Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/ Secondary Air Injection System) › from 2017.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0327320 SFI SYSTEM(w/ Secondary Air Injection System) C

3UR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P2444  Secondary Air Injection System Pump Stuck On Bank1  P2445  Secondary Air Injection System Pump Stuck Off Bank1  P2446  Secondary Air Injection System Pump Stuck On Bank 2  P2447  Secondary Air Injection System Pump Stuck Off Bank 2  


DESCRIPTION

Refer to P2440 (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>SFI SYSTEM(w/ Secondary Air Injection System)>P2440).

DTC No. DTC Detection Condition Trouble Area
P2444
P2446
The secondary air pressure is 2.4 kPa (18 mmHg) or more despite the ECM commanding the air pump to turn off (2 trip detection logic).
·

Short in air pump circuit

·

Open or short in pressure sensor circuit

·

Pressure sensor

·

Air Injection Control Driver (AID)

·

ECM


P2445
P2447
The secondary air pressure is less than 2.4 kPa (18 mmHg) despite the ECM commanding the air pump to turn on (2 trip detection logic).
·

Air pump

·

Open in air pump circuit

·

Air injection system piping

·

Vacuum hose (pressure sensor - air switching valve)

·

Pressure sensor

·

Open or short in pressure sensor circuit

·

Air Injection Control Driver (AID)

·

ECM



MONITOR DESCRIPTION

The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the Air Switching Valve (ASV) of the Secondary Air Injection (AIR) system. The sensor measures the pressure in the secondary air passage and transmits a signal to the ECM.

If either of the following conditions occurs, the ECM interprets it as a malfunction of the AIR system, illuminates the MIL and stores DTC(s):

·

The pressure indicated by the pressure sensor does not reach threshold levels despite the ECM turning on the air pump.

·

The pressure indicated by the pressure sensor exceeds threshold levels despite the ECM turning off the air pump.


CAUTION / NOTICE / HINT

HINT:

Determination by ECM monitoring:

The ECM locates malfunctions in the Secondary Air Injection (AIR) system by detecting the pressure in the AIR passage between the air pump and Air Switching Valve (ASV) and stores DTC(s). Soon after a cold engine start, the monitor runs for a short time while the AIR system is both ON and OFF. The ECM detects both the pressure and the exhaust pulsation and compares them.

The following 8 patterns are AIR system pressure conditions in the AIR system passage.


Pressure Condition in Secondary Air Injection System Case 1:
Air Pump ON
Air Switching Valve Open
Pressure 2.4 kPa or higher
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 2:
Air Pump OFF
Air Switching Valve Open
Pressure Below 2.4 kPa
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 3:
Air Pump ON
Air Switching Valve Closed
Pressure 2.4 kPa or higher
Pulsation Detection Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 4:
Air Pump OFF
Air Switching Valve Close
Pressure Below 2.4 kPa
Pulsation Detection Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 5:
Air Pump ON
Air Switching Valve Open
Pressure 2.4 kPa or higher
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 6:
Air Pump OFF
Air Switching Valve Open
Pressure Below 2.4 kPa
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 7:
Air Pump ON
Air Switching Valve Closed
Pressure 2.4 kPa or higher
Pulsation Detection Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 8:
Air Pump OFF
Air Switching Valve Close
Pressure Below 2.4 kPa
Pulsation Detection Exhaust gas pulsation not detected

If the detected pressure is high, the air pump is assumed to be ON and if it alternates sharply, the ASV is assumed to be open. The ECM locates malfunctions from the combination of pressures detected when the AIR system is ON and OFF.

HINT:

The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.


HINT:
·

In case 3 and 7, as the pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the ASV, the average pressure is higher than in case 1 (approximately 20 to 30 kPa).

·

In case 1, the average pressure is approximately 3 to 11 kPa. The value of 2.4 kPa indicated in the table above is a threshold for detecting pump malfunctions.



