Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2021.07–2022.11
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467519 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0122  CAN Communication Error (VSC)  U012987  Lost Communication With Brake System Control Module Missing Message  U115987  Lost Communication with Electronic Brake Booster Control Module "A" (ch3) Missing Message  U115C00  Lost Communication with ECM/PCM "A" (ch5)  U115C87  Lost Communication with ECM/PCM "A" (ch5) Missing Message  U117087  Lost Communication With Brake System Control Module(ch2) Missing Message  U117D87  Lost Communication with Brake System Control Module (ch4) Missing Message  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
U0122 CAN Communication Error (VSC) The DTC output ECU does not receive data from the brake actuator assembly (No. 2 skid control ECU).
·

CAN main/branch bus lines or connector

·

ECM

·

Engine stop and start ECU (w/ Stop and Start System)

·

Absorber control ECU (w/ Adaptive Variable Suspension System)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

Brake actuator assembly (No. 2 skid control ECU)

·

No. 1 Global CAN Junction Connector (for LHD)

·

No. 7 Global CAN Junction Connector (for LHD)

·

No. 1 CAN junction connector (for RHD)

·

No. 2 CAN junction connector (for RHD)


Adaptive Variable Suspension System A
U012987 Lost Communication With Brake System Control Module Missing Message The DTC output ECU does not receive data from the brake actuator assembly (No. 2 skid control ECU).
·

CAN main/branch bus lines or connector

·

ECM

·

Engine stop and start ECU (w/ Stop and Start System)

·

Absorber control ECU (w/ Adaptive Variable Suspension System)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

Brake actuator assembly (No. 2 skid control ECU)

·

No. 1 Global CAN Junction Connector (for LHD)

·

No. 7 Global CAN Junction Connector (for LHD)

·

No. 1 CAN junction connector (for RHD)

·

No. 2 CAN junction connector (for RHD)


Engine A
U115987 Lost Communication with Electronic Brake Booster Control Module "A" (ch3) Missing Message The DTC output ECU does not receive data from the brake booster with master cylinder assembly (No. 1 skid control ECU).
·

CAN main/branch bus lines or connector

·

ECM

·

Engine stop and start ECU (w/ Stop and Start System)

·

Absorber control ECU (w/ Adaptive Variable Suspension System)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

Brake actuator assembly (No. 2 skid control ECU)

·

No. 1 Global CAN Junction Connector (for LHD)

·

No. 7 Global CAN Junction Connector (for LHD)

·

No. 1 CAN junction connector (for RHD)

·

No. 2 CAN junction connector (for RHD)


Brake/EPB A
U115C00 Lost Communication with ECM/PCM "A" (ch5) The DTC output ECU does not receive data from the ECM.
·

CAN main/branch bus lines or connector

·

ECM

·

Engine stop and start ECU (w/ Stop and Start System)

·

Absorber control ECU (w/ Adaptive Variable Suspension Sysem)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

Brake actuator assembly (No. 2 skid control ECU)

·

No. 1 Global CAN Junction Connector (for LHD)

·

No. 7 Global CAN Junction Connector (for LHD)

·

No. 1 CAN junction connector (for RHD)

·

No. 2 CAN junction connector (for RHD)


Brake Booster A
U115C87 Lost Communication with ECM/PCM "A" (ch5) Missing Message The DTC output ECU does not receive data from the ECM.
·

CAN main/branch bus lines or connector

·

ECM

·

Engine stop and start ECU (w/ Stop and Start System)

·

Absorber control ECU (w/ Adaptive Variable Suspension Sysem)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

Brake actuator assembly (No. 2 skid control ECU)

·

No. 1 Global CAN Junction Connector (for LHD)

·

No. 7 Global CAN Junction Connector (for LHD)

·

No. 1 CAN junction connector (for RHD)

·

No. 2 CAN junction connector (for RHD)


Brake/EPB A
U117087 Lost Communication With Brake System Control Module(ch2) Missing Message The DTC output ECU does not receive data from the brake actuator assembly (No. 2 skid control ECU).
·

CAN main/branch bus lines or connector

·

ECM

·

Engine stop and start ECU (w/ Stop and Start System)

·

Absorber control ECU (w/ Adaptive Variable Suspension Sysem)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

Brake actuator assembly (No. 2 skid control ECU)

·

No. 1 Global CAN Junction Connector (for LHD)

·

No. 7 Global CAN Junction Connector (for LHD)


Stop and Start A
U117D87 Lost Communication with Brake System Control Module (ch4) Missing Message The DTC output ECU does not receive data from the brake actuator assembly (No. 2 skid control ECU).
·

CAN main/branch bus lines or connector

·

ECM

·

Engine stop and start ECU (w/ Stop and Start System)

·

Absorber control ECU (w/ Adaptive Variable Suspension Sysem)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

Brake actuator assembly (No. 2 skid control ECU)

·

No. 1 Global CAN Junction Connector (for LHD)

·

No. 7 Global CAN Junction Connector (for LHD)

·

No. 1 CAN junction connector (for RHD)

·

No. 2 CAN junction connector (for RHD)


Brake Booster A

WIRING DIAGRAM

for LHD
C464921E02
5.188,1.229 7.156,1.594 1.969,0.365 10 false Central Gateway ECU (Network Gateway ECU) 5.208,1.063 6.417,1.271 1.208,0.208 10 false I42 5.917,0.927 6.385,1.094 0.469,0.167 10 false CAWL 0.906,0.198 1.417,0.448 0.51,0.25 10 false CA2H 5.646,0.708 5.958,0.906 0.313,0.198 10 false 13 5.646,0.219 5.958,0.417 0.313,0.198 10 false 12 4.104,0.219 4.313,0.479 0.208,0.26 10 false 1 3.688,0.219 4,0.417 0.313,0.198 10 false 2 5.208,0.219 5.51,0.406 0.302,0.188 10 false 3 5.333,2.823 5.646,3.021 0.313,0.198 10 false I57 4.042,0.708 4.354,0.906 0.313,0.198 10 false 12 5.198,0.708 5.51,0.906 0.313,0.198 10 false 14 0.927,0.927 1.625,1.188 0.698,0.26 10 false CA2L 5.927,2.604 6.542,2.802 0.615,0.198 10 false LC1L 0.031,1.031 0.49,1.229 0.458,0.198 10 false B20 0.625,4.917 1.177,5.167 0.552,0.25 10 false ECM 5.208,1.917 5.365,2.115 0.156,0.198 10 false 5 2.542,0.24 2.854,0.438 0.313,0.198 10 false 1 5.917,0.208 6.531,0.406 0.615,0.198 10 false CAWH 5.906,2.021 6.521,2.219 0.615,0.198 10 false LC1H 5.198,2.521 5.51,2.719 0.313,0.198 10 false 16 2.573,1.958 2.885,2.156 0.313,0.198 10 false 3 2.479,5.031 2.75,5.208 0.271,0.177 10 false B66 5.552,4.813 7.156,5.323 1.604,0.51 10 false Absorber Control ECU*4 2.469,0.708 2.802,0.969 0.333,0.26 10 false 12 2.573,3.719 2.885,3.917 0.313,0.198 10 false 4 5.646,1.938 5.958,2.135 0.313,0.198 10 false 15 1.375,0.708 1.688,0.906 0.313,0.198 10 false 17 0.063,2.979 2.281,3.375 2.219,0.396 10 false Brake Booster with Master Cylinder Assembly (No. 1 Skid Control ECU) 5.656,3.729 5.885,3.948 0.229,0.219 10 false 19 5.667,4.323 5.979,4.521 0.313,0.198 10 false 18 5.188,4.302 5.469,4.51 0.281,0.208 10 false 13 5.208,3.74 5.521,3.938 0.313,0.198 10 false 2 5.927,4.406 6.542,4.604 0.615,0.198 10 false CA2L 5.917,3.833 6.531,4.031 0.615,0.198 10 false CA2H 0.031,2.802 0.521,3.01 0.49,0.208 10 false B19 0.073,1.229 1.656,1.583 1.583,0.354 10 false Brake Actuator Assembly (No. 2 Skid Control ECU) 5.552,4.646 6.167,4.844 0.615,0.198 10 false Q11 4.26,5.198 5.906,5.552 1.646,0.354 10 false No. 7 Global CAN Junction Connector 0.875,2.052 1.49,2.25 0.615,0.198 10 false CA2H 0.885,2.615 1.5,2.813 0.615,0.198 10 false CA2L 5.323,2.99 7.146,3.292 1.823,0.302 10 false Engine Stop and Start ECU*3 2.479,5.198 4.135,5.604 1.656,0.406 10 false No. 1 Global CAN Junction Connector 5.656,2.521 5.969,2.719 0.313,0.198 10 false 16 3.688,0.708 4,0.906 0.313,0.198 10 false 13 1.375,0.229 1.688,0.427 0.313,0.198 10 false 16 4.26,5.021 4.542,5.198 0.281,0.177 10 false I118 2.479,2.521 2.813,2.781 0.333,0.26 10 false 14 1.365,1.958 1.667,2.156 0.302,0.198 10 false 35 1.365,2.531 1.667,2.729 0.302,0.198 10 false 36 2.49,4.292 2.802,4.49 0.313,0.198 10 false 15 1.354,3.74 1.656,3.927 0.302,0.188 10 false 10 1.365,4.292 1.656,4.51 0.292,0.219 10 false 18 0.677,4.75 1.094,4.99 0.417,0.24 10 false B2 0.844,3.854 1.458,4.052 0.615,0.198 10 false CANP 0.833,4.417 1.448,4.615 0.615,0.198 10 false CANN 2.656,6.406 4.802,6.604 2.146,0.198 10 false *1: for 1GR-FE 2.656,6.865 4.802,7.063 2.146,0.198 10 false *2: for V35A-FTS 2.656,7.313 4.802,7.51 2.146,0.198 10 false *3: w/ Stop and Start System 4.344,6.375 7.156,6.688 2.813,0.313 10 false *4: w/ Adaptive Variable Suspension System 0.625,6.625 1.177,6.875 0.552,0.25 10 false ECM 0.844,5.656 1.458,5.854 0.615,0.198 10 false CACH 0.854,6.271 1.469,6.469 0.615,0.198 10 false CACL 1.427,5.667 1.656,5.844 0.229,0.177 10 false B1 1.427,6.26 1.781,6.438 0.354,0.177 10 false B1 1.792,6.26 2.115,6.438 0.323,0.177 10 false B70 1.792,5.667 2.083,5.844 0.292,0.177 10 false B70 1.427,5.448 1.719,5.667 0.292,0.219 10 false 16 1.844,5.448 2.052,5.646 0.208,0.198 10 false 17 1.427,6.052 1.781,6.229 0.354,0.177 10 false 15 1.844,6.063 2.042,6.26 0.198,0.198 10 false 16 1.417,6.49 1.708,6.677 0.292,0.188 10 false *2 1.438,5.885 1.729,6.073 0.292,0.188 10 false *2 1.813,6.49 2.104,6.677 0.292,0.188 10 false *5 1.823,5.896 2.115,6.083 0.292,0.188 10 false *5 4.333,6.833 6.479,7.031 2.146,0.198 10 false *5: for F33A-FTV 1.75,3.74 2.042,3.927 0.292,0.188 10 false *1 1.74,4.302 2.031,4.49 0.292,0.188 10 false *1

