Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System) › from 2015.08
RM2660E _58 Vehicle Interior _052845 SEAT _0255625 FRONT POWER SEAT CONTROL SYSTEM(w/ Seat Position Memory System) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Seat Position Memory System)  Wireless-linked Return Function does not Operate  


DESCRIPTION

When a door is unlocked using the wireless unlock function or smart key unlock function, the certification ECU (smart key ECU assembly) sends a door unlock signal and key ID signal to the main body ECU (multiplex network body ECU). When the main body ECU (multiplex network body ECU) receives the door unlock signal, it stores the key ID. When the driver door is opened, the memory call and memory command information of the stored key ID is sent to front power seat switch. Front power seat switch receives the memory commands and performs the memory call operation according to predetermined control timing values.

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU) or the certification ECU (smart key ECU assembly), refer to the Entry and Start System (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the GTS to check if the CAN communication system is functioning normally.


OK:

CAN communication DTC is not output.


Result
Result Proceed to
OK A
NG (for LHD (w/ Central Gateway ECU)) B
NG (for LHD (w/o Central Gateway ECU)) C
NG (for RHD (w/ Central Gateway ECU)) D
NG (for RHD (w/o Central Gateway ECU)) E



A

2.CHECK FRONT POWER SEAT CONTROL SYSTEM

B

C

D

E

2.CHECK FRONT POWER SEAT CONTROL SYSTEM



d.

Check the memory call registration function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).

Result
Result Proceed to
OK A
NG (power seat control function) B
NG (seat position memory function) C
NG (seat position restoring function) D
NG (memory call registration function) E



A

3.CHECK MEMORY CALL FUNCTION (WIRELESS UNLOCK OR ENTRY UNLOCK)

B

C

D

E

3.CHECK MEMORY CALL FUNCTION (WIRELESS UNLOCK OR ENTRY UNLOCK)
a.

Turn the engine switch off.


b.

Close and lock all doors.


c.

Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.


d.

Open the driver door and check that the driver seat moves to the memorized position.

Result
Result Proceed to
Memory call function linked with the wireless unlock function does not operate. A
Memory call function linked with the entry unlock function does not operate. B
Both memory call function linked with the wireless unlock function and entry unlock function do not operate. C



A

4.CHECK WIRELESS UNLOCK FUNCTION

B

10.CHECK ENTRY AND START SYSTEM (for Entry Function)

C

16.CHECK MEMORY CALL FUNCTION (MIRROR OPERATION)
4.CHECK WIRELESS UNLOCK FUNCTION
a.

Check the wireless unlock function (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>OPERATION CHECK).

OK:

Wireless unlock function is normal.




OK

5.CHECK MEMORY CALL FUNCTION (MIRROR OPERATION)

NG

5.CHECK MEMORY CALL FUNCTION (MIRROR OPERATION)
a.

Perform the memory call function and check the outer mirror operation (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).

OK:

Outer mirror operates normally.




OK

6.REPLACE FRONT POWER SEAT SWITCH

NG

8.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
6.REPLACE FRONT POWER SEAT SWITCH
a.

Temporarily replace the front power seat switch LH*1, RH*2 with a new or normally functioning one (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY).

*1: for LHD

*2: for RHD



NEXT

7.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
7.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).

OK:

Memory call function linked with the wireless unlock function operates normally.




OK

END (FRONT POWER SEAT SWITCH WAS DEFECTIVE)

NG

8.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
8.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Temporarily replace the main body ECU (multiplex network body ECU) with a new one.




NEXT

9.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
9.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).

OK:

Memory call function linked with the wireless unlock function operates normally.




OK

END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.CHECK ENTRY AND START SYSTEM (for Entry Function)
a.

Check the entry unlock function of the entry and start system (for entry function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).

OK:

Entry unlock function is normal.




OK

11.CHECK MEMORY CALL FUNCTION (MIRROR OPERATION)

NG

11.CHECK MEMORY CALL FUNCTION (MIRROR OPERATION)
a.

Perform the memory call function and check the outer mirror operation (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).

OK:

Outer mirror operates normally.


