Use the same procedures for LHD and RHD vehicles.
The procedures listed below are for LHD vehicles.
88474
1.INSTALL COOLER DRYER
Using pliers, install the cooler dryer.
Apply a sufficient amount of compressor oil to the contact surfaces of a new O-ring and the cap.
ND-OIL 8 or equivalent
Install O-ring to the cap.
Using a 14 mm socket hexagon wrench, install the cap to the modulator.
88460
2.INSTALL COOLER CONDENSER ASSEMBLY
Install the cooler condenser as shown in the illustration.
If the cooler condenser assembly is replaced with a new one, add compressor oil to the new cooler condenser assembly.
40 cc (1.35 fl.oz)
ND-OIL 8 or equivalent
53201
3.INSTALL RADIATOR SUPPORT SUB-ASSEMBLY
Install the radiator support with the 8 bolts.
16400
4.INSTALL RADIATOR ASSEMBLY
for 1UR-FE:
Click hereEngine / Hybrid System>1UR-FE (COOLING)>RADIATOR>INSTALLATION
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (COOLING)>RADIATOR>INSTALLATION
for 3UR-FE:
Click hereEngine / Hybrid System>3UR-FE (COOLING)>RADIATOR>INSTALLATION
for 1VD-FTV:
Click hereEngine / Hybrid System>1VD-FTV (COOLING)>RADIATOR>INSTALLATION
53510
5.INSTALL HOOD LOCK ASSEMBLY
53629
6.INSTALL HOOD LOCK CONTROL CABLE COVER
32910
7.CONNECT OIL COOLER ASSEMBLY (w/ Air Cooled Transmission Oil Cooler)
52521
8.INSTALL FRONT BUMPER CENTER UPPER RETAINER
for Standard:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(for Standard)>INSTALLATION
w/ Winch:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(w/ Winch)>INSTALLATION
53209B
9.INSTALL HOOD LOCK SUPPORT BRACE SUB-ASSEMBLY
Install the brace with the 3 bolts and nut.
53228A
10.INSTALL LOWER NO. 1 RADIATOR MOUNTING BRACKET
88590
11.INSTALL SHROUD BLOWER ASSEMBLY (w/ Rear Air Conditioning System)
86520
12.INSTALL LOW PITCHED HORN ASSEMBLY
86510
13.INSTALL HIGH PITCHED HORN ASSEMBLY
88716A
14.CONNECT COOLER REFRIGERANT LIQUID PIPE A
Remove the attached vinyl tape from the hose and the connecting part of the cooler condenser.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the pipe joint.
ND-OIL 8 or equivalent
Install O-ring on the liquid pipe A.
Connect the liquid pipe A to the cooler condenser with the bolt.
When tightening the bolt, do not allow any tools to contact the pipe.
When tightening the bolt, hold a part of the pipe near the connector.
88711
15.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
Remove the attached vinyl tape from the pipe and the connecting part of the cooler condenser.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the hose joint.
ND-OIL 8 or equivalent
Install O-ring on the discharge hose.
Connect the discharge hose to the cooler condenser with the 2 bolts.
When tightening the bolts, do not allow any tools to contact the pipe.
When tightening the bolts, hold a part of the pipe near the connector.
16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
17.CHARGE REFRIGERANT
18.WARM UP ENGINE
19.CHECK FOR REFRIGERANT GAS LEAK
20.CHECK SRS WARNING LIGHT
52119A
21.INSTALL FRONT BUMPER COVER
for Standard:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(for Standard)>INSTALLATION
w/ Winch:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(w/ Winch)>INSTALLATION