Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P001400  Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1  P001500  Camshaft Position "B" - Timing Over-Retarded Bank 1  P002400  Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 2  P002500  Camshaft Position "B" - Timing Over-Retarded Bank 2  


DESCRIPTION

Refer to DTC P001313.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P001313

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P001400 Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1 Exhaust valve timing is stuck at a certain value when in the advance range (2 trip detection logic).
·

Valve timing

·

Cam timing oil control solenoid assembly (for exhaust camshaft of bank 1)

·

Camshaft timing oil control valve assembly (bank 1) (exhaust camshaft timing gear bolt assembly)

·

Camshaft timing exhaust gear assembly (bank 1)

·

ECM


Comes on SAE: P0014
P001500 Camshaft Position "B" - Timing Over-Retarded Bank 1 Exhaust valve timing is stuck at a certain value when in the retard range (1 trip detection logic).
·

Valve timing

·

Cam timing oil control solenoid assembly (for exhaust camshaft of bank 1)

·

Camshaft timing oil control valve assembly (bank 1) (exhaust camshaft timing gear bolt assembly)

·

Camshaft timing exhaust gear assembly (bank 1)

·

ECM


Comes on SAE: P0015
P002400 Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 2 Exhaust valve timing is stuck at a certain value when in the advance range (2 trip detection logic).
·

Valve timing

·

Cam timing oil control solenoid assembly (for exhaust camshaft of bank 2)

·

Camshaft timing oil control valve assembly (bank 2) (exhaust camshaft timing gear bolt assembly)

·

Camshaft timing exhaust gear assembly (bank 2)

·

ECM


Comes on SAE: P0024
P002500 Camshaft Position "B" - Timing Over-Retarded Bank 2 Exhaust valve timing is stuck at a certain value when in the retard range (1 trip detection logic).
·

Valve timing

·

Cam timing oil control solenoid assembly (for exhaust camshaft of bank 2)

·

Camshaft timing oil control valve assembly (bank 2) (exhaust camshaft timing gear bolt assembly)

·

Camshaft timing exhaust gear assembly (bank 2)

·

ECM


Comes on SAE: P0025

MONITOR DESCRIPTION

The ECM optimizes the exhaust valve timing using the Variable Valve Timing (VVT) system to control the exhaust camshaft. The VVT system includes the ECM, cam timing oil control solenoid assembly (for exhaust camshaft), camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) and camshaft timing exhaust gear assembly. The ECM sends a target duty-cycle control signal to the cam timing oil control solenoid assembly (for exhaust camshaft). The camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) is operated to control the oil pressure supplied to the camshaft timing exhaust gear assembly based on this signal. The camshaft timing intake gear assembly can advance or retard the exhaust camshaft.

If the difference between the target and actual exhaust valve timing is large, and changes in the actual exhaust valve timing are small, the ECM interprets this as the camshaft timing exhaust gear assembly stuck malfunction and stores a DTC.

Example:

A DTC is stored when the following conditions are met:

(a)

It takes 5 seconds or more to change the valve timing by 5°CA.

(b)

After the above condition is met, the cam timing oil control solenoid assembly (for exhaust camshaft) is forcibly activated for 9.5 seconds.



These DTCs indicate that the camshaft timing exhaust gear assembly cannot operate properly due to a camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) malfunction or the presence of foreign matter in the camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly).

MONITOR STRATEGY

Required Sensors/Components (Main) Cam timing oil control solenoid assembly (for exhaust camshaft)
Camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly)
Camshaft timing exhaust gear assembly
Required Sensors/Components (Related) Crankshaft position sensor
Camshaft position sensor
Engine coolant temperature sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A384199E24
3.708,3.427 3.865,3.427 3.865,3.427 4.135,2.646 false 6.177,3.354 6.333,3.354 6.333,3.354 6.688,2.625 false 2.458,0.063 6.969,0.99 4.51,0.927 10 false *: Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (depress the accelerator pedal by a large amount) and then decelerating the vehicle 10 to 15 times. 0.208,0.469 1.146,0.813 0.938,0.344 10 false Vehicle Speed 0.208,1.094 1.115,1.469 0.906,0.375 10 false Approximately 60 km/h 0.719,2.115 1.427,2.49 0.708,0.375 10 false Idling 0.188,2.365 1.083,2.75 0.896,0.385 10 false Ignition Switch ON 1.375,2.354 2.083,2.729 0.708,0.375 10 false [A] 1.615,2.771 2.438,3.115 0.823,0.344 10 false Warming up 2.563,2.781 3.813,3.052 1.25,0.271 10 false 10 minutes or more 2.542,3.333 3.896,3.625 1.354,0.292 10 false 3 minutes or more 1.865,2.042 2.573,2.417 0.708,0.375 10 false [B] 2.99,1.021 3.698,1.396 0.708,0.375 10 false [C] 4.021,2.333 4.729,2.708 0.708,0.375 10 false [D] 4.25,3.167 4.604,3.417 0.354,0.25 10 false [E] 5.458,2.25 5.813,2.5 0.354,0.25 10 false [F]* 6.583,2.323 6.938,2.573 0.354,0.25 10 false [G] 6.823,3.167 7.094,3.417 0.271,0.25 10 false [H] 5.021,3.271 6.375,3.563 1.354,0.292 10 false 3 minutes or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

9.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Idle the engine for 3 minutes or more [D].