Result
Result Proceed to
OK A
NG B



A

12.REPLACE FRONT POWER SEAT SWITCH

B

14.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
12.REPLACE FRONT POWER SEAT SWITCH
a.

Temporarily replace the front power seat switch LH*1, RH*2 with a new or normally functioning one (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY).

*1: for LHD

*2: for RHD



NEXT

13.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
13.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).

OK:

Memory call function linked with the wireless unlock function operates normally.

Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD C




A

END (FRONT POWER SEAT SWITCH WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

14.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Temporarily replace the main body ECU (multiplex network body ECU) with a new one.




NEXT

15.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
15.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).

OK:

Memory call function linked with the wireless unlock function operates normally.




OK

END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

16.CHECK MEMORY CALL FUNCTION (MIRROR OPERATION)
a.

Perform the memory call function and check the outer mirror operation (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).

OK:

Outer mirror operates normally.




OK

17.REPLACE FRONT POWER SEAT SWITCH

NG

19.READ VALUE USING GTS (MEM SW NO. w/ KEY ID)
17.REPLACE FRONT POWER SEAT SWITCH
a.

Temporarily replace the front power seat switch LH*1, RH*2 with a new or normally functioning one (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY).

*1: for LHD

*2: for RHD



NEXT

18.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
18.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).

OK:

Memory call function linked with the wireless unlock function operates normally.

Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

END (FRONT POWER SEAT SWITCH WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

19.READ VALUE USING GTS (MEM SW NO. w/ KEY ID)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Mem SW No. w/KeyID1 Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID1
MEM SW1: M1 switch linked with key ID1
MEM SW2: M2 switch linked with key ID1
MEM SW3: M3 switch linked with key ID1
-
Mem SW No. w/KeyID2 Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID2
MEM SW1: M1 switch linked with key ID2
MEM SW2: M2 switch linked with key ID2
MEM SW3: M3 switch linked with key ID2
-
Mem SW No. w/KeyID3 Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID3
MEM SW1: M1 switch linked with key ID3
MEM SW2: M2 switch linked with key ID3
MEM SW3: M3 switch linked with key ID3
-
Mem SW No. w/KeyID4 Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID4
MEM SW1: M1 switch linked with key ID4
MEM SW2: M2 switch linked with key ID4
MEM SW3: M3 switch linked with key ID4
-
Mem SW No. w/KeyID5 Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID5
MEM SW1: M1 switch linked with key ID5
MEM SW2: M2 switch linked with key ID5
MEM SW3: M3 switch linked with key ID5
-
Mem SW No. w/KeyID6 Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID6
MEM SW1: M1 switch linked with key ID6
MEM SW2: M2 switch linked with key ID6
MEM SW3: M3 switch linked with key ID6
-
Mem SW No. w/KeyID7 Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID7
MEM SW1: M1 switch linked with key ID7
MEM SW2: M2 switch linked with key ID7
MEM SW3: M3 switch linked with key ID7
-


f.

Enter the following menus: Body Electrical / Driver Seat / Data List.


g.

Read the Data List according to the display on the GTS.

Driver Seat
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Seat Memory No1 Seat position memorized with M1 switch / Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Seat Memory No2 Seat position memorized with M2 switch / Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Seat Memory No3 Seat position memorized with M3 switch / Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-

OK:

On the GTS display, it is confirmed that the memory switches which are linked with key IDs memorize the seat position (for example, on the GTS display, "Mem SW No. w/KeyID1" displays "MEM SW1" and "Seat Memory No1" displays "Mem").




OK

20.READ VALUE USING GTS (DOOR COURTESY SW)

NG

20.READ VALUE USING GTS (DOOR COURTESY SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FL Door Courtesy SW Front door courtesy light switch assembly LH signal / ON or OFF ON: Driver door open
OFF: Driver door closed
for LHD
FR Door Courtesy SW Front door courtesy light switch assembly RH signal / ON or OFF ON: Driver door open
OFF: Driver door closed
for RHD

OK:

On the GTS screen, each item changes between ON and OFF according to the above.




OK

21.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

21.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Temporarily replace the main body ECU (multiplex network body ECU) with a new one.




NEXT

22.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
22.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).

OK:

Memory call function linked with the wireless unlock function operates normally.




OK

END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)