Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD DEICER SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255726 WINDSHIELD DEICER SYSTEM J

WINDOW / GLASS  WINDSHIELD DEICER SYSTEM  Windshield Deicer does not Operate  


DESCRIPTION

When the windshield deicer switch is turned on, a windshield deicer activation request signal is sent via the LIN communication line*1 or CAN communication line and UART communication line*2 to the air conditioning amplifier assembly. Then the air conditioning amplifier assembly operates the windshield deicer. When the on signal from the windshield deicer switch is received, the DEICER relay is operated for 15 minutes. Also, if the off signal from the switch is received within 15 minutes, the DEICER relay operation is stopped.

*1: w/o Navigation System

*2: w/ Navigation System


WIRING DIAGRAM

E275375E02
0.188,0.635 1.625,0.854 1.438,0.219 10 false from IG1 NO.1 Relay 0.677,1.052 1.448,1.229 0.771,0.177 10 false from Battery 2,1.25 2.542,1.427 0.542,0.177 10 false DEICER 2.094,0.802 2.563,1.01 0.469,0.208 10 false LH-IG 3.688,1.427 4.229,1.604 0.542,0.177 10 false DEICER 1.094,2.448 2.094,2.615 1,0.167 10 false A23*7, A63*6 5.115,0.635 5.375,0.781 0.26,0.146 10 false E36 5.479,0.635 5.76,0.823 0.281,0.188 10 false E81 5.177,0.854 5.333,1.031 0.156,0.177 10 false *3 5.552,0.854 5.708,1.031 0.156,0.177 10 false *4 1.094,2.646 2.823,3.063 1.729,0.417 10 false Windshield Glass (Windshield Deicer Wire) 5.156,0.438 5.365,0.646 0.208,0.208 10 false 23 3.198,0.51 3.354,0.688 0.156,0.177 10 false 2 3.198,1.167 3.354,1.344 0.156,0.177 10 false 5 4.604,0.51 4.76,0.688 0.156,0.177 10 false 1 1.073,1.927 1.229,2.104 0.156,0.177 10 false 2 1.271,1.927 1.427,2.104 0.156,0.177 10 false E 2.479,1.927 2.635,2.104 0.156,0.177 10 false 1 2.25,1.927 2.406,2.104 0.156,0.177 10 false B 4.604,1.156 4.76,1.333 0.156,0.177 10 false 3 5.531,0.427 5.698,0.604 0.167,0.177 10 false 40 5.854,0.635 6.271,0.813 0.417,0.177 10 false FDEF 3.448,5.844 4.958,6.323 1.51,0.479 10 false Air Conditioning Control Assembly*1 2.208,4.292 3,4.635 0.792,0.344 10 false Multi-display Assembly*2 3.625,4.281 4.979,4.625 1.354,0.344 10 false Multi-media Module Receiver Assembly*2 5.417,5.792 6.99,6.135 1.573,0.344 10 false Air Conditioning Amplifier Assembly 1.115,6.021 2.729,6.198 1.615,0.177 10 false : LIN Communication Line 1.115,6.427 2.802,6.604 1.688,0.177 10 false : CAN Communication Line 0.323,5.146 3.125,5.354 2.802,0.208 10 false *6: w/ Heated Windshield Defroster System 0.313,3.406 1.958,3.583 1.646,0.177 10 false *1: w/o Navigation System 0.313,3.771 1.896,3.948 1.583,0.177 10 false *2: w/ Navigation System 0.313,4.135 1.552,4.313 1.24,0.177 10 false *3: w/ Rear Heater 0.313,4.5 1.604,4.677 1.292,0.177 10 false *4: w/o Rear Heater 3.063,2.583 4.438,3.042 1.375,0.458 10 false to Heated Windshield Defroster System*5 5.021,2.25 5.208,2.427 0.188,0.177 10 false *6 3.375,3.927 3.563,4.104 0.188,0.177 10 false *5 0.313,4.833 2.25,5.031 1.938,0.198 10 false *5: UART Communication Line 0.323,5.469 3.125,5.677 2.802,0.208 10 false *7: w/o Heated Windshield Defroster System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC

*1: w/o Navigation System

*2: w/ Navigation System


a.