Detected Conditions while AIR Operating:
Air Pump ON, ASV Open
Detected Conditions while AIR not Operating:
Air Pump OFF, ASV Closed
ECM Determination DTCs Output
Case 1 Case 8 Normal -
Case 1 Case 6 ASV stuck open P2440
or
P2442
Case 1 Case 7 Air pump stuck ON P2444
or
P2446
Case 2 Case 8 Air pump stuck OFF P2445
or
P2447
Case 3 Case 8 ASV stuck closed P2441
or
P2443
Case 1 Case 5 ASV stuck open and air pump stuck ON P2440 and P2444
or
P2442 and P2446
Case 2 Case 6 ASV stuck open and air pump stuck OFF P2440 and P2445
or
P2442 and P2447
Case 3 Case 7 ASV stuck closed and air pump stuck ON P2441 and P2444
or
P2443 and P2446
Case 4 Case 8 ASV stuck closed and air pump stuck OFF P2441 and P2445
or
P2443 and P2447

HINT:
·

If the vacuum hose between the ASV and the pressure sensor is not connected correctly, case 4 may occur.

·

By using the GTS to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, Pending Codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



System Check:

The pressure in the secondary air passage can be checked using the GTS.

(a)

Start the engine and warm it up.

(b)

Turn the engine switch off.

(c)

Connect the GTS to the DLC3.

(d)

Turn the engine switch on (IG) and turn the GTS on.

(e)

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1 CLOSE, AIR PUMP 2: OFF, ASV2 CLOSE.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.


(f)

Start the engine.

(g)

Perform the AIR system intrusive operation while the engine is idling.

(h)

Check that the status of the air pump (AIR PUMP), ASV and pressure in the AIR system passage (PRESSURE) displayed on the GTS indicate the conditions shown in the table below.

Standard:
Operations AIR PUMP ASV PRESSURE*1 PULSATION*2
AIR PUMP: ON, ASV: OPEN ON OPEN 2.4 kPa or higher 20 kPa or higher
AIR PUMP: OFF, ASV: CLOSE OFF CLOSE Below 2.4 kPa Below 30 kPa


*1:

Average pumping pressure (gauge pressure). The pressure should be 2.4 kPa or higher when the AIR system operates.

*2:

The cumulative exhaust pulsation calculated by the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.

(i)

Turn the engine switch off.

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While AIR system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR).

If an ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.





HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2444, P2445, P2446 AND/OR P2447)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read DTCs.

Result
Result Proceed to
P2444, P2445, P2446 and/or P2447 are output A
P2444, P2445, P2446 and/or P2447 and P0418 and/or P0419 are output B
P2444, P2445, P2446 and/or P2447 and other DTCs (except P0418 and P0419) are output C

If any DTCs other than P0418, P0419, P2444, P2445, P2446 and/or P2447 are output, troubleshoot those DTCs first.



A

2.PERFORM ACTIVE TEST USING GTS (SECONDARY AIR INJECTION SYSTEM OPERATION)

B

C

2.PERFORM ACTIVE TEST USING GTS (SECONDARY AIR INJECTION SYSTEM OPERATION)
a.

Start the engine and warm it up.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



f.

Start the engine.


g.

Perform the AIR system intrusive operation while the engine is idling.


h.

Check that the status of the air pump (AIR PUMP), ASV and pressure in the AIR system passage (PRESSURE) displayed on the GTS indicate the conditions shown in the table below.

Standard:
Operation AIR PUMP ASV PRESSURE*
AIR PUMP: ON, ASV: OPEN ON ON 2.4 kPa or higher
AIR PUMP: OFF, ASV: CLOSE OFF OFF Below 2.4 kPa


*: Average pumping pressure. The pressure should be 2.4 kPa or higher when the AIR system operates.


i.

Turn the engine switch off.

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While AIR system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR).

If an ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.





OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2447)

NG

4.INSPECT VACUUM HOSES (AIR SWITCHING VALVE - PRESSURE SENSOR)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2447)
a.

Start the engine and warm it up.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG) and turn the GTS on.



f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.


g.

Start the engine after the GTS initialization is finished.


h.

Perform the System Check operation by pressing Next.


i.

After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.


j.

Refer to the confirmation driving pattern.


k.

Check pending DTCs.


l.

Turn the engine switch off.

NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.



Result
Result Proceed to
P2444, P2445, P2446 and/or P2447 are output A
No pending DTC is output B



A

4.INSPECT VACUUM HOSES (AIR SWITCHING VALVE - PRESSURE SENSOR)

B

4.INSPECT VACUUM HOSES (AIR SWITCHING VALVE - PRESSURE SENSOR)
a.

Check the vacuum hose connections with the pressure sensor and ASV.


b.

Inspect the vacuum hose for blockages and damage.

OK:

Vacuum hose has no blockages or damage.




OK

5.INSPECT AIR SWITCHING VALVE ASSEMBLY (PRESSURE SENSOR)

NG

REPAIR OR REPLACE VACUUM HOSE

5.INSPECT AIR SWITCHING VALVE ASSEMBLY (PRESSURE SENSOR)

OK

6.CHECK AIR INJECTION SYSTEM PIPE CONNECTIONS

NG

6.CHECK AIR INJECTION SYSTEM PIPE CONNECTIONS
A386210

a.

Check that all the pipes and hoses between the air pump and ASV are securely connected.


b.

Inspect the pipes and hoses for blockages and damage.

OK:

AIR system piping has no blockages or damage.




OK

7.INSPECT AIR INJECTION CONTROL DRIVER (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE AIR INJECTION SYSTEM PIPING

7.INSPECT AIR INJECTION CONTROL DRIVER (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT)
a.

Disconnect the air injection control driver (AID) connectors.

A411085E01
0.865,1.031 1.281,1.313 0.417,0.281 0.896,2.792 1.313,3.073 0.417,0.281 3.958,1.031 4.375,1.313 0.417,0.281 3.885,2.844 4.302,3.125 0.417,0.281 1.281,1.573 1.677,1.302 true 1.281,3.333 1.677,3.063 true 4.594,3.458 4.802,3.021 true 4.667,1.646 4.875,1.208 true 5.708,3.49 5.51,3.031 true 5.698,1.677 5.5,1.219 true 0.677,0.083 2.958,0.521 2.281,0.438 10 false Front view of wire harness connector: (to AID for Bank 1) 0.781,1.844 3.063,2.281 2.281,0.438 10 false Front view of wire harness connector: (to AID for Bank 2) 4.219,0.094 6.5,0.531 2.281,0.438 10 false Front view of wire harness connector: (to AID for Bank 1) 4.219,1.865 6.5,2.302 2.281,0.438 10 false Front view of wire harness connector: (to AID for Bank 2) 0.927,1.094 1.542,1.292 0.615,0.198 10 false C173 4.021,1.094 4.635,1.292 0.615,0.198 10 false C174 0.948,2.844 1.563,3.042 0.615,0.198 10 false C175 3.938,2.906 4.552,3.104 0.615,0.198 10 false C176 0.906,1.521 1.521,1.719 0.615,0.198 10 false BATT 0.917,3.26 1.531,3.458 0.615,0.198 10 false BAT2 4.5,3.479 5.115,3.677 0.615,0.198 10 false E2 5.656,1.677 6.271,1.875 0.615,0.198 10 false +B 4.625,1.677 5.24,1.875 0.615,0.198 10 false E 5.635,3.521 6.25,3.719 0.615,0.198 10 false +B2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C174-1 (E) - Body ground Always Below 1 Ω
C176-1 (E2) - Body ground Always Below 1 Ω



c.

Turn the engine switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C173-1 (BATT) - Body ground Always 11 to 14 V (near battery voltage)
C174-5 (+B) - Body ground Engine switch on (IG) 11 to 14 V (near battery voltage)
C175-1 (BAT2) - Body ground Always 11 to 14 V (near battery voltage)
C176-5 (+B2) - Body ground Engine switch on (IG) 11 to 14 V (near battery voltage)




OK

8.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)

NG

REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT

8.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
a.

Disconnect the ECM connector.


b.

Disconnect the AID connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C45-63 (AIRP) - C174-4 (SIP) Always Below 1 Ω
C45-62 (ARP2) - C176-4 (SIP2) Always Below 1 Ω
C45-63 (AIRP) or C174-4 (SIP) - Body ground Always 10 kΩ or higher
C45-62 (ARP2) or C176-4 (SIP2) - Body ground Always 10 kΩ or higher




OK

9.INSPECT AIR PUMP (BANK 1 OR BANK 2)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT AIR PUMP (BANK 1 OR BANK 2)
a.
A218121E01
0.315,0.166 1.030,0.334 0.715,0.168 10 for Bank 1: 0.315,1.626 1.030,1.793 0.715,0.168 10 for Bank 2:

Start the engine and warm it up.


b.

Turn the engine switch off.


c.

Connect the 400 A probe of an ammeter to the positive (+) wire of the air pump.


d.

Connect the GTS to the DLC3.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Start the engine.


g.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



h.

Measure the current while the air pump is on and off.

Standard Current:
Tester Operation Air Pump ASV Specified Condition
AIR PUMP: ON, ASV: OPEN ON OPEN 10 to 40 A
AIR PUMP: OFF, ASV: CLOSE OFF CLOSE Below 1 A


NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While AIR system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR).

If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.





OK

10.PERFORM ACTIVE TEST USING GTS

NG

12.REPLACE AIR PUMP ASSEMBLY
10.PERFORM ACTIVE TEST USING GTS
a.

Disconnect the AID connectors.


A379565E13
0.875,2.75 1.292,3.01 0.417,0.26 4.052,2.792 4.469,3.052 0.417,0.26 1.656,2.927 1.49,3.24 true 1.771,2.927 1.698,3.24 true 1.896,2.927 2.01,3.229 true 2.01,2.917 2.302,3.229 true 4.927,2.958 4.76,3.271 true 5.052,2.958 5.031,3.292 true 5.198,2.958 5.396,3.281 true 5.344,2.969 5.698,3.26 true 0.479,0.385 1.552,0.583 1.073,0.198 10 false AID (for Bank 1) 2.542,0.396 2.958,0.583 0.417,0.188 10 false ECM 1.167,1.021 1.375,1.198 0.208,0.177 10 false DI 1.104,1.344 1.365,1.521 0.26,0.177 10 false SIV 2.479,1.021 2.813,1.198 0.333,0.177 10 false AIDI 2.479,1.354 2.854,1.531 0.375,0.177 10 false AIRV 0.781,1.865 3.073,2.25 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 1) 0.927,2.802 1.292,2.99 0.365,0.188 10 false C174 3.844,0.406 4.917,0.604 1.073,0.198 10 false AID (for Bank 2) 5.917,0.417 6.333,0.604 0.417,0.188 10 false ECM 4.406,1 4.667,1.188 0.26,0.188 10 false DI2 4.323,1.313 4.708,1.5 0.385,0.188 10 false SIV2 5.802,1 6.177,1.177 0.375,0.177 10 false AID2 5.792,1.313 6.208,1.49 0.417,0.177 10 false ARV2 1.406,3.271 1.573,3.479 0.167,0.208 10 false E 1.615,3.271 1.813,3.49 0.198,0.219 10 false DI 1.938,3.271 2.24,3.479 0.302,0.208 10 false SIV 2.281,3.26 2.583,3.469 0.302,0.208 10 false SIP 4.052,1.854 6.344,2.24 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 2) 4.104,2.844 4.49,3.031 0.385,0.188 10 false C176 4.646,3.292 4.885,3.469 0.24,0.177 10 false E2 4.948,3.313 5.198,3.49 0.25,0.177 10 false DI2 5.302,3.313 5.646,3.49 0.344,0.177 10 false SIV2 5.74,3.26 6.083,3.438 0.344,0.177 10 false SIP2

b.

Connect terminals DI and SIV or DI2 and SIV2 of the wire harness connector for the AID.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN or AIR PUMP 2: ON, ASV 2: OPEN.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



g.

Start the engine.


h.

Perform the AIR system forced operation while the engine is idling.


i.

Measure the voltage between the SIV and E or SIV2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.


j.

Turn the engine switch off.

NOTICE:
·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
C174-3 (SIV) - C174-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
C176-3 (SIV2) - C176-1 (E2) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
C174-3 (SIV) - C174-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V
C176-3 (SIV2) - C176-1 (E2) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



k.

Connect terminals DI and SIP or DI2 and SIP2 of the wire harness connector for the AID.

A379565E14
0.875,2.75 1.292,3.01 0.417,0.26 4.052,2.792 4.469,3.052 0.417,0.26 1.656,2.927 1.49,3.24 true 1.771,2.927 1.698,3.24 true 1.896,2.927 2.01,3.229 true 2.01,2.917 2.302,3.229 true 4.927,2.958 4.76,3.271 true 5.052,2.958 5.031,3.292 true 5.198,2.958 5.396,3.281 true 5.344,2.969 5.698,3.26 true 0.479,0.385 1.552,0.583 1.073,0.198 10 false AID (for Bank 1) 2.542,0.396 2.958,0.583 0.417,0.188 10 false ECM 1.167,1.021 1.375,1.198 0.208,0.177 10 false DI 1.094,1.344 1.354,1.521 0.26,0.177 10 false SIP 2.479,1.021 2.813,1.198 0.333,0.177 10 false AIDI 2.479,1.354 2.854,1.531 0.375,0.177 10 false AIRP 0.781,1.865 3.073,2.25 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 1) 0.927,2.802 1.323,2.99 0.396,0.188 10 false C174 3.844,0.406 4.917,0.604 1.073,0.198 10 false AID (for Bank 2) 5.917,0.417 6.333,0.604 0.417,0.188 10 false ECM 4.406,1 4.667,1.188 0.26,0.188 10 false DI2 4.333,1.313 4.708,1.5 0.375,0.188 10 false SIP2 5.802,1 6.177,1.177 0.375,0.177 10 false AID2 5.792,1.313 6.208,1.49 0.417,0.177 10 false ARP2 1.406,3.271 1.573,3.479 0.167,0.208 10 false E 1.615,3.271 1.813,3.49 0.198,0.219 10 false DI 1.938,3.271 2.24,3.479 0.302,0.208 10 false SIV 2.281,3.26 2.583,3.469 0.302,0.208 10 false SIP 4.052,1.854 6.344,2.24 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 2) 4.115,2.844 4.49,3.042 0.375,0.198 10 false C176 4.646,3.292 4.885,3.469 0.24,0.177 10 false E2 4.948,3.313 5.198,3.49 0.25,0.177 10 false DI2 5.302,3.313 5.646,3.49 0.344,0.177 10 false SIV2 5.74,3.26 6.083,3.438 0.344,0.177 10 false SIP2


l.

Connect the GTS to the DLC3.


m.

Turn the engine switch on (IG).


n.

Turn the GTS on.


o.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN or AIR PUMP 2: ON, ASV 2: OPEN.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



p.

Start the engine.


q.

Perform the AIR system forced operation while the engine is idling.


r.

Measure the voltage between the SIP and E or SIP2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.


s.

Turn the engine switch off.

NOTICE:
·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
C174-4 (SIP) - C174-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
C176-4 (SIP2) - C176-1 (E2) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
C174-4 (SIP) - C174-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V
C176-4 (SIP2) - C176-1 (E2) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V




OK

11.REPLACE AIR INJECTION CONTROL DRIVER (BANK 1 OR BANK 2)

NG

11.REPLACE AIR INJECTION CONTROL DRIVER (BANK 1 OR BANK 2)
a.


NEXT

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2447)
12.REPLACE AIR PUMP ASSEMBLY

NEXT

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2447)
13.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2447)
a.

Start the engine and warm it up.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG) and turn the GTS on.



f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.


g.

Start the engine after the GTS initialization is finished.


h.

Perform the System Check operation by pressing Next.


i.

After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.


j.

Refer to the confirmation driving pattern.


k.

Check pending DTCs.


l.

Turn the engine switch off.

OK:

No pending DTC is output.


NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.





OK

END

NG