| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | ENGINE WATER PUMP ASSEMBLY | 16100 | ( ) |
- | - |
| 2 | CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY | - | ( ) |
- | - |
| 3 | CYLINDER BLOCK WATER DRAIN COCK PLUG | - | - | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent | ★ | Precoated part |
|
Do not apply lubricants to the threads parts | - | - |
| *1 | NO. 4 WATER BY-PASS HOSE | *2 | NO. 9 WATER BY-PASS HOSE |
| *3 | NO. 2 AIR TUBE SUPPORT | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
| *1 | FLUID COUPLING ASSEMBLY WITH FAN | *2 | FAN PULLEY |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| *1 | ENGINE SIDE COVER SUB-ASSEMBLY LH | *2 | ENGINE SIDE COVER SUB-ASSEMBLY RH |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
16100 1.INSTALL ENGINE WATER PUMP ASSEMBLY
|
Bolt A |
|
Bolt B |
|
Bolt C | - | - |
Temporarily install a new engine water pump gasket with the 9 bolts.
Make sure that there is no oil on the threads of the bolts A and B.
Do not reuse the gasket.
| Item | Length |
|---|---|
| Bolt A | 80 mm (3.15 in.) |
| Bolt B | 55 mm (2.17 in.) |
| Bolt C | 14 mm (0.551 in.) |
|
Bolt A |
|
Bolt B |
Temporarily install the engine water pump assembly with the 10 bolts.
Make sure that there is no oil on the threads of the bolts A.
| Item | Length |
|---|---|
| Bolt A | 90 mm (3.54 in.) |
| Bolt B | 25 mm (0.984 in.) |
|
Bolt A |
|
Bolt B |
Tighten the 10 bolts in the order shown in the illustration.
Tighten the 9 bolts to install the engine water pump gasket and engine water pump assembly.
2.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
|
|
| *a | Adhesive | *b | Pipe |
| *c | 60° | - | - |
Apply adhesive to the threaded part.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
After applying adhesive 1344, install the cylinder block water drain cock sub-assembly within 3 minutes.
Install the cylinder block water drain cock sub-assembly to the engine water pump assembly as shown in the illustration.
After tightening to the specified torque, if the pipe of the cylinder block water drain cock sub-assembly does not come within the range shown in the illustration, retighten it again and set it to the range shown in the illustration.
Make sure the tightening angle is within 360°. (Upper torque limit: 45 N*m (459 kgf*cm, 33 ft.*lbf))
Be sure to check the torque and perform further tightening within 30 minutes after tightening is completed.
Do not loosen after tightening.
3.INSTALL CYLINDER BLOCK WATER DRAIN COCK PLUG
16620D 4.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
17368G 19.INSTALL NO. 1 AIR TUBE SUPPORT
82121 20.CONNECT ENGINE WIRE
16278 25.CONNECT NO. 2 WATER BY-PASS PIPE
44369A 28.INSTALL NO. 1 OIL RESERVOIR BRACKET
35.ADD ENGINE COOLANT
36.ADD COOLANT (for Intercooler)
37.INSPECT FOR COOLANT LEAK
38.INSPECT FOR COOLANT LEAK (for Intercooler)
51410 39.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
11209 40.INSTALL V-BANK COVER SUB-ASSEMBLY