Check if the LIN communication system*1 or CAN communication system*2 is functioning normally.


Result
Result Proceed to
DTC is not output A
LIN DTC is output*1 B
CAN DTC is output (for LHD)*2 C
CAN DTC is output (for RHD)*2 D



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DEICER RELAY [FRONT])

B

C

D

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DEICER RELAY [FRONT])
a.

Select the Active Test using the intelligent tester to generate a control command, and then check that the windshield deicer operates (See page Vehicle Exterior>WINDOW / GLASS>WINDSHIELD DEICER SYSTEM>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Deicer Relay (Front) DEICER relay operation OFF or ON -

OK:

The windshield deicer system operates normally.


Result
Result Proceed to
OK (w/o Navigation System) A
OK (w/ Navigation System) B
NG C



A

3.CHECK AIR CONDITIONING CONTROL ASSEMBLY

B

4.CHECK NAVIGATION SYSTEM

C

7.INSPECT DEICER RELAY
3.CHECK AIR CONDITIONING CONTROL ASSEMBLY
a.

Temporarily replace the air conditioning control assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL(w/o Multi-display)>REMOVAL).


b.

Turn the ignition switch to ON.


c.

Check that pressing the windshield deicer switch illuminates the indicator and warms the front windshield surface.


d.

Check that after approximately 15 minutes, the indicator light turns off and the windshield deicer deactivates.

OK:

Windshield deicer system functioning normally.




OK

END (AIR CONDITIONING CONTROL ASSEMBLY IS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

4.CHECK NAVIGATION SYSTEM
a.

Check if the navigation system functioning normally (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

OK:

Navigation system functioning normally.




OK

5.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

5.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Temporarily replace the air conditioning amplifier assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


b.

Turn the ignition switch to ON.


c.

Check that pressing the windshield deicer switch illuminates the indicator and warms the front windshield surface.


d.

Check that after approximately 15 minutes, the indicator light turns off and the windshield deicer deactivates.

OK:

Windshield deicer system functioning normally.




OK

END (AIR CONDITIONING AMPLIFIER ASSEMBLY IS DEFECTIVE)

NG

6.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY
6.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.

Temporarily replace the multi-media module receiver assembly with a new or normally functioning one (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/ Multi-display)>REMOVAL).


b.

Turn the ignition switch to ON.


c.

Check that pressing the windshield deicer switch illuminates the indicator and warms the front windshield surface.


d.

Check that after approximately 15 minutes, the indicator light turns off and the windshield deicer deactivates.

OK:

Windshield deicer system functioning normally.




OK

END (MULTI-MEDIA MODULE RECEIVER ASSEMBLY IS DEFECTIVE)

NG

7.INSPECT DEICER RELAY
a.

Remove the DEICER relay from the engine room relay block (See page Vehicle Exterior>WINDOW / GLASS>RELAY(for Windshield Deicer)>ON-VEHICLE INSPECTION).




OK

8.CHECK HARNESS AND CONNECTOR (DEICER RELAY - AIR CONDITIONING AMPLIFIER AND BATTERY)

NG

8.CHECK HARNESS AND CONNECTOR (DEICER RELAY - AIR CONDITIONING AMPLIFIER AND BATTERY)
a.

Remove the DEICER relay from the engine room relay block (See page Vehicle Exterior>WINDOW / GLASS>RELAY(for Windshield Deicer)>ON-VEHICLE INSPECTION).


b.

Disconnect the E36*1 or E81*2 air conditioning amplifier assembly connector.

