECU)
a.
U165125E02
1.385,2.073 1.5,2.073 1.5,2.073 1.656,2.365 false 2.219,2.823 2.438,3.042 2.438,3.042 2.563,3.042 false 0.917,1.563 0.76,1.344 0.76,1.344 0.667,1.344 false 0.604,1.073 0.729,1.073 0.729,1.073 0.917,1.479 false 1.719,1.427 2.063,1.656 0.344,0.229 10 false E79 1.115,2 1.354,2.146 0.24,0.146 10 false CG 0.094,0.969 0.604,1.156 0.51,0.188 10 false CANH 0.198,1.26 0.646,1.458 0.448,0.198 10 false CANL 2.583,2.958 3.021,3.188 0.438,0.229 10 false BAT 0.375,2.563 0.76,2.771 0.385,0.208 10 false E22 0.073,0.063 0.271,0.26 0.198,0.198 10 false *a 0.073,1.927 0.271,2.125 0.198,0.198 10 false *b

Disconnect the E79 steering control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E79-9 (CANH) - E79-20 (CANL) Ignition switch off 54 to 69 Ω
E79-9 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E79-20 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E79-9 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E79-20 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Steering Control ECU)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING CONTROL ECU (CANH, CANL)

42.CONNECT CONNECTOR
a.

Reconnect the E74 No. 7 junction connector.



NEXT

43.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)
43.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)
a.
U165298E02
2.188,2.885 2.365,3.146 2.365,3.146 2.51,3.146 false 1.594,2.406 1.365,2.073 1.365,2.073 1.219,2.073 false 2.208,1.344 1.948,1.698 1.948,1.698 1.833,1.698 false 2.354,1.344 2.604,1.698 2.604,1.698 2.719,1.698 false 0.063,1.844 0.25,1.99 0.188,0.146 10 false *b 0.063,0.052 0.25,0.198 0.188,0.146 10 false *a 0.354,2.563 0.708,2.76 0.354,0.198 10 false E22 0.906,1.99 1.24,2.188 0.333,0.198 10 false CG 2.594,3.052 3.021,3.271 0.427,0.219 10 false BAT 0.333,1.052 0.698,1.271 0.365,0.219 10 false E11 1.344,1.615 1.823,1.844 0.479,0.229 10 false CANL 2.75,1.615 3.26,1.854 0.51,0.24 10 false CANH

Disconnect the E11 steering angle sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E11-10 (CANH) - E11-9 (CANL) Ignition switch off 54 to 69 Ω
E11-10 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E11-9 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E11-10 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E11-9 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)

44.CONNECT CONNECTOR
a.

Reconnect the E74 No. 7 junction connector.



NEXT

45.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)
45.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)
a.
U165299E02
2.177,2.885 2.354,3.146 2.354,3.146 2.5,3.146 false 1.573,2.406 1.344,2.073 1.344,2.073 1.198,2.073 false 1.958,1.094 2.333,0.74 2.333,0.74 2.448,0.74 false 1.969,1.188 2.208,1.583 2.208,1.583 2.323,1.583 false 0.063,1.844 0.344,2.052 0.281,0.208 10 false *b 0.063,0.052 0.333,0.26 0.271,0.208 10 false *a 0.385,2.563 0.781,2.75 0.396,0.188 10 false E22 0.875,1.99 1.208,2.208 0.333,0.219 10 false CG 2.552,3.073 3.01,3.323 0.458,0.25 10 false BAT 0.406,1.094 0.729,1.26 0.323,0.167 10 false A24 2.49,0.656 3.042,0.917 0.552,0.26 10 false CANH 2.365,1.51 2.938,1.76 0.573,0.25 10 false CANL

Disconnect the A24 master cylinder solenoid (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A24-11 (CANH) - A24-25 (CANL) Ignition switch off 54 to 69 Ω
A24-11 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
A24-25 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
A24-11 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
A24-25 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])
*b Front view of DLC3



OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

46.CONNECT CONNECTOR
a.

Reconnect the E74 No. 7 junction connector.