for RHD
C464922E03
5.208,1.865 7.156,2.469 1.948,0.604 10 false Central Gateway ECU (Network Gateway ECU) 5.208,1.698 6.417,1.906 1.208,0.208 10 false I42 5.74,1.438 6.208,1.604 0.469,0.167 10 false CAWL 0.906,0.698 1.417,0.948 0.51,0.25 10 false CA2H 5.51,1.198 5.823,1.396 0.313,0.198 10 false 13 5.5,0.708 5.813,0.906 0.313,0.198 10 false 12 3.875,0.719 4.083,0.979 0.208,0.26 10 false 2 3.542,0.719 3.854,0.917 0.313,0.198 10 false 2 5.125,0.729 5.427,0.917 0.302,0.188 10 false 1 3.802,1.198 4.115,1.396 0.313,0.198 10 false 13 5.104,1.198 5.417,1.396 0.313,0.198 10 false 12 0.948,1.406 1.646,1.667 0.698,0.26 10 false CA2L 0.104,1.74 0.563,1.938 0.458,0.198 10 false B20 0.594,6.708 1.198,7.01 0.604,0.302 10 false ECM 5.115,3.177 5.271,3.375 0.156,0.198 10 false 3 2.292,0.698 2.604,0.896 0.313,0.198 10 false 1 5.729,0.698 6.344,0.896 0.615,0.198 10 false CAWH 5.104,3.646 5.417,3.844 0.313,0.198 10 false 14 2.281,3.156 2.594,3.354 0.313,0.198 10 false 3 2.375,6.74 2.833,6.938 0.458,0.198 10 false B48 5.479,4.354 7.156,4.844 1.677,0.49 10 false Absorber Control ECU*1 2.24,1.177 2.573,1.438 0.333,0.26 10 false 12 2.292,5.573 2.604,5.771 0.313,0.198 10 false 4 5.521,3.177 5.833,3.375 0.313,0.198 10 false 19 1.385,1.167 1.698,1.365 0.313,0.198 10 false 17 0.094,4.354 2.313,4.75 2.219,0.396 10 false Brake Booster with Master Cylinder Assembly (No. 1 Skid Control ECU) 5.771,3.75 6.385,3.948 0.615,0.198 10 false CA2L 5.76,3.26 6.375,3.458 0.615,0.198 10 false CA2H 0.094,4.198 0.583,4.406 0.49,0.208 10 false B19 0.104,1.885 1.698,2.25 1.594,0.365 10 false Brake Actuator Assembly (No. 2 Skid Control ECU) 5.469,4.177 6.083,4.375 0.615,0.198 10 false Q11 3.969,4.833 5.219,5.208 1.25,0.375 10 false No. 1 CAN Junction Connector 0.771,3.281 1.385,3.479 0.615,0.198 10 false CA2H 0.792,3.771 1.406,3.969 0.615,0.198 10 false CA2L 2.375,6.917 3.604,7.365 1.229,0.448 10 false No. 2 CAN Junction Connector 5.51,3.667 5.823,3.865 0.313,0.198 10 false 18 3.521,1.198 3.833,1.396 0.313,0.198 10 false 13 1.385,0.698 1.698,0.896 0.313,0.198 10 false 16 3.958,4.604 4.417,4.802 0.458,0.198 10 false I116 2.229,3.625 2.563,3.885 0.333,0.26 10 false 14 1.229,3.177 1.531,3.375 0.302,0.198 10 false 35 1.219,3.646 1.521,3.844 0.302,0.198 10 false 36 2.229,6.219 2.542,6.417 0.313,0.198 10 false 15 1.354,5.469 1.604,5.646 0.25,0.177 10 false 16 1.771,6.104 1.969,6.281 0.198,0.177 10 false 18 0.802,5.74 1.417,5.938 0.615,0.198 10 false CACH 0.813,6.333 1.427,6.531 0.615,0.198 10 false CACL 4.188,6.219 6.938,6.448 2.75,0.229 10 false *1: w/ Adaptive Variable Suspension System 1.771,5.469 1.99,5.677 0.219,0.208 10 false 17 1.354,6.115 1.604,6.292 0.25,0.177 10 false 15 1.354,6.563 1.604,6.74 0.25,0.177 10 false *2 1.771,6.573 2.021,6.75 0.25,0.177 10 false *3 1.76,5.906 2.01,6.083 0.25,0.177 10 false *3 1.354,5.917 1.604,6.094 0.25,0.177 10 false *2 1.344,5.677 1.563,5.854 0.219,0.177 10 false B1 1.354,6.323 1.667,6.521 0.313,0.198 10 false B1 1.729,5.677 2.042,5.875 0.313,0.198 10 false B70 1.719,6.323 2.01,6.51 0.292,0.188 10 false B70 4.188,6.781 5.302,7 1.115,0.219 10 false *2: for V35A-FTS 4.188,7.281 7.156,7.854 2.969,0.573 10 false *3: for F33A-FTV

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Check for DTCs.

Display on GTS / Output DTC Pattern
Pattern 1 Pattern 2 Pattern 3
Engine U012987 - ○ ○ - -
Adaptive Variable Suspension System U0122 - - - ○ -
Stop and Start U117087 - - - - ○
Brake Booster U115C00 ○ - ○ - -
U117D87 - - - - -
Brake/EPB U115C87 ○ - ○ - -
U115987 - - - - -

Display on GTS / Output DTC Pattern
Pattern 4 Pattern 5
Engine U012987 - - ○ - ○
Adaptive Variable Suspension System U0122 - - ○ - ○
Stop and Start U117087 - - ○ - ○
Brake Booster U115C00 ○ ○ - - -
U117D87 ○ ○ ○ - ○
Brake/EPB U115C87 - - ○ ○ -
U115987 ○ - ○ ○ -


Result:
Result Proceed to
Pattern 1 A
Pattern 2 B
Pattern 3 C
Pattern 4 D
Pattern 5 E
Other Pattern F



A

2.CHECK FOR OPEN IN CAN BUS LINES (ECM BRANCH LINE)

B

3.CHECK FOR OPEN IN CAN BUS LINES (ABSORBER CONTROL ECU BRANCH LINE)

C

4.CHECK FOR OPEN IN CAN BUS LINES (ENGINE STOP AND START ECU BRANCH LINE)

D

5.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU] BRANCH LINE)

E

6.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU] MAIN LINE)

F

7.CHECK VEHICLE TYPE
2.CHECK FOR OPEN IN CAN BUS LINES (ECM BRANCH LINE)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the B2*1, B1*2 or B70*3 ECM connector.

*1: for 1GR-FE

*2: for V35A-FTS

*3: for F33A-FTV



Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE
Tester Connection Condition Specified Condition

Click Location & Routing(B2)Location & Routing

Click Connector(B2)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B2-10 (CANP) - B2-18 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

for V35A-FTS
Tester Connection Condition Specified Condition

Click Location & Routing(B1)Location & Routing

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B1-16 (CACH) - B1-15 (CACL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

for F33A-FTV
Tester Connection Condition Specified Condition

Click Location & Routing(B70)Location & Routing

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B70-17 (CACH) - B70-18 (CACL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (for 1GR-FE) A
OK (for V35A-FTS) B
OK (for F33A-FTV) C
NG D


Post-procedure1

d.

None



A

B

C

D

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR

3.CHECK FOR OPEN IN CAN BUS LINES (ABSORBER CONTROL ECU BRANCH LINE)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the Q11 absorber control ECU connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q11)Location & Routing

Click Connector(Q11)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Absorber Control ECU

Q11-19 (CA2H) - Q11-18 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

REPLACE ABSORBER CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR

4.CHECK FOR OPEN IN CAN BUS LINES (ENGINE STOP AND START ECU BRANCH LINE)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I57 engine stop and start ECU connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I57)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

I57-15 (LC1H) - I57-16 (LC1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR

5.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU] BRANCH LINE)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the B19 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B19)Location & Routing

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

B19-35 (CA2H) - B19-36 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR

6.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU] MAIN LINE)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the B20 brake actuator assembly (No. 2 skid control ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-16 (CA2H) - B20-17 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 109 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN MAIN LINES OR CONNECTOR

7.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

8.CHECK FOR OPEN IN CAN BUS WIRE

B

66.CHECK FOR OPEN IN CAN BUS WIRE
8.CHECK FOR OPEN IN CAN BUS WIRE
NOTICE:

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.


HINT:

Operating the ignition switch, any other switches or door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C458715C08
1.51,0.073 1.927,0.323 0.417,0.25 0.552,1.667 0.74,1.667 0.74,1.667 1.052,0.781 true 0.75,1.896 0.938,1.896 0.938,1.896 1.167,0.781 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.625,0.115 2.083,0.313 0.458,0.198 10 false I42 0.135,1.552 0.604,1.771 0.469,0.219 10 false CAWL 0.26,1.823 0.823,2.073 0.563,0.25 10 false CAWH
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-12 (CAWH) - I42-13 (CAWL) Cable disconnected from negative (-) battery terminal Below 70 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK FOR SHORT IN CAN BUS WIRES

NG

60.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
9.CHECK FOR SHORT IN CAN BUS WIRES
a.
C458715C08
1.51,0.073 1.927,0.323 0.417,0.25 0.552,1.667 0.74,1.667 0.74,1.667 1.052,0.781 true 0.75,1.896 0.938,1.896 0.938,1.896 1.167,0.781 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.625,0.115 2.083,0.313 0.458,0.198 10 false I42 0.135,1.552 0.604,1.771 0.469,0.219 10 false CAWL 0.26,1.823 0.823,2.073 0.563,0.25 10 false CAWH
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-12 (CAWH) - I42-13 (CAWL) Cable disconnected from negative (-) battery terminal 54 Ω or higher



Result:
Proceed to
OK
NG



OK

10.CHECK FOR SHORT TO B+ IN CAN BUS WIRE

NG

44.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
10.CHECK FOR SHORT TO B+ IN CAN BUS WIRE
a.
C458715C08
1.51,0.073 1.927,0.323 0.417,0.25 0.552,1.667 0.74,1.667 0.74,1.667 1.052,0.781 true 0.75,1.896 0.938,1.896 0.938,1.896 1.167,0.781 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.625,0.115 2.083,0.313 0.458,0.198 10 false I42 0.135,1.552 0.604,1.771 0.469,0.219 10 false CAWL 0.26,1.823 0.823,2.073 0.563,0.25 10 false CAWH
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42,I76)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I42-12 (CAWH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I42-13 (CAWL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

11.CHECK FOR SHORT TO GND IN CAN BUS WIRE

NG

28.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
11.CHECK FOR SHORT TO GND IN CAN BUS WIRE
a.
C458715C08
1.51,0.073 1.927,0.323 0.417,0.25 0.552,1.667 0.74,1.667 0.74,1.667 1.052,0.781 true 0.75,1.896 0.938,1.896 0.938,1.896 1.167,0.781 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.625,0.115 2.083,0.313 0.458,0.198 10 false I42 0.135,1.552 0.604,1.771 0.469,0.219 10 false CAWL 0.26,1.823 0.823,2.073 0.563,0.25 10 false CAWH
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42,I76)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I42-12 (CAWH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-13 (CAWL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I118 No. 7 global CAN junction connector.


Procedure1


Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

OK

14.CHECK VEHICLE TYPE

NG

25.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
14.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Adaptive Variable Suspension System A
w/o Adaptive Variable Suspension System B



A

15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

B

16.CHECK VEHICLE TYPE
15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

OK

16.CHECK VEHICLE TYPE

NG

26.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)
16.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B



A

17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

B

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

OK

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

NG

27.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the B66 No. 1 global CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66,I76)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B66-2 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B66-13 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

19.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)

19.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66,I76)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B66-1 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B66-12 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

NG

22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])
20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66,I76)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B66-3 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B66-14 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

21.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ECM)

NG

23.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])
21.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66,I76)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B66-4 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B66-15 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

24.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ECM)
22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

Pre-procedure1

a.

Disconnect the B20 brake actuator assembly (No.2 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66,I76)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B66-1 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B66-12 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

23.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

Pre-procedure1

a.

Disconnect the B19 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66,I76)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B66-3 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B66-14 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

24.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ECM)

Pre-procedure1

a.

Disconnect the B1*1, B2*2 or B70*3 ECM connector.

*1: for V35A-FTS

*2: for 1GR-FE

*3: for F33A-FTV



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66,I76)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B66-4 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B66-15 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ECM)

25.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

Pre-procedure1

a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


Procedure1


Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

26.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

Pre-procedure1

a.

Disconnect the Q11 absorber control ECU connector.


Procedure1


Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE ABSORBER CONTROL ECU

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

27.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

Pre-procedure1

a.

Disconnect the I57 engine stop and start ECU connector.


Procedure1


Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

28.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I118 No. 7 global CAN junction connector.


Procedure1


Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

29.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

34.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
29.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

OK

30.CHECK VEHICLE TYPE

NG

41.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
30.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Adaptive Variable Suspension System A
w/o Adaptive Variable Suspension System B



A

31.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

B

32.CHECK VEHICLE TYPE
31.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

OK

32.CHECK VEHICLE TYPE

NG

42.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)
32.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B



A

33.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

B

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

33.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

OK

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

NG

43.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
34.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the B66 No. 1 global CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66,I76)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B66-2 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B66-13 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

35.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)

35.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66,I76)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B66-1 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B66-12 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

36.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

NG

38.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])
36.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66,I76)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B66-3 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B66-14 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

37.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ECM)

NG

39.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])
37.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66,I76)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B66-4 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B66-15 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

40.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ECM)
38.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

Pre-procedure1

a.

Disconnect the B20 brake actuator assembly (No.2 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66,I76)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B66-1 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B66-12 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

39.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

Pre-procedure1

a.

Disconnect the B19 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66,I76)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B66-3 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B66-14 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

40.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ECM)

Pre-procedure1

a.

Disconnect the B1*1, B2*2 or B70*3 ECM connector.

*1: for V35A-FTS

*2: for 1GR-FE

*3: for F33A-FTV



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66,I76)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B66-4 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B66-15 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ECM)

41.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

Pre-procedure1

a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


Procedure1


Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

42.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

Pre-procedure1

a.

Disconnect the Q11 absorber control ECU connector.


Procedure1


Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE ABSORBER CONTROL ECU

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

43.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

Pre-procedure1

a.

Disconnect the I57 engine stop and start ECU connector.


Procedure1


Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

44.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I118 No. 7 global CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-1 (CANH) - I118-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

50.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-3 (CANH) - I118-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

46.CHECK VEHICLE TYPE

NG

57.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
46.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Adaptive Variable Suspension System A
w/o Adaptive Variable Suspension System B



A

47.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

B

48.CHECK VEHICLE TYPE
47.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-2 (CANH) - I118-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

48.CHECK VEHICLE TYPE

NG

58.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)
48.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B



A

49.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

B

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

49.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-5 (CANH) - I118-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

NG

59.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
50.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the B66 No. 1 global CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

B66-2 (CANH) - B66-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

51.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)

51.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

B66-1 (CANH) - B66-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

52.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

NG

54.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])
52.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

B66-3 (CANH) - B66-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

53.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ECM)

NG

55.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])
53.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

B66-4 (CANH) - B66-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

56.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ECM)
54.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

Pre-procedure1

a.

Disconnect the B20 brake actuator assembly (No.2 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

B66-1 (CANH) - B66-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

55.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

Pre-procedure1

a.

Disconnect the B19 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

B66-3 (CANH) - B66-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

56.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ECM)

Pre-procedure1

a.

Disconnect the B1*1, B2*2 or B70*3 ECM connector.

*1: for V35A-FTS

*2: for 1GR-FE

*3: for F33A-FTV



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

B66-4 (CANH) - B66-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ECM)

57.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

Pre-procedure1

a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-3 (CANH) - I118-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

58.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

Pre-procedure1

a.

Disconnect the Q11 absorber control ECU connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-2 (CANH) - I118-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE ABSORBER CONTROL ECU

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

59.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

Pre-procedure1

a.

Disconnect the I57 engine stop and start ECU connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-5 (CANH) - I118-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

60.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I118 No. 7 global CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-1 (CANH) - I118-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

61.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

62.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
61.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-3 (CANH) - I118-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

NG

64.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
62.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the I118 No. 7 global CAN junction connector.


b.

Disconnect the B66 No. 1 global CAN junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

B66-2 (CANH) - B66-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

63.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)

63.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B66)Location & Routing

Click Connector(B66)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 1 Global CAN Junction Connector

B66-1 (CANH) - B66-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

65.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU] - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
64.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the I118 No. 7 global CAN junction connector.


b.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-12 (CAWH) - I42-13 (CAWL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)

65.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU] - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the B66 No. 1 global CAN junction connector.


Procedure1

b.

Disconnect the B20 brake actuator assembly (No.2 skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-16 (CA2H) - B20-17 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU] - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

66.CHECK FOR OPEN IN CAN BUS WIRE
NOTICE:

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.


HINT:

Operating the ignition switch, any other switches or door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C458715C08
1.51,0.073 1.927,0.323 0.417,0.25 0.552,1.667 0.74,1.667 0.74,1.667 1.052,0.781 true 0.75,1.896 0.938,1.896 0.938,1.896 1.167,0.781 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.625,0.115 2.083,0.313 0.458,0.198 10 false I42 0.135,1.552 0.604,1.771 0.469,0.219 10 false CAWL 0.26,1.823 0.823,2.073 0.563,0.25 10 false CAWH
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-12 (CAWH) - I42-13 (CAWL) Cable disconnected from negative (-) battery terminal Below 70 Ω



Result:
Proceed to
OK
NG



OK

67.CHECK FOR SHORT IN CAN BUS WIRES

NG

109.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
67.CHECK FOR SHORT IN CAN BUS WIRES
a.
C458715C08
1.51,0.073 1.927,0.323 0.417,0.25 0.552,1.667 0.74,1.667 0.74,1.667 1.052,0.781 true 0.75,1.896 0.938,1.896 0.938,1.896 1.167,0.781 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.625,0.115 2.083,0.313 0.458,0.198 10 false I42 0.135,1.552 0.604,1.771 0.469,0.219 10 false CAWL 0.26,1.823 0.823,2.073 0.563,0.25 10 false CAWH
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-12 (CAWH) - I42-13 (CAWL) Cable disconnected from negative (-) battery terminal 54 Ω or higher



Result:
Proceed to
OK
NG



OK

68.CHECK FOR SHORT TO B+ IN CAN BUS WIRE

NG

96.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
68.CHECK FOR SHORT TO B+ IN CAN BUS WIRE
a.
C458715C08
1.51,0.073 1.927,0.323 0.417,0.25 0.552,1.667 0.74,1.667 0.74,1.667 1.052,0.781 true 0.75,1.896 0.938,1.896 0.938,1.896 1.167,0.781 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.625,0.115 2.083,0.313 0.458,0.198 10 false I42 0.135,1.552 0.604,1.771 0.469,0.219 10 false CAWL 0.26,1.823 0.823,2.073 0.563,0.25 10 false CAWH
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42,I76)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I42-12 (CAWH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I42-13 (CAWL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

69.CHECK FOR SHORT TO GND IN CAN BUS WIRE

NG

83.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
69.CHECK FOR SHORT TO GND IN CAN BUS WIRE
a.
C458715C08
1.51,0.073 1.927,0.323 0.417,0.25 0.552,1.667 0.74,1.667 0.74,1.667 1.052,0.781 true 0.75,1.896 0.938,1.896 0.938,1.896 1.167,0.781 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.625,0.115 2.083,0.313 0.458,0.198 10 false I42 0.135,1.552 0.604,1.771 0.469,0.219 10 false CAWL 0.26,1.823 0.823,2.073 0.563,0.25 10 false CAWH
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42,I76)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I42-12 (CAWH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-13 (CAWL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

70.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
70.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I116 No. 1 CAN junction connector.


Procedure1


Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

71.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

74.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)
71.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

Result:
Proceed to
OK
NG



OK

72.CHECK VEHICLE TYPE

NG

81.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
72.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Adaptive Variable Suspension System A
w/o Adaptive Variable Suspension System B



A

73.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

B

REPLACE NO. 1 CAN JUNCTION CONNECTOR

73.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

82.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)
74.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the B48 No. 2 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48,I76)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B48-2 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B48-13 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

75.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

75.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48,I76)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B48-1 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B48-12 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

76.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

NG

78.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])
76.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48,I76)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B48-3 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B48-14 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

77.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - ECM)

NG

79.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])
77.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48,I76)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B48-4 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B48-15 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 CAN JUNCTION CONNECTOR

NG

80.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - ECM)
78.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

Pre-procedure1

a.

Disconnect the B20 brake actuator assembly (No.2 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48,I76)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B48-1 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B48-12 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

79.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

Pre-procedure1

a.

Disconnect the B19 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48,I76)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B48-3 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B48-14 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

80.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - ECM)

Pre-procedure1

a.

Disconnect the B1*1 or B70*2 ECM connector.

*1: for V35A-FTS

*2: for F33A-FTV



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48,I76)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B48-4 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B48-15 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - ECM)

81.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

Pre-procedure1

a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


Procedure1


Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

82.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

Pre-procedure1

a.

Disconnect the Q11 absorber control ECU connector.


Procedure1


Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE ABSORBER CONTROL ECU

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

83.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I116 No. 1 CAN junction connector.


Procedure1


Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

84.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

87.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)
84.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

Result:
Proceed to
OK
NG



OK

85.CHECK VEHICLE TYPE

NG

94.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
85.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Adaptive Variable Suspension System A
w/o Adaptive Variable Suspension System B



A

86.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

B

37.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - ECM)
86.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

95.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)
87.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the B48 No. 2 CAN junction connector.


Pre-procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48,I76)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B48-2 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B48-13 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

88.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

88.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48,I76)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B48-1 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B48-12 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

89.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

NG

91.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])
89.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48,I76)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B48-3 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B48-14 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

90.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - ECM)

NG

92.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])
90.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48,I76)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B48-4 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B48-15 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 CAN JUNCTION CONNECTOR

NG

93.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - ECM)
91.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

Pre-procedure1

a.

Disconnect the B20 brake actuator assembly (No.2 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48,I76)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B48-1 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B48-12 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

92.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

Pre-procedure1

a.

Disconnect the B19 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48,I76)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B48-3 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B48-14 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

93.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - ECM)

Pre-procedure1

a.

Disconnect the B1 or B70*2 ECM connector.

*1: for V35A-FTS

*2: for F33A-FTV



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48,I76)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B48-4 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B48-15 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - ECM)

94.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

Pre-procedure1

a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


Procedure1


Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

95.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

Pre-procedure1

a.

Disconnect the Q11 absorber control ECU connector.


Procedure1


Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE ABSORBER CONTROL ECU

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

96.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I116 No. 1 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I116)Location & Routing

Click Connector(I116)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 1 CAN Junction Connector

I116-2 (CANH) - I116-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

97.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

100.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)
97.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I116)Location & Routing

Click Connector(I116)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 1 CAN Junction Connector

I116-1 (CANH) - I116-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

98.CHECK VEHICLE TYPE

NG

107.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
98.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Adaptive Variable Suspension System A
w/o Adaptive Variable Suspension System B



A

99.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

B

REPLACE NO. 1 CAN JUNCTION CONNECTOR

99.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I116)Location & Routing

Click Connector(I116)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 1 CAN Junction Connector

I116-3 (CANH) - I116-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

108.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)
100.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the B48 No. 2 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

B48-2 (CANH) - B48-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

101.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

101.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

B48-1 (CANH) - B48-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

102.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

NG

104.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])
102.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

B48-3 (CANH) - B48-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

103.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - ECM)

NG

105.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])
103.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

B48-4 (CANH) - B48-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 CAN JUNCTION CONNECTOR

NG

106.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - ECM)
104.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

Pre-procedure1

a.

Disconnect the B20 brake actuator assembly (No.2 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

B48-1 (CANH) - B48-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

105.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

Pre-procedure1

a.

Disconnect the B19 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

B48-3 (CANH) - B48-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [NO. 1 SKID CONTROL ECU])

106.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - ECM)

Pre-procedure1

a.

Disconnect the B1*1 or B70*2 ECM connector.

*1: for V35A-FTS

*2: for F33A-FTV



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

B48-4 (CANH) - B48-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - ECM)

107.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

Pre-procedure1

a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I116)Location & Routing

Click Connector(I116)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 1 CAN Junction Connector

I116-1 (CANH) - I116-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

108.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

Pre-procedure1

a.

Disconnect the Q11 absorber control ECU connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I116)Location & Routing

Click Connector(I116)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 1 CAN Junction Connector

I116-3 (CANH) - I116-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE ABSORBER CONTROL ECU

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU)

109.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I116 No. 1 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I116)Location & Routing

Click Connector(I116)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 1 CAN Junction Connector

I116-2 (CANH) - I116-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

110.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

111.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)
110.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I116)Location & Routing

Click Connector(I116)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 1 CAN Junction Connector

I116-1 (CANH) - I116-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

113.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 1 CAN JUNCTION CONNECTOR)
111.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the I116 No. 1 CAN junction connector.


b.

Disconnect the B48 No. 2 CAN junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

B48-2 (CANH) - B48-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

112.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

112.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B48)Location & Routing

Click Connector(B48)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 CAN Junction Connector

B48-1 (CANH) - B48-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 CAN JUNCTION CONNECTOR

NG

114.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU] - NO. 2 CAN JUNCTION CONNECTOR)
113.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the I116 No. 1 CAN junction connector.


b.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-12 (CAWH) - I42-13 (CAWL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 1 CAN JUNCTION CONNECTOR)

114.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU] - NO. 2 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the B48 No. 2 CAN junction connector.


b.

Disconnect the B20 brake actuator assembly (No.2 skid control ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-16 (CA2H) - B20-17 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY [NO. 2 SKID CONTROL ECU] - NO. 2 CAN JUNCTION CONNECTOR)