*1: w/ Rear Heater

*2: w/o Rear Heater



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DEICER relay terminal 2 - Body ground Ignition switch ON 11 to 14 V
DEICER relay terminal 5 - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Rear Heater:
Tester Connection Condition Specified Condition
DEICER relay terminal 1 - E36-23 (FDEF) Always Below 1 Ω
DEICER relay terminal 1 - Body ground Always 10 kΩ or higher

w/o Rear Heater:
Tester Connection Condition Specified Condition
DEICER relay terminal 1 - E81-40 (FDEF) Always Below 1 Ω
DEICER relay terminal 1 - Body ground Always 10 kΩ or higher




OK

9.CHECK HARNESS AND CONNECTOR (WINDSHIELD GLASS [WINDSHIELD DEICER WIRE] - DEICER RELAY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (WINDSHIELD GLASS [WINDSHIELD DEICER WIRE] - DEICER RELAY AND BODY GROUND)

*1: w/o Heated Windshield Defroster System

*2: w/ Heated Windshield Defroster System


a.

Disconnect the A23*1 or A63*2 windshield glass (windshield deicer wire) connector.


b.

Remove the DEICER relay from the engine room relay block (See page Vehicle Exterior>WINDOW / GLASS>RELAY(for Windshield Deicer)>ON-VEHICLE INSPECTION).


c.

Remove the HWD1, HWD2, HWD3 and HWD4 relays from the No. 2 engine room relay block (See page Vehicle Exterior>WINDOW / GLASS>RELAY(for Window Defogger)>ON-VEHICLE INSPECTION).*2


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Heated Windshield Defroster System:
Tester Connection Condition Specified Condition
A23-1 (B) - DEICER relay terminal 3 Always Below 1 Ω
A23-2 (E) - Body ground Always Below 1 Ω
DEICER relay terminal 3 - Body ground Always 10 kΩ or higher

w/ Heated Windshield Defroster System:
Tester Connection Condition Specified Condition
A63-1 (B) - DEICER relay terminal 3 Always Below 1 Ω
A63-2 (E) - Body ground Always Below 1 Ω
DEICER relay terminal 3 - Body ground Always 10 kΩ or higher




OK

10.CHECK WINDSHIELD GLASS (WINDSHIELD DEICER WIRE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK WINDSHIELD GLASS (WINDSHIELD DEICER WIRE)
a.
U166442E02
1.844,2.469 2.24,2.844 false 1.479,2.479 1.083,2.854 false 1.854,0.74 2.24,1.115 false 1.542,0.75 1.146,1.125 false 0.083,0.052 0.344,0.25 0.26,0.198 10 false *a 0.958,2.833 1.156,3.01 0.198,0.177 10 false E 0.719,2.365 1.052,2.552 0.333,0.188 10 false A63 2.313,2.802 2.531,3.031 0.219,0.229 10 false B 0.594,1.573 0.854,1.771 0.26,0.198 10 false *B 1,1.083 1.198,1.26 0.198,0.177 10 false E 0.781,0.635 1.115,0.823 0.333,0.188 10 false A23 2.333,1.042 2.615,1.229 0.281,0.188 10 false B 0.573,0.094 0.844,0.292 0.271,0.198 10 false *A

Disconnect the A23*1 or A63*2 windshield glass (windshield deicer wire) connector.

*1: w/o Heated Windshield Defroster System

*2: w/ Heated Windshield Defroster System



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o Heated Windshield Defroster System:
Tester Connection Switch Condition Specified Condition
A23-1 (B) - A23-2 (E) Ignition switch ON and deicer switch on 11 to 14 V

w/ Heated Windshield Defroster System:
Tester Connection Switch Condition Specified Condition
A63-1 (B) - A63-2 (E) Ignition switch ON and deicer switch on 11 to 14 V


Text in Illustration
*A w/o Heated Windshield Defroster System
*B w/ Heated Windshield Defroster System
*a Front view of wire harness connector:
(to Window Glass [Windshield Deicer Wire])



OK

REPLACE WINDSHIELD GLASS (WINDSHIELD DEICER WIRE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY