Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System) › from 2015.08
RM2660E _58 Vehicle Interior _052845 SEAT _0255625 FRONT POWER SEAT CONTROL SYSTEM(w/ Seat Position Memory System) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Seat Position Memory System)  Wireless Transmitter Memory Function does not Operate  


DESCRIPTION

With the engine switch off and the driver door closed, press the transmitter lock or unlock switch while holding a seat memory switch (seat memory switch 1, seat memory switch 2 or seat memory switch 3). Doing so will register the transmitter recognition code into the seat memory switch that was pressed. After the registration is complete, the answer-back buzzer sounds.

CAUTION / NOTICE / HINT

NOTICE:
·

The front power seat control system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

The seat position will not be stored if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously. If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

·

The seat will not return to the memorized position if 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously. If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.

·

Before replacing the main body ECU (multiplex network body ECU) or the certification ECU (smart key ECU assembly), refer to the Entry and Start System (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

Check the manual lock/unlock function by using the door control switch (multiplex network master switch assembly) (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Manual lock/unlock function operates normally.




OK

2.CHECK ENTRY AND START SYSTEM (for Start Function)

NG

2.CHECK ENTRY AND START SYSTEM (for Start Function)
a.

Check that the engine starts normally when the engine switch is pressed while carrying the electrical key transmitter sub-assembly and with the brake pedal depressed (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>OPERATION CHECK).

OK:

Engine starts normally.




OK

3.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION

NG

3.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check the seat position memory and restoring functions (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK)

Result:
Result Proceed to
OK A
NG (seat position memory function does not operate normally) B
NG (seat position restoring function does not operate normally) C




A

4.READ VALUE USING GTS (DOOR COURTESY SW)

B

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

C

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat does not Return to Memorized Position)

4.READ VALUE USING GTS (DOOR COURTESY SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FL Door Courtesy SW Front door courtesy light switch assembly LH signal / ON or OFF ON: Driver door open
OFF: Driver door closed
for LHD
FR Door Courtesy SW Front door courtesy light switch assembly RH signal / ON or OFF ON: Driver door open
OFF: Driver door closed
for RHD


OK:

On the GTS screen, On or OFF is displayed accordingly.



OK

5.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)

NG

5.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
a.

Check the memory registration of the memory call function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK)

OK:

Memory registration operates normally.




OK

6.READ VALUE USING GTS (Mem SW No. w/KeyID)

NG

8.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
6.READ VALUE USING GTS (Mem SW No. w/KeyID)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Mem SW No. w/KeyID1 Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID1
MEM SW1: M1 switch linked with key ID1
MEM SW2: M2 switch linked with key ID1
MEM SW3: M3 switch linked with key ID1
-
Mem SW No. w/KeyID2 Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID2
MEM SW1: M1 switch linked with key ID2
MEM SW2: M2 switch linked with key ID2
MEM SW3: M3 switch linked with key ID2
-
Mem SW No. w/KeyID3 Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID3
MEM SW1: M1 switch linked with key ID3
MEM SW2: M2 switch linked with key ID3
MEM SW3: M3 switch linked with key ID3
-
Mem SW No. w/KeyID4 Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID4
MEM SW1: M1 switch linked with key ID4
MEM SW2: M2 switch linked with key ID4
MEM SW3: M3 switch linked with key ID4
-
Mem SW No. w/KeyID5 Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID5
MEM SW1: M1 switch linked with key ID5
MEM SW2: M2 switch linked with key ID5
MEM SW3: M3 switch linked with key ID5
-
Mem SW No. w/KeyID6 Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID6
MEM SW1: M1 switch linked with key ID6
MEM SW2: M2 switch linked with key ID6
MEM SW3: M3 switch linked with key ID6
-
Mem SW No. w/KeyID7 Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID7
MEM SW1: M1 switch linked with key ID7
MEM SW2: M2 switch linked with key ID7
MEM SW3: M3 switch linked with key ID7
-


OK:

A seat position memory switch is linked to the electrical key transmitter sub-assembly.

Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

7.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).

OK:

Memory registration and automatic memory call function operates normally.




OK

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Wireless-linked Return Function does not Operate)

8.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU) with a new or known good one.




NEXT

9.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
9.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
a.

Check the memory registration of the memory call function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK)

OK:

Memory registration operates normally.




OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

10.REPLACE FRONT POWER SEAT SWITCH
10.REPLACE FRONT POWER SEAT SWITCH
a.

Replace the front power seat switch LH*1, RH*2 with a new or known good one (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY).

*1: for LHD

*2: for RHD



NEXT

11.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
11.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
a.

Check the memory registration of the memory call function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).

OK:

Memory registration operates normally.




OK

END (FRONT POWER SEAT SWITCH WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)