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P001400, P001500, P002400 or P002500.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [F] through [H].



16.

Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Depress the accelerator pedal by a large amount.


17.

Idle the engine for 3 minutes or more [G].

18.

Enter the following menus: Powertrain / Engine / Trouble Codes [H].

19.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



20.

Check the DTC judgment result again.

HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

DTC P001400, P001500, P002400 or P002500 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. This foreign matter may then be captured by the oil filter.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

Timing Over Advanced
(Valve timing is out of specified range)
Timing Over Retarded
(Valve timing is out of specified range)
Suspected Area
P001400 P001500 Bank 1
P002400 P002500 Bank 2



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001400, P001500, P002400 OR P002500)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P001400, P001500, P002400 or P002500 is output A
P001400, P001500, P002400 or P002500 and other DTCs are output B


HINT:

If any DTCs other than P001400, P001500, P002400 or P002500 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO)

B

GO TO DTC CHART

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO)
a.

Start the engine.


b.

Check the engine speed while operating the cam timing oil control solenoid assembly (for exhaust camshaft) using the GTS.

Powertrain > Engine > Active Test
Tester Display
Control the Exhaust VVT OCV Duty Ratio Bank 1
50004 372 5
Powertrain > Engine > Active Test
Tester Display
Control the Exhaust VVT OCV Duty Ratio Bank 2
50004 372 46
OK:
GTS Operation Engine Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:

Refer to "Data List / Active Test" [Exhaust VVT Hold Learn Value Bank 1, Exhaust VVT Change Angle Bank 1, Exhaust VVT OCV Control Duty Ratio Bank 1 and Exhaust VVT Target Angle Bank 1 or Exhaust VVT Hold Learn Value Bank 2, Exhaust VVT Change Angle Bank 2, Exhaust VVT OCV Control Duty Ratio Bank 2 and Exhaust VVT Target Angle Bank 2].

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

5.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)
3.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P001400, P001500, P002400 or P002500 is output B


HINT:

DTC P001400, P001500, P002400 or P002500 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.




A

B

5.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)
5.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)

OK

6.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)

NG

8.REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)
6.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)

OK

7.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)

NG

10.REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)
7.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
a.

Remove the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.

A472469C01
5.802,0.688 6.552,0.594 false 6.552,0.594 6.74,1.51 false 0.667,0.604 1.521,0.813 false 0.458,1.573 0.656,0.604 false 0.885,2.458 1.083,2.458 1.083,2.458 1.292,2.948 false 6.792,3.094 6.948,3.094 6.948,3.094 6.885,3.74 false 6.177,2.479 6.021,2.479 6.021,2.479 5.896,2.969 false 0.323,3.104 0.156,3.104 0.156,3.104 0.292,3.74 false 3.573,4.365 3.99,4.052 3.99,4.052 4.219,4.052 false 0.49,0.469 0.802,0.625 0.313,0.156 10 false *a 0.365,3.021 0.677,3.177 0.313,0.156 10 false *b 0.688,2.385 1,2.542 0.313,0.156 10 false *c 6.229,2.427 6.542,2.583 0.313,0.156 10 false *d 6.625,3.021 6.875,3.219 0.25,0.198 10 false *e 6.563,0.438 6.875,0.594 0.313,0.156 10 false *a 4.24,3.958 4.448,4.177 0.208,0.219 10 true *a
*a Timing Mark *b Approximately 48°
*c Approximately 17° *d Approximately 14°
*e Approximately 50° - -



b.

Turn the crankshaft pulley and align its groove with the TDC timing mark of the timing chain cover.


c.

Check that the timing marks of the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are at the positions shown in the illustration.

HINT:

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.


OK:

Timing marks on camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are at the positions shown in the illustration.


HINT:

If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.



Result:
Proceed to
OK
NG



OK

12.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

8.REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)

NEXT

9.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)
9.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)

OK

11.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO)

NG

10.REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)
10.REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)

NEXT

11.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO)
11.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO)
a.

Start the engine.


b.

Check the engine speed while operating the cam timing oil control solenoid assembly (for exhaust camshaft) using the GTS.

Powertrain > Engine > Active Test
Tester Display
Control the Exhaust VVT OCV Duty Ratio Bank 1
50004 372 5
Powertrain > Engine > Active Test
Tester Display
Control the Exhaust VVT OCV Duty Ratio Bank 2
50004 372 46
OK:
GTS Operation Engine Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:

Refer to "Data List / Active Test" [Exhaust VVT Hold Learn Value Bank 1, Exhaust VVT Change Angle Bank 1, Exhaust VVT OCV Control Duty Ratio Bank 1 and Exhaust VVT Target Angle Bank 1 or Exhaust VVT Hold Learn Value Bank 2, Exhaust VVT Change Angle Bank 2, Exhaust VVT OCV Control Duty Ratio Bank 2 and Exhaust VVT Target Angle Bank 2].

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

END

NG

12.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
12.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Click hereEngine / Hybrid System>V35A-FTS (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC
13.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)
14.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P001400, P001500, P002400 or P002500 is output B




A

END

B