NEXT

47.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - SUSPENSION CONTROL ECU)
47.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - SUSPENSION CONTROL ECU)
a.
U165372E01
1.827,1.283 1.997,1.133 1.997,1.133 2.166,1.133 false 1.824,1.415 1.947,1.584 1.947,1.584 2.116,1.584 false 2.216,2.956 2.393,3.174 2.393,3.174 2.562,3.174 false 2.183,1.056 2.598,1.203 0.415,0.147 10 CANH 2.133,1.506 2.548,1.653 0.415,0.147 10 CANL 2.579,3.097 2.994,3.243 0.415,0.147 10 BAT 0.915,2.057 1.147,2.204 0.232,0.147 10 CG 0.058,0.066 0.473,0.213 0.415,0.147 10 *a 0.058,1.828 0.473,1.974 0.415,0.147 10 *b 0.947,1.243 1.214,1.383 0.267,0.140 10 K39 0.4,2.676 0.667,2.815 0.267,0.140 10 E22 1.661,2.517 1.378,2.136 1.378,2.136 1.209,2.136 false

Disconnect the K39 No. 1 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
K39-1 (CANH) - K39-2 (CANL) Ignition switch off 200 Ω or higher
K39-1 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
K39-2 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
K39-1 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
K39-2 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b Front view of DLC3



OK

48.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR)

NG

49.CONNECT CONNECTOR
48.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR)
a.
U165373E01
1.827,1.283 1.997,1.133 1.997,1.133 2.166,1.133 false 1.824,1.415 1.947,1.584 1.947,1.584 2.116,1.584 false 2.216,2.956 2.393,3.174 2.393,3.174 2.562,3.174 false 2.183,1.056 2.598,1.203 0.415,0.147 10 CANH 2.133,1.506 2.548,1.653 0.415,0.147 10 CANL 2.579,3.097 2.994,3.243 0.415,0.147 10 BAT 0.915,2.057 1.147,2.204 0.232,0.147 10 CG 0.058,0.066 0.473,0.213 0.415,0.147 10 *a 0.058,1.828 0.473,1.974 0.415,0.147 10 *b 0.947,1.243 1.214,1.383 0.267,0.140 10 K29 0.4,2.676 0.667,2.815 0.267,0.140 10 E22 1.661,2.517 1.378,2.136 1.378,2.136 1.209,2.136 false

Disconnect the K29 No. 1 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
K29-1 (CANH) - K29-2 (CANL) Ignition switch off 108 to 132 Ω
K29-1 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
K29-2 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
K29-1 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
K29-2 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

49.CONNECT CONNECTOR
a.

Reconnect the K39 No. 1 CAN junction connector.



NEXT

50.CHECK FOR SHORT IN CAN BUS WIRES (SUSPENSION CONTROL ECU)
50.CHECK FOR SHORT IN CAN BUS WIRES (SUSPENSION CONTROL ECU)
a.
U165300E02
2.188,2.885 2.365,3.146 2.365,3.146 2.51,3.146 false 1.573,2.406 1.344,2.073 1.344,2.073 1.198,2.073 false 2.156,1.146 2.396,1.344 2.396,1.344 2.51,1.344 false 2.073,1.146 2.25,1.573 2.25,1.573 2.396,1.573 false 0.063,1.844 0.25,1.99 0.188,0.146 10 false *b 0.063,0.052 0.25,0.198 0.188,0.146 10 false *a 0.396,2.563 0.75,2.771 0.354,0.208 10 false E22 0.906,1.99 1.219,2.198 0.313,0.208 10 false CG 2.563,3.052 2.948,3.281 0.385,0.229 10 false BAT 0.521,1 0.875,1.208 0.354,0.208 10 false K34 2.542,1.271 3.063,1.5 0.521,0.229 10 false CANH 2.417,1.49 2.885,1.677 0.469,0.188 10 false CANL

Disconnect the K34 suspension control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
K34-7 (CANH) - K34-8 (CANL) Ignition switch off 54 to 69 Ω
K34-7 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
K34-8 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
K34-7 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
K34-8 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Suspension Control ECU)
*b Front view of DLC3



OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SUSPENSION CONTROL ECU (CANH, CANL)

51.CONNECT CONNECTOR
a.

Reconnect the E74 No. 7 junction connector.



NEXT

52.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR)
52.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR)
a.
U165373E01
1.827,1.283 1.997,1.133 1.997,1.133 2.166,1.133 false 1.824,1.415 1.947,1.584 1.947,1.584 2.116,1.584 false 2.216,2.956 2.393,3.174 2.393,3.174 2.562,3.174 false 2.183,1.056 2.598,1.203 0.415,0.147 10 CANH 2.133,1.506 2.548,1.653 0.415,0.147 10 CANL 2.579,3.097 2.994,3.243 0.415,0.147 10 BAT 0.915,2.057 1.147,2.204 0.232,0.147 10 CG 0.058,0.066 0.473,0.213 0.415,0.147 10 *a 0.058,1.828 0.473,1.974 0.415,0.147 10 *b 0.947,1.243 1.214,1.383 0.267,0.140 10 K29 0.4,2.676 0.667,2.815 0.267,0.140 10 E22 1.661,2.517 1.378,2.136 1.378,2.136 1.209,2.136 false

Disconnect the K29 No. 1 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
K29-1 (CANH) - K29-2 (CANL) Ignition switch off 108 to 132 Ω
K29-1 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
K29-2 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
K29-1 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
K29-2 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

53.CONNECT CONNECTOR
a.

Reconnect the F73 No. 6 junction connector.



NEXT

54.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
54.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.
U165301E02
2.177,2.885 2.354,3.146 2.354,3.146 2.5,3.146 false 1.583,2.406 1.354,2.073 1.354,2.073 1.208,2.073 false 1.167,1.073 0.854,0.771 0.854,0.771 0.74,0.771 false 1.396,1.073 1.146,0.479 1.146,0.479 1.031,0.479 false 0.063,1.844 0.365,2.052 0.302,0.208 10 false *b 0.063,0.052 0.313,0.26 0.25,0.208 10 false *a 0.396,2.563 0.729,2.75 0.333,0.188 10 false E22 0.917,1.99 1.229,2.198 0.313,0.208 10 false CG 2.563,3.052 2.938,3.25 0.375,0.198 10 false BAT 2.875,1.083 3.208,1.281 0.333,0.198 10 false F12 0.219,0.688 0.719,0.885 0.5,0.198 10 false CANH 0.563,0.396 1.021,0.583 0.458,0.188 10 false CANL

Disconnect the F12 clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F12-3 (CANH) - F12-5 (CANL) Ignition switch off 54 to 69 Ω
F12-3 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
F12-5 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
F12-3 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
F12-5 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CLEARANCE WARNING ECU ASSEMBLY (CANH, CANL)

55.CONNECT CONNECTOR
a.

Reconnect the F73 No. 6 junction connector.



NEXT

56.CHECK FOR SHORT IN CAN BUS WIRES (PARKING ASSIST ECU)
56.CHECK FOR SHORT IN CAN BUS WIRES (PARKING ASSIST ECU)
a.
U165302E02
2.177,2.885 2.354,3.146 2.354,3.146 2.5,3.146 false 1.583,2.406 1.354,2.073 1.354,2.073 1.208,2.073 false 1,1.042 0.865,1.417 0.865,1.417 0.708,1.417 false 0.938,1.042 0.844,1.135 0.844,1.135 0.656,1.135 false 0.063,1.844 0.344,2.052 0.281,0.208 10 false *b 0.063,0.052 0.344,0.281 0.281,0.229 10 false *a 0.385,2.563 0.76,2.771 0.375,0.208 10 false E22 0.917,1.99 1.25,2.208 0.333,0.219 10 false CG 2.594,3.052 3.01,3.24 0.417,0.188 10 false BAT 2.927,0.896 3.25,1.083 0.323,0.188 10 false F76 0.188,1.344 0.688,1.563 0.5,0.219 10 false CANL 0.135,1.052 0.615,1.25 0.479,0.198 10 false CANH

Disconnect the F76 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F76-40 (CANH) - F76-39 (CANL) Ignition switch off 54 to 69 Ω
F76-40 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
F76-39 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
F76-40 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
F76-39 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Parking Assist ECU)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO PARKING ASSIST ECU (CANH, CANL)

57.CONNECT CONNECTOR
a.

Reconnect the E68 No. 5 junction connector.



NEXT

58.CHECK FOR SHORT IN CAN BUS WIRES (DISTANCE CONTROL ECU ASSEMBLY)
58.CHECK FOR SHORT IN CAN BUS WIRES (DISTANCE CONTROL ECU ASSEMBLY)
a.
U164993E01
0.108,0.08 0.361,0.219 0.253,0.139 10 *a 0.564,1.475 0.977,1.613 0.413,0.139 10 CANL 1.005,2.093 1.418,2.232 0.413,0.139 10 CG 2.18,1.467 2.593,1.605 0.413,0.139 10 CANH 0.108,1.997 0.361,2.236 0.253,0.239 10 *b 1.065,1.55 1.247,1.55 1.247,1.55 1.517,0.99 false 1.595,0.99 1.974,1.544 1.974,1.544 2.161,1.544 false 0.396,0.897 0.739,1.035 0.343,0.139 10 E108 0.441,2.661 0.708,2.800 0.267,0.139 10 E22 1.293,2.173 1.446,2.173 1.446,2.173 1.665,2.525 false 2.233,2.978 2.387,3.184 2.387,3.184 2.507,3.184 false 2.523,3.111 2.936,3.250 0.413,0.139 10 BAT

Disconnect the E108 distance control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E108-8 (CANH) - E108-9 (CANL) Ignition switch off 54 to 69 Ω
E108-8 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E108-9 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E108-8 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E108-9 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Distance Control ECU Assembly)
*b Front view of DLC3



OK

REPLACE DISTANCE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DISTANCE CONTROL ECU ASSEMBLY (CANH, CANL)

59.CONNECT CONNECTOR
a.

Reconnect the E68 No. 5 junction connector.



NEXT

60.CHECK FOR SHORT IN CAN BUS WIRES (SEAT BELT CONTROL ECU)
60.CHECK FOR SHORT IN CAN BUS WIRES (SEAT BELT CONTROL ECU)
a.
U165303E02
2.177,2.885 2.354,3.146 2.354,3.146 2.5,3.146 false 1.583,2.406 1.354,2.073 1.354,2.073 1.208,2.073 false 1.479,1.146 1.271,1 1.271,1 1.156,1 false 1.646,1.063 1.219,0.604 1.219,0.604 1.104,0.604 false 0.063,1.844 0.323,2.052 0.26,0.208 10 false *b 0.063,0.052 0.313,0.26 0.25,0.208 10 false *a 0.385,2.563 0.76,2.771 0.375,0.208 10 false E22 0.906,1.99 1.26,2.208 0.354,0.219 10 false CG 2.563,3.063 2.948,3.281 0.385,0.219 10 false BAT 2.448,1.146 2.833,1.354 0.385,0.208 10 false E42 0.656,0.917 1.135,1.135 0.479,0.219 10 false CANH 0.625,0.521 1.104,0.729 0.479,0.208 10 false CANL

Disconnect the E42 seat belt control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E42-1 (CANH) - E42-2 (CANL) Ignition switch off 54 to 69 Ω
E42-1 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E42-2 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E42-1 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E42-2 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Seat Belt Control ECU)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SEAT BELT CONTROL ECU (CANH, CANL)

61.CONNECT CONNECTOR
a.

Reconnect the E68 No. 5 junction connector.



NEXT

62.CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR ASSEMBLY)
62.CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR ASSEMBLY)
a.
U165304E02
2.177,2.885 2.354,3.146 2.354,3.146 2.5,3.146 false 1.583,2.406 1.354,2.073 1.354,2.073 1.208,2.073 false 1.604,1.083 1.917,1.594 1.917,1.594 2.031,1.594 false 1.448,1.083 1.135,1.594 1.135,1.594 1.021,1.594 false 0.063,1.844 0.323,2.063 0.26,0.219 10 false *b 0.063,0.052 0.344,0.292 0.281,0.24 10 false *a 0.396,2.563 0.74,2.76 0.344,0.198 10 false E22 0.885,1.99 1.219,2.198 0.333,0.208 10 false CG 2.552,3.052 3.042,3.292 0.49,0.24 10 false BAT 0.406,0.969 0.76,1.167 0.354,0.198 10 false E50 0.521,1.51 0.979,1.75 0.458,0.24 10 false CANL 2.073,1.51 2.615,1.75 0.542,0.24 10 false CANH

Disconnect the E50 yaw rate sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E50-3 (CANH) - E50-2 (CANL) Ignition switch off 54 to 69 Ω
E50-3 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E50-2 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E50-3 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E50-2 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR ASSEMBLY (CANH, CANL)

63.CONNECT CONNECTOR
a.

Reconnect the E71 No. 4 junction connector.



NEXT

64.CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY)
64.CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY)
a.
U165161E01
0.085,1.885 0.268,2.045 0.183,0.160 10 *b 2.546,3.067 2.844,3.212 0.298,0.145 10 BAT 0.883,2.065 1.131,2.204 0.247,0.140 10 CG 2.739,1.13 3.082,1.266 0.343,0.136 10 E102 0.393,2.693 0.657,2.829 0.264,0.136 10 E22 0.085,0.073 0.255,0.233 0.170,0.161 10 *a 1.877,1.557 2.274,1.696 0.397,0.139 10 CANL 0.121,1.557 0.541,1.696 0.420,0.139 10 CANH 1.36,1.329 1.625,1.642 1.625,1.642 1.86,1.642 false 1.23,1.329 0.875,1.661 0.875,1.661 0.634,1.661 false 2.216,2.962 2.349,3.142 2.349,3.142 2.51,3.142 false 1.665,2.526 1.399,2.135 1.399,2.135 1.164,2.135 false

Disconnect the E102 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E102-1 (CANH) - E102-2 (CANL) Ignition switch off 54 to 69 Ω
E102-1 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E102-2 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E102-1 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E102-2 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)

65.CONNECT CONNECTOR
a.

Reconnect the E71 No. 4 junction connector.



NEXT

66.CHECK FOR SHORT IN CAN BUS WIRES (4WD CONTROL ECU)
66.CHECK FOR SHORT IN CAN BUS WIRES (4WD CONTROL ECU)
a.
U165292E02
2.177,2.885 2.354,3.146 2.354,3.146 2.5,3.146 false 1.583,2.406 1.354,2.073 1.354,2.073 1.208,2.073 false 2.729,1.135 2.344,1.594 2.344,1.594 2.229,1.594 false 2.844,1.135 2.677,1.792 2.677,1.792 2.563,1.792 false 0.063,1.844 0.344,2.073 0.281,0.229 10 false *b 0.063,0.052 0.344,0.25 0.281,0.198 10 false *a 0.396,2.563 0.771,2.771 0.375,0.208 10 false E22 0.906,1.99 1.188,2.135 0.281,0.146 10 false CG 2.563,3.063 2.99,3.271 0.427,0.208 10 false BAT 1.563,0.354 1.958,0.563 0.396,0.208 10 false A27 2.073,1.708 2.531,1.906 0.458,0.198 10 false CAN- 1.719,1.51 2.208,1.698 0.49,0.188 10 false CAN+

Disconnect the A27 4WD control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A27-19 (CAN+) - A27-20 (CAN-) Ignition switch off 54 to 69 Ω
A27-19 (CAN+) - E22-4 (CG) Ignition switch off 200 Ω or higher
A27-20 (CAN-) - E22-4 (CG) Ignition switch off 200 Ω or higher
A27-19 (CAN+) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
A27-20 (CAN-) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to 4WD Control ECU)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CAN+, CAN-)

67.CONNECT CONNECTOR
a.

Reconnect the E71 No. 4 junction connector.



NEXT

68.CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU)
68.CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU)
a.
U165214E01
0.06,1.846 0.243,2.006 0.183,0.160 10 *b 2.625,3.029 2.923,3.174 0.298,0.145 10 BAT 0.898,1.956 1.146,2.096 0.247,0.140 10 CG 2.653,1.002 2.917,1.138 0.264,0.136 10 E31 0.476,2.591 0.740,2.727 0.264,0.136 10 E22 0.06,0.067 0.230,0.228 0.170,0.161 10 *a 0.815,1.607 1.212,1.745 0.397,0.139 10 CA2L 0.496,1.393 0.916,1.532 0.420,0.139 10 CA2H 1.521,1.158 1.256,1.471 1.256,1.471 1.021,1.471 false 2.253,2.876 2.435,3.105 2.435,3.105 2.588,3.105 false 1.68,2.418 1.414,2.027 1.414,2.027 1.179,2.027 false 1.63,1.158 1.545,1.677 1.545,1.677 1.31,1.677 false

Disconnect the E31 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E31-13 (CA2H) - E31-12 (CA2L) Ignition switch off 108 to 132 Ω
E31-13 (CA2H) - E22-4 (CG) Ignition switch off 200 Ω or higher
E31-12 (CA2L) - E22-4 (CG) Ignition switch off 200 Ω or higher
E31-13 (CA2H) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E31-12 (CA2L) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO NETWORK GATEWAY ECU (CA2H, CA2L)

69.CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND)
a.
U165157E01
0.455,1.136 0.728,1.273 0.273,0.137 10 E31 2.273,1.122 2.561,0.778 2.561,0.778 2.684,0.778 false 1.351,1.122 1.005,0.73 1.005,0.73 0.882,0.73 false 2.708,0.696 3.084,0.833 0.376,0.137 10 BATT 0.449,0.649 0.825,0.786 0.376,0.137 10 GND 0.07,0.056 0.371,0.193 0.301,0.137 10 *a 2.039,1.293 2.463,1.64 2.463,1.64 2.601,1.64 false 2.242,1.98 2.122,1.98 2.122,1.98 1.931,1.292 false 0.07,0.056 0.371,0.193 0.301,0.137 10 *a 2.613,1.56 2.900,1.698 0.287,0.137 10 IG2 2.266,1.895 2.804,2.032 0.538,0.137 10 IG1

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the E31 network gateway ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E31-4 (GND) - Body ground Ignition switch off Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E31-2 (BATT) - Body ground Always 11 to 14 V
E31-9 (IG2) - Body ground Ignition switch ON 11 to 14 V
E31-10 (IG1) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR